Synthesis and Luminescence Properties of Ba2 MgSi2 O7 :Eu2+ under UV Excitation

Eu2 activated pyrosilicate phosphor were prepared under a reducing atmosphere by solid-state reaction.The crystal structure of Ba2 MgSi2 O7: Eu2 was analyzed by XRD method.The excitation spectrum of Ba2MgSi2 O7; Eu2 is composed of two broad bands centered at about 310 nm and 395 nm respectively.In the emission spectra, the peak wavelength is at about 507 nm under 380 nm UV excitation.It was found that the introduction of Zn2 into Ba2MgSi2O7: Eu2 Can effectively increase its emission intensity without changing the position of emission peak.And the Eu2 and Ce3 codoped pyrosilicate phosphor is the efficient bluish green phosphor under the excitation of long UV light and its emission intensity is stronger than Eu2 doped pyrosilicate phosphor.     

Luminescence and Preparation of LED Phosphor Ca8Mg(SiO4)4Cl2:Eu2+

Calcium magnesium chlorosilicate doped by europium, Ca8Mg(SiO4)4Cl2:Eu2 , was prepared by the solid state reaction at high temperature. The compound obtained is pure Ca8Mg(SiO4)4Cl2 phase with cubic structure. Its average particle size is 5 μm, and it has good dispersity and morphological form. The excitation spectrum of Ca8Mg(SiO4)4Cl2:Eu2 is a wide band, which covers from 270 to 480 nm. The emission spectrum is also a wide band peaked at 510 nm. The luminescent intensity reaches to the maximum when the concentration of Eu2 is 2%. The wavelength of emission and excitation of the phosphor with various Eu2 contents keeps constant. This spectrum range matches violet and blue LED chips very well, and its strong luminescence intensity is suitable for a green phosphor of tricolor phosphor of white light LED.     

Enhancement of photoluminescence of Ba2SiO4：Eu^2＋ by co-doping of La^3＋ or Y^3＋

Green light-emitting Ba2SiO4:Eu2+ phosphors co-doped with La or Y were synthesized by conventional solid-state reaction technique in reductive atmosphere (a mixture of 5% H2 and 95% N2). The results showed that the co-doping of La and Y could greatly enhance the fluorescence intensity of Ba2SiO4:Eu2+ phosphors. The optimum doping concentration expressed by the x value in (Ba0.985-1.5xREx)2SiO4: 0.03Eu2+ (RE=La or Y) was determined to be of 0.05. The excitation and emission peaks of all as-synthesized phosphors were wide bands. The excitation bands ranged from 250 to 400 nm, which matched well with the wavelength of near ultraviolet white light-emitting diodes (LED) chip and could be used as a potential candidate for the fabrication of white LED. The emission bands from 450 to 550 nm were typical 5d-4f transition emission of Eu2+ and displayed un-symmetry profiles because of the two substitution sites of Ba2+ with Eu2+.     

Single-phase full-color Ba_3Lu_2（SiO_4）_3：Eu~（2＋） phosphor for white-light emitting diodes

we developed a new silicate-based full-color phosphor Ba3Lu2(SiO4)3:Eu2+ through solid state reaction.The host crystal structure was isostructural with Ca3Y2(SiO4)3 instead of garnet-type.The phosphor absorbed near-ultraviolet light from 250 to 400 nm,which was very suitable for a color converter of white LED that used UV-LED as the primary light source.The photoluminescence peak wavelength of Ba3Lu2(SiO4)3:Eu2+ was about 461 nm and a shoulder peak was around 522 nm,which resulted from the 5d-4f transition ...     

