Laboratory-scale liquefiers for natural gas: A design and assessment study

Exact knowledge of natural gas composition is essential in custody transfer to determine the energy content of the delivery. However, for liquefied natural gas (LNG), a reliable composition determination is difficult. Here, we describe the design of a laboratory-scale reference liquefier that enables the validation and calibration of optical spectroscopy sensors by providing them with a sample of metrologically traceable composition. Hence, it is crucial to avoid fractionation of the sample during liquefaction. This is realized by supercritical liquefaction of a reference gas mixture in conjunction with a special vapor–liquid-equilibrium (VLE) cell. As this is a demanding high-pressure application, low-pressure condensation as liquefaction method was also assessed. Through experimental investigations and VLE calculations, preservation of the composition of the produced liquid sample during condensation was studied. We conclude that under optimized conditions, validation, and calibration measurements of optical sensors can be performed on condensed liquids, which, however, needs further confirmation.     

Experimental-numerical study and optimization of sound insulation of a finite composite cylinder

The aircraft fuselage is idealized as a composite cylinder, its vibroacoustic properties are studied both experimentally and numerically, and a minimization of the inner pressure of a composite cylinder is conducted with the genetic algorithm (GA). In the optimization, the Acoustic Transfer Vector (ATV), which comes from the boundary element method, builds the relationship between the structural surface velocity and the sound pressure at the specific filed points. Results show that the noise reduction obtained by the experimental and numerical methods have a good agreement; the optimization method which combines GA and ATV show high efficiency and robustness; increase of the bending stiffness of the cylinder can improve the noise reduction at low frequencies; both the reduction of weight and the increase of noise insulation can be achieved by the optimization of the layup at different regions of the cylinder individually.     

The performance of PCD tools in high-speed milling of Ti6Al4V

Tool performance of conventional tools is poor and a major constraint when used in milling titanium alloys at elevated cutting speeds. At these high cutting speeds, the chemical and mechanical properties of Ti6Al4V cause complex wear mechanisms. In this paper, a fine-grain polycrystalline diamond (PCD) end mill tool was tested, and its wear behavior was studied. The performance of the PCD tool has been investigated in terms of tool life, cutting forces, and surface roughness. The PCD tool yielded longer tool life than a coated carbide tool at cutting speeds above 100?m/min. A slower wear progression was found with an increase in cutting speeds, whereas the norm is an exponential increase in tool wear at elevated speeds. Observations based on scanning electron microscope (SEM) and energy dispersive spectroscopy (EDAX) analysis suggest that adhesion of the workpiece is the wear main type, after which degradation of the tools accelerates probable due to the combined effect of high temperature degradation coupled with abrasion.     

On the (un)conditionality of automatic attitude activation: The valence proportion effect.

Affective priming studies have shown that participants are faster to pronounce affectively polarized target words that are preceded by affectively congruent prime words than affectively polarized target words that are preceded by affectively incongruent prime words. We examined whether affective priming of naming responses depends on the valence proportion (i.e., the proportion of stimuli that are affectively polarized). In one group of participants, experimental trials were embedded in a context of filler trials that consisted of affectively polarized stimulus materials (i.e., high valence proportion condition). In a second group, the same set of experimental trials was embedded in a context of filler trials consisting of neutral stimuli (i.e., low valence proportion condition). Results showed that affective priming of naming responses was significantly stronger in the high valence proportion condition than in the low valence proportion condition. We conclude that (a) subtle aspects of the procedure can influence affective priming of naming responses, (b) finding affective priming of naming responses does not allow for the conclusion that affective stimulus processing is unconditional, and (c) affective stimulus processing depends on selective attention for affective stimulus information. (PsycINFO Database Record (c) 2011 APA, all rights reserved)     

Reduced percolation concentration in polypropylene/expanded graphite composites: Effect of viscosity and polypyrrole

