CSD法制备PZT/Bi2Ti2O7薄膜的研究

用化学溶液分解（ＣＳＤ）法制备Ｐｂ（Ｚｒ０．５Ｔｉ０．５）Ｏ３（ＰＺＴ）和Ｂｉ２Ｔｉ２Ｏ７薄膜,利用Ｘ－射线衍射技术研究了以Ｂｉ２Ｔｉ２Ｏ７为籽晶层的ＰＺＴ薄膜的结晶性。实验结果表明,以高（１１１）取向的Ｂｉ２Ｔｉ２Ｏ７为籽晶层可获得高结晶性的ＰＺＴ薄膜,在７５０℃退火１０ｍｉｎ的ＰＺＴ／Ｂｉ２Ｔｉ２Ｏ７薄膜具有单一的钙钛矿相。     

钛酸铋薄膜的室温脉冲激光沉积研究

在室温下,采用脉冲激光沉积（ＰＬＤ）技术在７．６２ｃｍＰｔ／Ｔｉ／ＳｉＯ２／Ｓｉ（１００）衬底上制备了钛酸铋（Ｂｉ４Ｔｉ３Ｏ１２）薄膜。Ｂｉ４Ｔｉ３Ｏ１２薄膜的厚度和组分均匀性采用卢瑟福背散射（ＲＢＳ）和扩展电阻技术（ＳＲＰ）来分析、表征;采用Ｘ射线衍射（ＸＲＤ）技术研究了薄膜的退火特性。研究发现单独用常规退火或快速退火热处理的Ｂｉ４Ｔｉ３Ｏ１２薄膜中较容易出现Ｂｉ２Ｔｉ２Ｏ７杂相;而采用常规退火和快速退火相结合的方法,较好地解决了杂相出现的问题,得到相结构和结晶性完好的Ｂｉ４Ｔｉ３Ｏ１２薄膜。透射电子显微镜实验和扩展电阻实验表明,室温下制备的Ｂｉ４Ｔｉ３Ｏ１２薄膜具有良好的表面和界面特性。     

后续热处理配合PLD制备铁电PZT薄膜及其工艺优化研究

利用ＡｒＦ准分子脉冲激光沉积工艺在Ｐｔ／ＳｉＯ２／Ｓｉ衬底上制行了Ｐｂ（Ｚｒ５２Ｔｉ４８）Ｏ３（ＰＺＴ）薄膜。并用Ｘ射线衍射分析方法研究了不同后续热处理对薄膜相组成和相结构转变的影响。     

Co／Si和Co／SiO_2界面反应的观察

本文用Ｘ射线衍射（ＸＲＤ）和高分辨电镜研究Ｃｏ薄膜在氩气气氛或真空条件下热处理时Ｃｏ／Ｓｉ和Ｃｏ／ＳｉＯ２体系的界面反应．结果表明：在氩气氛下４５０℃处理时，Ｃｏ薄膜均发生氧化，在Ｃｏ／Ｓｉ界面同时有硅化物形成，而在Ｃｏ／ＳｉＯ２界面，无硅化物产生．在真空条件下５００℃处理１小时，薄膜没有氧化，在Ｃｏ／Ｓｉ界面形成完整的ＣｏＳｉ２外延层．     

Co／Ti／Si三元固相反应外延生长CoSi2薄膜

研究采用Ｃｏ／Ｔｉ／Ｓｉ三元固相反应的方法生长外延ＣｏＳｉ２薄膜。通过选择适当的热处理条件，采用步退火，在Ｓｉ（１００）和Ｓｉ（１１１）衬底上均成功获得外延ＣｏＳｉ２薄膜。实验用ＸＲＤ．ＴＥＭ、ＲＢＳ／ｃｈａｎｎｅｌｉｎｇ等测试技术分析ＣｏＳｉ２薄膜外延特性，得到的ＣｏＳｉ２／Ｓｉ薄膜的ＲＢＳ／ｃｈａｎｎｅｌｉｎｇ最低产额Ｘｍｉｎ达到１０－１４％，实验时ＣｏＳｉ２／Ｓｉ（１１１）样品，分别沿Ｓｉ衬     

