Design of ternary clocked adiabatic static random access memory

Based on multi-valued logic,adiabatic circuits and the structure of ternary static random access memory (SRAM),a design scheme of a novel ternary clocked adiabatic SRAM is presented.The scheme adopts bootstrapped NMOS transistors,and an address decoder,a storage cell and a sense amplifier are charged and discharged in the adiabatic way,so the charges stored in the large switch capacitance of word lines,bit lines and the address decoder can be effectively restored to achieve energy recovery during reading and writing of ternary signals.The PSPICE simulation results indicate that the ternary clocked adiabatic SRAM has a correct logic function and low power consumption.Compared with ternary conventional SRAM,the average power consumption of the ternary adiabatic SRAM saves up to 68%in the same conditions.     

Performance analysis of a complete adiabatic logic system driven by the proposed power clock generator

We analyze the energy performance of a complete adiabatic circuit/system including the Power Clock Generator （PCG） at the 90 nm CMOS technology node. The energy performance in terms of the conversion efficiency of the PCG is extensively carried out under the variations of supply voltage, process comer and the driver transistor＇s width. We propose an energy-efficient singe cycle control circuit based on the two-stage comparator for the synchronous charge recovery sinusoidal power clock generator （PCG）. The proposed PCG is used to drive the 4-bit adiabatic Ripple Carry Adder （RCA） and their simulation results are compared with the adiabatic RCA driven by the reported PCG. We have also simulated the logically equivalent static CMOS RCA circuit to compare the energy saving of adiabatic and non-adiabatic logic circuits. In the clock frequency range from 25 MHz to 1GHz, the proposed PCG gives a maximum conversion efficiency of 56.48%. This research work shows how the design of an efficient PCG increases the energy saving of adiabatic logic.     

Design of ternary counter based on adiabatic domino circuit

By researching the ternary counter and low power circuit design method, a novel design of low power ternary Domino counter on switch-level is proposed. Firstly, the switch-level structure expression of ternary loop operation circuit with enable pin is derived according to the switch-signal theory, and the one bit ternary counter is obtained combining the ternary adiabatic Domino literal operation circuit and buffer. Then the switch-level structure expression of enable signal circuit is derived, and the four bits ternary counter is obtained by cascade connection. Finally, the circuit is simulated by Spice tool and the output waveforms transform in proper order indicating that the logic function is correct. The energy consumption of the four bits ternary adiabatic Domino counter is 63% less than the conventional Domino counterpart.     

A Novel Method for Power Analysis Based on Combinational Logic in Block Cipher Circuit

In this paper, we propose a method that builds power model template according to input transi- tions of combinatorial logic circuit. By computing its cor- relation with the overall power consumption of a crypto- graphic circuit, we are able to recover the secret key. Sev- eral simulation-based experiments have been conducted, which verifies the feasibility of our method and shows that the combinatorial logic is also faced with the problem of information leakage in power analysis cases. Compared with DPA （Differential power analysis） and CPA （Corre- lation power analysis）, our attack is fairly effective against the cryptographic circuits whose protection is only imple- mented on the register parts of the sequential circuit. In addition, a few topics for further research, as well as the ad- vices for more precise power model and countermeasures, are presented at the end of the paper.     

DESIGN OF TWO-PHASE SINUSOIDAL POWER CLOCK AND CLOCKED TRANSMISSION GATE ADIABATIC LOGIC CIRCUIT

First the research is conducted on the design of the two-phase sinusoidal power clock generator in this paper. Then the design of the new adiabatic logic circuit adopting the two-phase sinusoidal power clocks--Clocked Transmission Gate Adiabatic Logic （CTGAL） circuit is presented. This circuit makes use of the clocked transmission gates to sample the input signals, then the output loads are charged and discharged in a fully adiabatic manner by using bootstrapped N-Channel Metal Oxide Semiconductor （NMOS） and Complementary Metal Oxide Semiconductor （CMOS） latch structure. Finally, with the parameters of Taiwan Semiconductor Manufacturing Company （TSMC） 0.25um CMOS device, the transient energy consumption of CTGAL, Bootstrap Charge-Recovery Logic （BCRL） and Pass-transistor Adiabatic Logic （PAL） including their clock generators is simulated. The simulation result indicates that CTGAL circuit has the characteristic of remarkably low energy consumption.     