With the goal to obtain material combining electrical and thermal conductivity at low filler loadings, composites based on polypropylenes (PP) and expanded graphite (EG) have been prepared. The effects of matrix viscosity and of coating the EG particles with polypyrrole (PPy, EG/PPy = 37.5/62.5 by weight) on the EG dispersibility and formation of percolation structures have been analyzed. When increasing the EG amount from 6 to 8 wt %, the electrical conductivity of PP/EG composites increased by 7–9 orders of magnitude, independent of matrix viscosity. When EG‐PPy is added, percolation was observed between 8 and 12 wt % EG‐PPy (3 and 4.5 wt % EG) in case of PP with higher viscosity and 6 wt % EG (2.25 wt % EG) in case of PP with lower viscosity, exhibiting a strong synergistic effect of EG and PPy in the latter case. In contrast, PPy does not contribute to reduction of thermal percolation concentration. Thermal percolation is observed at 8 wt % EG in PP/EG composites, but no percolation was found in PP/EG‐PPy composites with EG‐PPy contents of up to 20 wt %, corresponding to 7.5 wt % EG. Analyzing the melt rheology it becomes clear that the contribution of PPy to the formation of a filler network is strongly dependent on the matrix viscosity. The comparison of thermal, electrical and rheological percolation reveals that PPy participates in electron transport reducing the electrical percolation but not to heat transport. Overall, we found a good correlation between electrical, thermal, and melt rheological percolation concentrations. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41994.     

Textile fiber-reinforced anionic polyamide-6 composites. Part I: The vacuum infusion process

In order to manufacture thicker, larger and more integrated thermoplastic composite parts than currently can be achieved by melt processing, a vacuum infusion process is currently being developed at the Delft University of Technology using a reactive thermoplastic polymer called anionic polyamide-6 (APA-6). In previous studies it was demonstrated that the anionic polyamide-6 (APA-6) resin that is used has excellent mechanical properties. The present study assesses infused thermoplastic composites and focuses on fiber-matrix interactions. Part I of this study focuses on the thermal effects, causes for deactivation of the initiator and the restriction caused by the low in-plane permeability of the fiber textiles on various transport phenomena. It will be shown that addition of pre-heated fibers not only shortens the infusion window, but also influences the matrix properties by reducing the exothermic heat production. In addition, the low in-plane permeability of the fiber textiles influences the infusion time and causes the entrapment of voids. Finally, reactions between the matrix and the fiber surface can lead to deactivation of the initiator and bond formation with the activator. Interfacial bonding, however, is discussed in more detail in Part II of this study, whereas the effect of adding a nucleating agent is discussed in Part III.     

THE IMPACT OF CHANGING BUSINESS AGGLOMERATION ECONOMIES ON METROPOLITAN GROWTH

ABSTRACT This paper aims to determine the impact of changes in the parameters measuring economies of scale in production on metropolitan growth. The degree of spatial concentration of sectoral economic activity and patterns of trade between two metropolitan areas are explained with a two-sector model borrowed from the international trade literature. It is shown that sectoral production will become more concentrated as the importance of intrasectoral economics of scale relative to intersectoral scale economics increases. An increase in the relative size of intrasectoral business agglomeration economics will not necessarily lead to complete specialisation by either metropolitan area.     

Analysis of electrocardiograms during atrial fibrillation

The research discussed in this article is motivated by the search for an optimal classification of the different types of atrial fibrillation (AF) on the basis of recorded atrial signals. This would facilitate the selection of an optimal therapy. This article focuses on the biophysical models of the genesis of ECG waveforms during AF. The model of the electric activity of the atria was found to have sufficient realism to be used to describe the electric sources during AF. The inclusion of the volume conduction model resulted in electrocardiographic signals that are in all aspects similar to those observed clinically. The model is currently applied to solve various problems related to optimal signal preprocessing and extraction of features in AF signals for the classification of AF abnormalities. The biophysical model of the atrial activity is an essential element in this research, since it is capable of describing the electric source specifications derived from different hypotheses relating to the etiology of AF