多层结构铁电薄膜的I—V特性性能的研究

为ＦＲＡＭ、ＦＦＥＴ和ＦＤＭ的实际应用研究，提出了多层结构铁电薄膜的设计思想，实际制备了Ｍ／ＢＩＴ／ｐ－Ｓｉ、Ｍ／ＰＺＴ／ＢＩＴ／ｐ－Ｓｉ、Ｍ／ＢＩＴ／ＰＺＴ／ＢＩＴ／ｐ－Ｓｉ三种结构铁电薄膜，并测量了它们的Ｉ－Ｖ特性曲线。结果表明，夹层结构铁电薄膜Ｍ／ＢＩＴ／ＰＺＴ／ＢＩＴ／ｐ－Ｓｉ漏电流密度Ｊ最小，在５００ｎｍ厚时Ｊ＋（＋３Ｖ）约２．８×１０－１０Ａ／ｍｍ２，Ｊ－（－３Ｖ）约１．２×１０－１２Ａ／ｍｍ２优于单层和双层结构铁电薄膜的结果。     

自对准外延CoSi_2源漏接触CMOS器件技术

ＣＯ／Ｔｉ／Ｓｉ或ＴｉＮ／Ｃｏ／Ｔｉ／Ｓｉ多层薄膜结构通过多步退火技术在Ｓｉ单晶衬底上外延生长ＣｏＳｉ２薄膜，ＡＥＳ、ＲＢＳ测试显示ＣｏＳｉ２薄膜具有良好均匀性和单晶性．这种硅化物新技术已用于ＣＭＯＳ器件工艺．采用等离子体增强化学汽相淀积（ＰＥＣＶＤ）技术淀积氮氧化硅薄膜，并用反应离子刻蚀（ＲＩＥ）技术形成多晶硅栅边墙．固相外延ＣｏＳｉ２薄膜技术和边墙工艺相结合，经过选择腐蚀，可以分别在源漏区和栅区形成单晶ＣｏＳｉ２和多晶ＣｏＳｉ２薄膜，构成新型自对准硅化物（ＳＡＬＩＣＩＤＥ）器件结构．在Ｎ阱ＣＭＯＳ工艺     

激光制备多层薄膜及铁电性能的研究

利用脉冲准分子激光淀积（ＰＬＤ）方法，在Ｓｉ基片上制备了ＢＩＴ／Ｓｉ〔１００〕、ＰＺＴ／ＢＩＴ／Ｓｉ〔１００〕和ＢＩＴ／ＰＺＴ／ＢＩＴ／Ｓｉ〔１００〕铁电薄膜。用ＸＲＤ分析了多层铁电薄膜的晶相结构；用Ｓａｗｙｅｒ－Ｔｏｗｅｒ电路研究了这些单层和多层铁电薄膜的铁电性能。结果表明，单层ＢＩＴ的矫顽场Ｅｃ为４ｋＶ／ｃｍ，剩余极化强度为３．４μＣ／ｃｍ２；ＰＺＴ／ＢＩＴ的矫顽场Ｅｃ为８２ｋＶ／ｃｍ，剩余极化强度Ｐｒ为３６μＣ／ｃｍ２；ＢＩＴ／ＰＺＴ／ＢＩＴ夹层铁电薄膜的矫顽场Ｅｃ为５７ｋＶ／ｃｍ，剩余极化强度Ｐｒ为２９μＣ／ｃｍ２。最后讨论了薄膜的铁电性能与多层结构的关系     

低压反应离子镀新工艺及其设备

采用低压反应离子镀沉积技术，制备光学薄膜质量有着显著的改善。我们利用此技术沉积的ＴｉＯ２、ＳｉＯ２和Ａｌ２Ｏ３膜，其折射率分别为２５５、１４９（５５０ｎｍ）和１６７（１１００ｎｍ），比传统的电子束蒸发好得多。用此方法，在ＣＲ３９基片每面沉积４层ＴｉＯ２／ＳｉＯ２抗反薄膜，剩余反射率≤０５％。本文简要介绍其工艺过程和相应的ＬＶＲＩＰＤ装置     

Co／Ti／Si三元固相反应外延生长CoSi_2薄膜

研究采用Ｃｏ／Ｔｉ／Ｓｉ三元固相反应的方法生长外延ＣｏＳｉ２薄膜．通过选择适当的热处理条件，采用多步退火，在Ｓｉ（１００）和Ｓｉ（１１１）衬底上均成功获得外延ＣｏＳｉ２薄膜．实验用ＸＲＤ、ＴＥＭ、ＲＢＳ／ｃｈａｎｎｅｌｉｎｇ等测试技术分析ＣｏＳｉ２薄膜外延特性，得到的ＣｏＳｉ２薄膜的ＲＢＳ／ｃｈｎｎｅｌｉｎｇ最低产额Ｘｍｉｎ达到１０－１４％．实验对ＣｏＳｉ２／Ｓｉ（１１１）样品，分别沿Ｓｉ衬底的＜１１０＞和＜１１４＞晶向进行背散射沟道测量．结果发现，沿Ｓｉ＜１１０＞晶向得到的ＣｏＳｉ２背散射沟道产额显著高     