THE QUATERNARY INTERFACE TECHNIQUE IN ECL INTEGRATED CIRCUITS

The theory of differential current switches which applies to the design of multivaluedECL circuits is introduced.In this theory,the switching state of differential transistor pairand signal in ECL circuits are described by switching variables and quaternary signal variables,respectively.he connection operations between the two kinds of variables are introduced todescribe the action process between switching element and signal in the circuits.Based on thistheory,two kinds of interface circuits-2-4 encoder and 4-2 decoder are designed.The computersimulation for the designed circuits by using SPICE program confirms that both circuits havecorrect logic functions,desired DO transfer characteristics and transient characteristics.Theseinterface circuits are compatible with binary circuits in the integrated process,the power supplyequipment,the logic stage and the transient characteristic.Therefore,they can be used as input-output interface of the existing binary ECL integrated circuits so as to decrease the number ofpins of a chip and the connections between chips.     

Scaling trends in energy recovery logic: an analytical approach

This paper presents an analytical model to study the scaling trends in energy recovery logic.The energy performance of conventional CMOS and energy recovery logic are compared with scaling the design and technology parameters such as supply voltage,device threshold voltage and gate oxide thickness.The proposed analytical model is validated with simulation results at 90 nm and 65 nm CMOS technology nodes and predicts the scaling behavior accurately that help us to design an energy-efficient CMOS digital circuit design at the nanoscale.This research work shows the adiabatic switching as an ultra-low-power circuit technique for sub-100 nm digital CMOS circuit applications.     

PMGA and its application in area and power optimization for ternary FPRM circuit

Based on the research of population migration algorithms (PMAs), a population migration genetic algorithm (PMGA) is proposed, combining a PMA with a genetic algorithm. A scheme of area and power optimization for a ternary FPRM circuit is proposed by using the PMGA. Firstly, according to the ternary FPRM logic function expression, area and power estimation models are established. Secondly, the PMGA is used to search for the best area and power polarity. Finally, 10 MCNC Benchmark circuits are used to verify the effectiveness of the proposed method. The results show that the ternary FPRM circuits optimized by the PMGA saved 13.33% area and 20.00% power on average than the corresponding FPRM circuits optimized by a whole annealing genetic algorithm.     

A Combinational Power Analysis Method against Cryptographic Hardware

Power analysis is a non-invasive attack against cryptographic hardware,which effectively exploits runtime power consumption characteristics of circuits.This paper proposes a new power model which combines Hamming Distance model and the model based on the template value of power consumption in combinational logic circuit.The new model can describe the power consumption characteristics of sequential logic circuits and those of combinational logic as well.The new model can be used to improve the existing power analysis methods and detect the information leakage of power consumption.Experimental results show that,compared to CPA(Correlation Power Analysis)method,our proposed attack which adopt the combinational model is more efficient in terms of the number of required power traces.     

DESIGN OF SYMMETRIC TERNARY CURRENT-MODE CMOS CIRCUITS

By applying switch-signal theory, the theory of transmission current-switches based on symmetric ternary logic is proposed, this theory is suitable to design symmetric ternary current-mode CMOS circuits. The symmetric ternary current-mode CMOS circuits designed by using this theory not only have simpler circuit structures and correct logic functions, but also can process bidirectional signals.     

Software Radio——Software Radio： A Review of Design Considerations and Digital Hardware Choices

This paper reviews the requirements for Software Defined Radio （SDR） systems for high-speed wireless applications and compares how well the different technology choices available- from ASICs, FPGAs to digital signal processors （DSPs） and general purpose processors （GPPs） - meet them.     