Photoluminescence Characteristics of Gd2Mo3O9 ： Eu Phosphor Particles by Solid State Reaction Method

Eu^3＋-doped Gd2Mo3O9 was prepared by solid-state reaction method using Na2CO3 as flux and characterized by powder X-ray diffractometry. According to X-ray diffraction, this material belonged to a tetragonal system with space group I41/α. The effects of flux content and sintering temperature on the luminescent properties were investigated with the emission and excitation spectra. The results showed that flux content and sintering temperature had effects on the luminescent properties, the optimized flux content and the best temperature was 3 % and 800 ℃ respectively. The excitation and emission spectra also showed that this phosphor could be effectively excited by C-T band （280 nm）, ultraviolet light 395 nm and blue light 465 nm. The wavelengths at 395 and 465 nm were nicely fitting in with the widely applied output wavelengths of ultraviolet or blue LED chips. Integrated emission intensity of Gd2Mo3O9 ： Eu was twice higher than that of Y2O2S ： Eu^3 ＋ under 395 nm excitation. The Eu^3＋ doped Gd2Mo309 phosphor may be a better candidate in solid-state lighting applications.     

Luminescent characteristics of Ba3Y2（BO3）4：Eu^3＋ phosphor for white LED

The Ba3Y2（BO3）4：Eu^3＋ phosphor was synthesized using a high temperature solid-state reaction method and the luminescent characteristics were investigated. The emission spectrum exhibited one strong red emission at 613 nm, corresponding to the electric dipole 5D0-TF2 transition of Eu^3＋, under 365 nm excitation. The excitation spectrum of 613 nm indicated that the Ba3Y2（BO3）n：Eu^3＋ phosphor was effectively excited by ultraviolet （UV） （254, 365 and 400 nm） and blue （470 nm） light. The effect of Eu^3＋ concentration on the 613 nm emission of the Ba3Y2（BO3）n：Eu^3＋ phosphor was measured. The results showed that the emission intensity increased with increasing Eu^3＋ concentration, and then decreased. The CIE color coordinates of Ba3Y2（BO3）4：Eu^3＋ phosphor were x=0.641 and y=0.359 at 15 mol.% Eu^3＋.     

Luminescence Properties of Green-Emitting Phosphor （Ba1- x, Srx ） 2 SiO4 ： EU^2＋ for White LEDS

The （Ba1- x, Srx ） 2 SiO4 ： EU^2＋ green-emitting phosphors were synthesized by conventional solid-state reaction in a CO-reductive atmosphere, and their luminescent properties were investigated. The XRD data show that the Ba/Sr ratio not only affects the lattice parameters, but also influences the emission peak. The excitation spectra indicate that this phosphor can be effectively excited by UV light from 370 to 470 nm. The emission band is due to the 4f^65d^1→4f^7 transition of the Eu^2＋ ion. With an increase in x, the emission band shifts to longer wavelength and the reason was discussed. The emission spectra exhibit a satisfactory green performance under different excitation wavelength（380,398,412,420,460 nm）. （Ba1- x, Srx ） 2 SiO4 ： EU^2＋ is a promising phosphor for green white-lighting-emission diode by ultraviolet chip.     

Ba1-xSrxMgSiO4:Eu2+,Mn2+: A novel tunable single-matrix tricolor phosphor for W-LED

The Ba1-xSrxMgSiO4:Eu2+,Mn2+ phosphors were prepared by solid-state reaction. Their photoluminescence properties were inves-tigated with fluorescence spectrum and CIE chromaticity. The emission color of Eu2+ in Ba0.98-xSrxMgSiO4:0.02Eu2+ could be tuned from green to blue by adjusting the content of Sr2+. The blue emission of Eu2+ overlapped well with the excitation spectra of Mn2+, leading to an ef-ficient energy transfer from Eu2+ to Mn2+ in Ba0.98-xSrxMg1-ySiO4:0.02Eu2+,yMn2+. Ba0.93Sr0.03Mg1-ySiO4:0.02Eu2+,yMn2+ could emit three ef-ficient broad bands at 440, 530 and 640 nm. The emission color of Ba0.93Sr0.03Mg1-ySiO4:0.02Eu2+,yMn2+ could be tuned from greenish blue to yellowish white by increasing the content of Mn2+ from 0 to 0.1. By changing the content of Sr2+/Mn2+, white-light with different hues could be conveniently obtained in the Ba1-xSrxMgSiO4:Eu2+,Mn2+ phosphors. The results showed that Ba1-xSrxMgSiO4:Eu2+,Mn2+ is a promising single-phased tricolor phosphor in the fabrication of W-LED.     