准分子脉冲激光沉积法制备的ZrO2薄膜结构和电学性能的研究

采用准分子脉冲激光沉积法 (PLD)分别在Pt/Ti/SiO2 /Si和SiO2 /Si衬底上制备了ZrO2 薄膜 ,采用扩展电阻法 (SRP)研究了薄膜纵向电阻分布 ;采用X射线衍射法 (XRD)研究了衬底温度对ZrO2 薄膜结晶性能的影响 ;精确测试了薄膜的表面粗糙度 ;讨论了薄膜结晶性能与其电学I V特性之间的关系。     

Effect of substrate porosity on photoluminescence properties of ZnS films prepared on porous Si substrates by pulsed laser deposition

ZnS films were deposited on porous Si(PS) substrates with different porosities by pulsed laser deposition. The photolumi-nescence spectra of the samples were measured to study the effect of substrate porosity on luminescence properties of ZnS/porous Si composites. After deposition of ZnS films,the red photoluminescence peak of porous Si shows a slight blueshift compared with as-prepared porous Si samples. With an increase of the porosity,a green emission at about 550 nm was observed which may be ascribed to the defect-center luminescence of ZnS films,and the photoluminescence of ZnS/porous Si composites is very close to white light. Good crystal structures of the samples were observed by x-ray diffraction,showing that ZnS films were grown in preferred orientation. Due to the roughness of porous Si surface,some cracks appear in ZnS films,which could be seen from scanning electron microscope images.     

Synthesis of the PZT films deposited on pt-coated (100) Si substrates for nonvolatile memory applications

Ferroelectric lead-zirconate-titanate (PZT) thin films were deposited by the pulsed laser deposition technique on Pt-coated (100) Si substrates. This study was focused on the investigation of the PZT film growth on (100) Si substrate at varying deposition parameters and electrical characterization of the films including hysteresis loop and fatigue properties by RT66A Standardized Ferroelectric Test System. PZT deposited at higher temperature (575°C in 450 mTorr O₂ partial pressure) showed the best crystalline structure. The remnant polarization and the retained polarization of the ferroelectric capacitors were 13 μC/cm² and 20 μC/cm², respectively. The crystallographic properties of the films were determined using the x-ray diffractometer method. The cross-sectional transmission electron microscope results showed very smooth interfaces among different layers of films.     

CeO_2高K栅介质薄膜的制备工艺及其电学性质

研究了 Ce O2 作为高 K (高介电常数 )栅介质薄膜的制备工艺 ,深入分析了衬底温度、淀积速率、氧分压等工艺条件和利用 N离子轰击氮化 Si衬底表面工艺对 Ce O2 薄膜的生长及其与 Si界面结构特征的影响 ,利用脉冲激光淀积方法在 Si(10 0 )衬底生长了具有 (10 0 )和 (111)取向的 Ce O2 外延薄膜 ;研究了 N离子轰击氮化 Si衬底表面处理工艺对 Pt/ Ce O2 / Si结构电学性质的影响 .研究结果显示 ,利用 N离子轰击氮化 Si表面 /界面工艺不仅影响 Ce O2 薄膜的生长结构 ,还可以改善 Ce O2 与 Si界面的电学性质     

激光脉冲频率对纳米Si晶薄膜形貌的影响

在气压为10 Pa的惰性气体Ar环境下,采用XeCl准分子激光器(波长308 nm),调整激光单脉冲能量密度为4 J/cm2,激光烧蚀电阻率为3000Ω.cm的高纯单晶Si靶,在玻璃或Si衬底上沉积制备了纳米Si晶薄膜。实验中靶和衬底间距离保持为3 cm,对衬底既没有加温也没有冷却。拉曼(Raman)谱测量结果表明,所制备的薄膜中已有纳米Si晶粒形成。保持脉冲总数不变,分别取激光脉冲频率为1 Hz,3 Hz,10 Hz和20 Hz,相应沉积时间约为10 min,3.3 min,1 min和0.5 min,采用扫描电子显微镜(SEM)观察所得样品的表面形貌,不同脉冲频率下的结果比较显示,脉冲频率越大,制备的纳米Si晶薄膜的平均晶粒尺寸就越小,晶粒尺寸分布也越均匀。沉积动力学过程的非线性是导致实验出现该结果的原因。     