EEFA： Energy Efficiency Frame Aggregation Scheduling Algorithm for IEEE 802.11n Wireless Network

Packet size is restricted due to the error-prone wireless channel which drops the network energy utilization. Furthermore, the frequent packet retransmissions also lead to energy waste. In order to improve the energy efficiency of wireless networks and save the energy of wireless devices, EEFA （Energy Efficiency Frame Aggregation）, a frame aggregation based energy-efficient scheduling algorithm for IEEE 802.11n wireless network, is proposed. EEFA changes the size of aggregated frame dynamically according to the frame error rate, so as to ensure the data transmission and retransmissions completed during the TXOP and reduce energy consumption of channel contention. NS2 simulation results show that EEFA algorithm achieves better performance than the original frame-aggregation algorithm.     

SDN-Based Data Offioading for 5G Mobile Networks

The rapid growth of 3G/4G enabled devices such as smartphones and tablets in large numbers has created increased demand formobile data services.Wi-Fi offloading helps satisfy the requirements of data-rich applications and terminals with improved multi-media.Wi-Fi is an essential approach to alleviating mobile data traffic load on a cellular network because it provides extra capaci-ty and improves overall performance.In this paper,we propose an integrated LTE/Wi-Fi architecture with software-defined net-working(SDN)abstraction in mobile backhaul and enhanced components that facilitate the move towards next-generation 5G mo-bile networks.Our proposed architecture enables programmable offloading policies that take into account real-time network condi-tions as well as the status of devices and applications.This mechanism improves overall network performance by deriving real-time policies and steering traffic between cellular and Wi-Fi networks more efficiently.     

应力和电阻率可控的适用于高品质因子MEMS器件的原位掺硼LPCVD多晶硅薄膜

The simultaneous control of residual stress and resistivity of polysilicon thin films by adjusting the deposition parameters and annealing conditions is studied. In situ boron doped polysilicon thin films deposited at 520 ℃ by low pressure chemical vapor deposition （LPCVD） are amorphous with relatively large compressive residual stress and high resistivity. Annealing the amorphous films in a temperature range of 600-800 ℃ gives polysilicon films nearly zero-stress and relatively low resistivity. The low residual stress and low resistivity make the polysilicon films attractive for potential applications in micro-electro-mechanical-systems （MEMS） devices, especially in high resonance frequency （high-f） and high quality factor （high-Q） MEMS resonators. In addition, polysilicon thin films deposited at 570 ℃ and those without the post annealing process have low resistivities of 2-5 mΩ·cm. These reported approaches avoid the high temperature annealing process （〉 1000 ℃）, and the promising properties of these films make them suitable for high-Q and high-f MEMS devices.     

Survivable Virtual Network Mapping Using Optimal Backup Topology in Virtualized SDN

Software-Defined Network architecture offers network virtualization through a hypervisor plane to share the same physical substrate among multiple virtual networks. However, for this hypervisor plane, how to map a virtual network to the physical substrate while guaranteeing the survivability in the event of failures, is extremely important. In this paper, we present an efficient virtual network mapping approach using optimal backup topology to survive a single link failure with less resource consumption. Firstly, according to whether the path splitting is supported by virtual networks, we propose the OBT-I and OBT-II algorithms respectively to generate an optimal backup topology which minimizes the total amount of bandwidth constraints. Secondly, we propose a Virtual Network Mapping algorithm with coordinated Primary and Backup Topology （VNM-PBT） to make the best of the substrate network resource. The simulation experiments show that our proposed approach can reduce the average resource consumption and execution time cost, while improving the request acceptance ratio of VNs.     

用于ZigBee的2.4GHz低功耗双增益低噪声放大器

This paper presents a fully differential dual gain low noise amplifier（DGLNA） for low power 2.45-GHz ZigBee/IEEE 802.15.4 applications.The effect of input parasitics on the inductively degenerated cascode LNA is analyzed.Circuit design details within the guidelines of the analysis are presented.The chip was implemented in SMIC 0.18-μm 1P6M RF/mixed signal CMOS process.The DGLNA achieves a maximum gain of 8 dB and a minimum gain of 1 dB with good input return loss.In high gain mode, the measured noise figure（NF） is 2.3-3 dB in the whole 2.45-GHz ISM band.The measured 1-dB compression point, IIP3 and IIP2 is-9, 1 and 33 dBm, respectively.The DGLNA consumes 2 mA of current from a 1.8 V power supply.     