Photoluminescence properties of M2ZnSi2O7:Eu2+（M=Sr,Ba）

The hardystonite phosphors of Eu2+ activated M2ZnSi2O7(M=Sr,Ba) were synthesized by combustion-assisted method.They were systematically characterized by photoluminescence excitation and emission spectra.The emission spectra of these two phosphors showed that the main emission peaks are at 475 and 503 nm due to 4f65d1→4f7 transition of Eu2+.Both phosphors could be efficiently excited in the wavelength range of 250-425 nm where the near ultraviolet light-emitting diode was well matched.The(x,y) color coordinates were determined with the emission values(x,y)=(0.41,0.21) and(0.16,0.45) for the M2ZnSi2O7:Eu2+(M=Sr,Ba) phosphors.     

红色Sr1-2xNaxWO4∶Eux3+荧光体的制备与发光性能

采用传统高温固相法,以钨酸锶为基质材料,掺杂稀土Eu3+制备了可被紫色光有效激发的红色荧光粉Sr1-2xNaxWO4∶Eu3x+。通过测定与分析样品Sr1-2xNaxWO4∶Eu3x+的激发和发射光谱,发现激发光谱在395nm处吸收值最大,发射光谱的发射主峰位于613nm处,属于Eu3+的5D0→7F2特征跃迁。不同的Eu3+掺杂浓度下样品发光强度不同,当x=0.07时发光强度最佳。电荷补偿剂Na+对样品发光强度的影响很大,主要原因是Na+的加入会影响基质的晶体结构,当Na+的含量与Eu3+含量相同时样品发光强度最好,Na+含量增加到一定程度后基质结晶不完善,荧光体的发光强度急剧下降。     

SrAl2O4∶Eu2+,Dy3+磷光粉低成本制备工艺及发光性能研究

以工业铝酸钠溶液制备的氢氧化铝为铝基原料,采用高温固相反应法合成了SrAl2O4∶Eu2+,Dy3+磷光粉,考察了稀土掺杂量、烧结温度及硼酸加入量对其发光性能、激发光谱及发射光谱的影响,并通过XRD谱及余辉衰减曲线对最佳工艺条件下制备的样品进行表征。结果表明,当稀土掺杂量x(Eu)=3%、x(Dy)=3%,烧结温度为1 300℃,烧结时间为4h,硼酸加入量w(H3BO3)=9%时,所制备磷光粉样品仍保持SrAl2O4的晶体结构,其发光性能最好,发光强度最大,主激发波长在360nm左右,主发射波长在510nm左右;余辉为黄绿色,衰减时间长。     

Luminescent Properties of Green Phosphor Ca8Mg（SiO4 ）4 Cl2：EU^2＋ , DY^3＋ for LED Applications

The new phosphor calcium magnesium chlorosilicate, codoped with Eu^2＋ and Dy^3＋, was synthesized with the help of the high temperature solid state reaction in reducing atmosphere. The excitation and emission spectra were very similar to that of Ca8Mg（SiO4）4Cl2 ：Eu^2＋, and the Dy^3＋ concentration influenced the emission intensity of this phosphor. The intensity of Eu^2＋ and Dy^3＋ codoped CMSC was stronger than that of Eu^2＋ singly doped CMSC. The emission spectrum of the Dy^3＋ ion overlapped the absorption band of the Eu^2＋ ion, indicating that an energy transfer from Dy^3＋ to Eu^2＋ took place in CMSC：Eu^2＋, Dy^3＋ phosphor. The mechanism of the energy transfer from Dy^3＋ tO Eu^2＋, in this phosphor, might be resonant energy transfer.     

