载气在CVD法制备纳米碳管工艺中的作用

纳米碳管是性能优异的具有准一维特征的纳米材料,CVD法是制备纳米碳管的典型工艺之一。本文以乙炔气体为原料气体、循环失效后的贮氢电极舍金材料作为反应催化剂,研究了在相同反应条件下,CVD法制备纳米碳管过程中载气对纳米碳管形貌和产率的影响。通过对产物TEM观察和TG分析发现,虽然载气不直接参与合成反应但对产物产率和形貌有很大的影响,氢气作为载气可以获得形貌和热稳定性更好的纳米碳管。     

纳米碳管中离散分布的金属Ni纳米线气-液/固-固填充模型

以Ni∶Cr=3∶1的双金属层作为催化剂,用C2H2为碳源气体利用化学气相沉积(CVD)法,在不同的温度下制备纳米碳管.扫描电子显微镜(SEM)和透射电子显微镜(TEM)研究制备产物发现:当制备温度高于900℃时,没有纳米碳管生成,制备温度在700～800℃之间纳米碳管中填充有一些离散分布的金属Ni纳米线,制备温度在650℃有纳米碳管生成,但是纳米碳管中没有发现纳米线的填充.通过高分辨透射电子显微镜(HRTEM)分析发现,纳米线是以液态或是粘滞液态填充进纳米碳管.根据实验结果,提出了一个在本实验条件下纳米线填充进纳米碳管的气-液/固-固V- L/S -S(vapor- liquid/solid-solid)模型,这个模型能解释一些传统的V-L-S(vapor- liquid -solid)模型不能解释的实验现象.     

一种基于CVD法的纳米碳管微观分析及场致发射特性的研究

将化学气相沉积法（CVD）制备的纳米碳管提纯后，用透射电镜（TEM）观测了它的微观结构，通过实验对纳米碳管在不同温度下生长的结构特性进行了分析比较，得出了纳米碳管生长的最佳温度为750℃；并对纳米碳管粉体的拉曼（Raman）光谱进行了分析，得到了与透射电镜观测相一致的结论；最后测试了纳米碳管的场致发射特性．     

多壁纳米碳管的制备与表面改性处理

以Co-MCM-41作催化剂,采用化学气相沉积(CVD)法催化热解无水乙醇制备纳米碳管(CNTs),然后将纳米碳管在120℃下用浓硝酸回流,进行纯化及表面酸氧化改性处理。通过XRD、FT-IR、TEM、N2吸附-脱附和Raman光谱等分析手段对酸处理前后的纳米碳管进行了表征。结果表明制备出品质较好、管径均匀、管壁较厚、顶端开口的多壁纳米碳管。浓硝酸氧化处理后在纳米碳管的表面存在羧基和羟基等官能团。     

定向纳米碳管微观结构的观察和生长机制探讨

SiO2表面溅射铁膜后用CVD法制备了定向纳米碳管。用扫描电镜、透射电镜和高分辨透射电镜对顶部催化剂及包裹于管内的催化剂、纳米碳管的结构和所形成的竹节状形貌进行了观察。以液态生长纳米碳管为基础提出了一种纳米碳管生长机制。     

失效AB5型贮氢合金电极材料在制备纳米碳管中的应用

纳米碳管是一种性能优异的新型功能材料.利用循环失效后的AB5型贮氢合金电极材料作为反应催化剂、乙炔气体作为原料气体通过CVD法制备出多壁纳米碳管,研究了经过破碎、清洗、氧化处理后的失效AB5型贮氢合金电极材料在合成纳米碳管中的催化性能,讨论了不同氧化温度处理催化剂对纳米碳管产率、形貌和结构稳定性的影响.结果表明,氧化处理温度对催化剂的催化效能有明显的影响,600℃为最佳氧化处理温度.以氧化处理后的失效AB5型贮氢合金电极材料作为催化剂制备碳纳米管,方法简单易行,为废旧镍氢电池负极材料的回收再利用提供了一种新的思路.     

CVD法工业化生产纳米碳管的研究

以乙炔为原料气,用工业化生产炉代替小型实验研究炉批量制备出了纳米碳管,产量为150g/h。TEM图和Raman光谱结果表明,纳米碳管管径均匀分布在20～30 nm间,具有很高的石墨化程度。同时,讨论了生产炉结构、工艺参数以及裂解温度、裂解时间和原料气流量对纳米碳管的影响。     

CVD法工业化生产纳米碳管的研究

以乙炔为原料气,用工业化生产炉代替小型实验研究炉批量制备出了纳米碳管,产量为150g/h.TEM图和Raman光谱结果表明,纳米碳管管径均匀分布在20～30 nm间,具有很高的石墨化程度.同时,讨论了生产炉结构、工艺参数以及裂解温度、裂解时间和原料气流量对纳米碳管的影响.     

碳化硅纳米线的制备及表征

以化学气相沉积法制备的纳米碳管粗产物和各向同性煤沥青为原料,采用热压成型工艺制备了纳米碳管/沥青复合材料,复合材料经1600℃高温热处理产物中生成了纤维状碳化硅(SiC)纳米线。扫描和透射电子显微分析表明所制备的SiC纳米线表面较为光洁,长度约为几个微米,直径约为30~80nm。二次电子像及其能谱分析表明原料中的金属镍颗粒和纳米碳管对SiC纳米线的生长具有重要作用。     

CVD宏观量半连续制备纳米碳管的研究

研究了以乙炔为基本原料,用Ｎ_２做载流气体;以纳米钻颗粒为催化剂在７００～８００℃常压下纳米碳管的宏观量制备．粗产品中纳米碳管的含量接近５０％,而且纳米碳管缺陷很少,直而长,石墨化好．纳米碳管的形核过程是因为碳在催化剂表面分布不均匀造成的．纳米碳管的生长极限在１５ｍｉｎ左右,然后生长变得缓慢,纳米碳管的一般长度在５～３０μｍ．     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.