应用于低中频和零中频DVB调谐器中8阶信道滤波器设计

An eighth order active-RC filter for low-IF and zero-IF DVB tuner applications is presented, which is implemented in Butterworth biquad structure. An automatic frequency tuning circuit is introduced to compensate the cut-off frequency variation using a 6-bit switched-capacitor array. Switched-resistor arrays are adopted to cover different cut-off frequencies in low-IF and zero-IF modes. Measurement results show that precise cut-off frequencies at 2.5, 3, 3.5 and 4 MHz in zero-IF mode, 5, 6, 7 and 8 MHz in low-IF mode can be achieved, 60 dB frequency attenuation can be obtained at 20 MHz, and the in-band group delay agrees well with the simulation. Two-tone testing shows the in-band IM3 achieves -52 dB and the out-band IM3 achieves -55 dB with -11 dBm input power. This proposed filter circuit, fabricated in a SMIC 0.18μm CMOS process, consumes 4 mA current with 1.8 V power supply.     

Distributed Power Control for Energy Conservation in Hybrid Cellular Network with Device-to-Device Communication

Device-to-Device （D2D） com- munication has been proposed as a promising implementation of green communication to benefit the existed cellular network. In order to limit cross-tier interference while explore the gain of short-range communication, we devise a series of distributed power control （DPC） schemes for energy conservation （EC） and enhancement of radio resource utilization in the hybrid system. Firstly, a constrained opportunistic power control model is built up to take advantage of the interference avoidance methodology in the presence of service requirement and power constraint. Then, biasing scheme and admission control are added to evade ineffective power consumption and maintain the feasibility of the system. Upon feasibility, a non-cooperative game is further formulated to exploit the profit in EC with minor influence on spectral efficiency （SE）. The convergence of the DPC schemes is validated and their performance is confirmed via simulation results.     

Large-signal characterizations of DDR IMPATT devices based on group Ⅲ-Ⅴ semiconductors at millimeter-wave and terahertz frequencies

Large-signal （L-S） characterizations of double-drift region （DDR） impact avalanche transit time （IM- PATT） devices based on group III-V semiconductors such as wurtzite （Wz） GaN, GaAs and InP have been carried out at both millimeter-wave （mm-wave） and terahertz （THz） frequency bands. A L-S simulation technique based on a non-sinusoidal voltage excitation （NSVE） model developed by the authors has been used to obtain the high frequency properties of the above mentioned devices. The effect of band-to-band tunneling on the L-S properties of the device at different mm-wave and THz frequencies are also investigated. Similar studies are also carried out for DDR IMPATTs based on the most popular semiconductor material, i.e. Si, for the sake of comparison. A compara- tive study of the devices based on conventional semiconductor materials （i.e. GaAs, InP and Si） with those based on Wz-GaN shows significantly better performance capabilities of the latter at both mm-wave and THz frequencies.     

具有频率调谐的GNSS接收机双模复数滤波器

A fifth/seventh order dual-mode OTA-C complex filter for global navigation satellite system receivers is implemented in a 0.18μm CMOS process.This filter can be configured as the narrow mode of a 4.4 MHz bandwidth center at 4.1 MHz or the wide mode of a 22 MHz bandwidth center at 15.42 MHz.A fully differential OTA with source degeneration is used to provide sufficient linearity.Furthermore,a ring CCO based frequency tuning scheme is proposed to reduce frequency variation.The measured results show that in narrow-band mode the image rejection ratio（IMRR）is 35 dB,the filter dissipates 0.8 mA from the 1.8 V power supply,and the out-of-band rejection is 50 dB at 6 MHz offset.In wide-band mode,IMRR is 28 dB and the filter dissipates 3.2 mA.The frequency tuning error is less than±2%.