Synthesis of Long Afterglow Phosphors MAl2O4:Eu2+, Dy3+(M=Ca, Sr, Ba) by Microemulsion Method and Their Luminescent Properties

Long afterglow phosphors MAl2O4:Eu2 , Dy3 (M=Ca, Sr, Ba) were synthesized by microemulsion method, and their crystal structure and luminescent properties were compared and investigated. XRD patterns of samples indicate that phosphors CaAl2O4:Eu2 , Dy3 and SrAl2O4:Eu2 , Dy3 are with monoclinic crystal structure and phosphor BaAl2O4:Eu2 , Dy3 is with hexagonal crystal structure. The wide range of excitation spectrum of phosphors MAl2O4:Eu2 , Dy3 (M=Ca,Sr,Ba) indicates that the luminescent materials can be excited by light from ultraviolet ray to visible light and the maximum emission wavelength of phosphors MAl2O4:Eu2 , Dy3 (M=Ca, Sr, Ba) is found mainly at λem of 440 nm (M=Ca), 520 nm (M=Sr) and 496 nm (M=Ba) respectively, the corresponding colors of emission light are blue, green and cyna-green respectively. The afterglow decay tendency of phosphors can be summarized as three processes: initial rapid decay, intermediate transitional decay and very long slow decay. Afterglow decay curves coincide with formula I=At-n, and the sequence of afterglow intensity and time is Sr＞Ca＞Ba.     

Preparation and Luminescence Properties of the New Long Phosphorescent Phosphors Ba1-xCaxAl2O4∶Eu2+,Dy3+

New long phosphorescent phosphors Ba1-xCaxAl2O4∶Eu2 , Dy3 with tunable color emission were prepared and studied. The emission spectra show that the tuning range of the color emission of the phosphors is between 498 and 440 nm, which is dependent on x, under the excitation of UV. The wavelength of the afterglow increases with the increasing of x until x equals 0.6. The XRD patterns show that the single phase limit in the phosphors is below x value of 0.4. The Thermoluminescence spectra were measured to investigate the traps created by the doping of Dy3 .     

红色荧光粉La2O3：Eu3＋的合成及发光性质

利用复合沉淀法制备了性能稳定的红色荧光粉La2O3：Eu3＋,同时研究了煅烧温度及掺杂Eu3＋浓度对La2O3：Eu。’发光性能的影响．通过X射线粉末衍射（XRD）和扫描电子显微镜（SEM）来表征荧光粉的晶体结构和颗粒大小及形貌：用激发光谱和发射光谱以及荧光衰减曲线来袁征荧光粉的荧光性能．结果表明：煅烧温度在900℃时,所制备样品为六方晶系La2O3：Eun;SEM图显示掺杂Eu0＋含量为5％的La2O3颗粒直径为15μm左右．最大发射波长和激发波长分别为626nm和396nm,发射光谱中596nm和626nm的发射峰对应的是Eu3＋离子的0D—F1和5D—F2跃迁,其荧光寿命为0．754ms．     

白光LED用LaPO4:Eu3+红色荧光粉的合成与表征

利用水热法制备了性能稳定的红色荧光粉LaPO4:Eu3+,同时研究了不同的Eu3+浓度、煅烧温度对荧光粉发光性能的影响.通过X射线粉末衍射(XRD)和扫描电子显微镜(SEM)来表征荧光粉的晶体结构和颗粒大小及形貌;用激发光谱和发射光谱以及荧光衰减曲线来表征荧光粉的荧光性能.结果表明:未煅烧时前躯体主要是六方晶相LaPO4·0.5H2O,煅烧温度在900℃时,所制备样品为单斜相LaPO4:Eu3+;SEM图像显示5 at.%Eu3+掺杂LaPO4呈椭球形,颗粒长约为500 nm,宽约为300 nm.最大发射波长和激发波长分别为592 nm和393 nm,发射光谱中592 nm和612 nm的发射峰对应的是Eu3+离子的5D0→7F1和5D0→7F2跃迁.其荧光寿命为3.32 ms.     