PLD法制备高介电调谐率的纳米晶BZT薄膜

用脉冲激光沉积工艺制备了Ba(ZrxTi1-x)O3(x=0.25,0.30简称BZT25和BZT30)介电薄膜。在650℃原位退火10 min,薄膜为(111)取向柱状生长的晶粒,取向度分别为0.45和0.75。BZT25和BZT30薄膜的平均晶粒尺寸分别为50 nm和60 nm。在室温、1 MHz和3×105 V/cm条件下,BZT25的最大εr和调谐率分别达到563和65%,BZT30的最大εr和调谐率分别达到441和57%。薄膜为(111)取向生长,主要是基于薄膜与底电极Pt界面层立方相结构Pt3Ti的诱导,即(111)Pt3Ti和(111)BZT的晶格匹配。     

不同衬底温度生长的La_(0.5)Sr_(0.5)CoO_3薄膜椭圆偏振光谱研究

采用脉冲激光沉积法(PLD)在不同Si(100)衬底温度下制备了La_(0.5)Sr_(0.5)CoO_3(LSCO)导电金属氧化物薄膜.X射线衍射(XRD)分析表明,随着衬底温度升高LSCO薄膜的结晶质量增加,在650℃和700℃下制备的薄膜是具有单一钙钛矿结构的多晶薄膜.通过椭圆偏振光谱仪测量了400～1100nm波长范围内该导电金属氧化物薄膜的光学性质,采用双Lorentz振子色散关系及三相结构模型(Air/LSCO/Si)拟合获得了薄膜的光学常数.结果表明,薄膜的折射率随着衬底温度的升高而减小,然而在可见-近红外波长范围内消光系数随着衬底温度的升高而增大.这主要与薄膜的晶化质量和导电性能有密切的关系.     

High performance poly-crystalline silicon thin film transistorsfabricated using remote plasma chemical vapor deposition of SiO2

A remote plasma chemical vapor deposition (RPCVD) of SiO₂ was investigated for forming an interface of SiO₂/Si at a low temperature below 300°C. A good SiO₂/Si interface was formed on Si substrates through decomposition and reaction of SiH₄ gas with oxygen radical by confining plasma using mesh plates. The density of interface traps (D_it) was as low as 3.4×10¹⁰ cm^-2eV^-1. N- and p-channel Al-gate poly-Si TFTs were fabricated at 270°C with SiO₂ films as a gate oxide formed by RPCVD and laser crystallized poly-crystalline films formed by a pulsed XeCl excimer laser. They showed good characteristics of a low threshold voltage of 1.5 V (n-channel) and -1.5 V (p-channel), and a high carrier mobility of 400 cm²/Vs     

High-quality polycrystalline Si TFTs fabricated on stainless-steelfoils by using sputtered Si films

We have developed a low-temperature fabrication process (⩽ 200°C for high-quality polycrystalline Si thin-film transistors (poly-Si TFTs) on flexible stainless-steel foils. The fabrication processes is realized through sputter deposition of thin films, including active-Si and gate-SiO₂ films, crystallization of Si films by KrF excimer laser irradiation, and inductively coupled plasma hydrogenation. High-quality n- and p-channel poly-Si TFTs are successfully fabricated without suffering from problems of substrate bending, film ablation, or cracking in films. The resulting n- and p-channel poly-Si TFTs showed mobilities of 106 and 122 cm²/V·s, respectively. This paper describes the deposition and properties of the sputtered Si films and the fabrication process and electrical characteristics of the poly-SiTFTs     

脉冲激光溅射沉积光学增益薄膜实验研究

用脉冲激光沉积方法,以多靶交替溅射方式,在SiO2/Si基底上沉积镱铒共掺Al2O3光学薄膜,讨论了脉冲激光能量对薄膜沉积速率、表面形貌、光致发光强度的影响.在脉冲激光能量较高条件下制备出的薄膜的光致发光性能较好,脉冲激光能量较低条件下制备出的薄膜的表面形貌较均匀.综合放大器增益系数对光致发光强度和光刻工艺对薄膜表面形貌的要求,薄膜应该在合适的激光能量下制备.脉冲激光溅射沉积方法与中频磁控溅射方法相比,在抑制上转换发光方面具有优越性.