Combustion synthesis and luminescence properties of blue NaBaPO4:Eu2+ phosphor

The blue-emitting phosphor NaBaPO4:Eu2+ was prepared by the combustion method. The phase structure and microstructure of the as-prepared samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Under the excita-tion wavelength of 360 nm, the emission spectrum exhibited only one blue band centering at 435 nm, which was ascribed to the 4f65d1→4f7 transition on Eu2+ ions. Compared with the phosphor obtained by solid-state reaction method, the relative emission intensity of sample ob-tained by combustion method increased slightly. The decay times and the temperature dependence luminescence intensities (25-300 oC) were discussed in order to further investigate the potential applications. Furthermore, Eu2+-doped NaBaPO4 phosphor showed higher thermally sta-ble luminescence comparable to commercially available Y3Al5O12:Ce3+ (YAG:Ce3+) phosphor. All the investigated suggestions that Na-BaPO4:Eu2+ is a good phosphor candidate applied in white light emitting diode.     

Luminescence Properties of Eu~(2 ) and Mn~(2 ) Co-Doped Ca_8Mg(SiO_4)_4Cl_2

The green phosphor for white LED, Ca8Mg(SiO4)4Cl2∶Eu2+, Mn2+, was synthesized by high temperature solid state reaction under reducing atmosphere. During the process of the phosphor prepared, the excess CaCl2 can improve the intensity of emission. The experimental results indicate that there is an effective energy transfer from Eu2+ to Mn2+in Ca8Mg(SiO4)4Cl2 host. This kind of energy transfer may be due to resonance transfer, and this energy transfer is limited.     

Synthesis of Long Afterglow SrAl2O4 :Eu2+, Dy3+ Phosphor by Microemulsion Method

Long afterglow SrAl2 O4: Eu2 , Dy3 phosphor was synthesized by microemulsion method. The synthesized phosphor was characterized by XRD. XRD pattern indicates that the phosphor has monoclinic SrAl2 O4 crystal structre.The microstructure of the phosphor was investigated by SEM and TEM. The excitation spectrum, emission spectrum and afterglow decay curve were measured, the wide range of excitation wavelength indicated that the luminescent material could be excited by the light from ultraviolet ray to visible light, and the emission maximum was found to peak mainly at λem of 525 nm. The sample excited by ultraviolet visible light could emit bright green light.     

Research of Luminescence Properties on MO-RE2 O3 -B2 O3:Eu, Mn(M=Mg, Ca, Sr; RE=Y, La, Gd)

A series of phosphor of MO-RE2 O3-B2 O3: Eu, Mn ( M = Mg, Ca, Sr; RE = Y, La, Gd) were prepared and studied.Excitation spectra exhibited high absorption in UV region (370 ～ 400 nm).There existed two valence states for europium ions Eu2 and Eu 3 , the broad emission band peaking at 515 nm correspond to the 5d-4f emission transition of Eu2 , the sharp emission peaking at 590 and 610 nm correspond to the 5D0→7FJ(J = 1,2,3,4) emission transition of Eu 3 By the introduction of Mg and Y into MO-RE2O3-B2O3: Eu, blue-green emission was restrained ultimately and red emission peaking at 610 nm was enhanced strongly, intensity and colorimetric purity of red light were both enhanced.Furthermore, Mg1-xSrxO-Y2O3-B2O3: Eu was also researched, the introduction of Sr into MgO-Y2O3-B2O3:Eu gives rise to a shift to longer wavelengths of the position of the excitation peak, and the emission spectra varies with the increasing of x simultaneously.