碳化硅纳米线的制备及表征

以化学气相沉积法制备的纳米碳管粗产物和各向同性煤沥青为原料,采用热压成型工艺制备了纳米碳管/沥青复合材料,复合材料经1600℃高温热处理产物中生成了纤维状碳化硅(SiC)纳米线。扫描和透射电子显微分析表明所制备的SiC纳米线表面较为光洁,长度约为几个微米,直径约为30~80nm。二次电子像及其能谱分析表明原料中的金属镍颗粒和纳米碳管对SiC纳米线的生长具有重要作用。     

氨气氛中镍催化剂和纳米碳管的制备

用X射线衍射仪、扫描电子显微镜和透射电子显微镜,研究了以瓷舟为载体、硝酸镍为原料、乙炔为碳源,在氨气中制备镍催化剂和纳米碳管时温度的影响,并讨论了氨气的作用.结果表明,以氨气还原硝酸镍获得镍催化剂时,最佳温度范围是700～800℃,此时催化剂的颗粒较细小且均匀,有利于纳米碳管的生长;此外,选用孔径比较细小均匀多孔的载体材料,有助于获得颗粒均匀细小的镍催化剂;在制备纳米碳管时,热分解氨得到的活性氢原子有利于维持催化剂的活性,抑制无定型碳的生成,从而促进纳米碳管生长.实验中纳米碳管的最佳制备温度为700～800℃,管径为10～25nm.     

大规模制备Ni纳米线阵列及其磁学特性研究

在多孔氧化铝模板的纳米孔洞中,利用直流电化学沉积的方法成功地制备了高度有序的磁性金属Ni纳米线阵列.利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射仪(XRD)和物理性质测量系统(PPMS)对样品的形貌、晶体结构和磁学性能进行了表征测试.SEM和TEM观察结果显示,Ni纳米线均匀地生长在氧化铝模板的孔洞中,直径约为300nm,其表面非常光滑.XRD结果显示,生长的Ni纳米线为fcc结构.磁测量结果表明,与体材料相比,Ni纳米线展现出增强的矫顽力和剩磁比,并且表现出较强的磁各向异性,其居里温度约为627K,与块体Ni的居里温度相当,说明在较高温度下,纳米线仍可呈现铁磁特性.     

纳米碳管/环氧树脂复合材料的制备及力学性能

报道了利用催化裂解法制备的纳米碳管合成环氧树脂复合材料的技术及工艺条件。利用透射电子显微镜(TEM)对制备的复合材料进行观察表征;通过拉伸及压缩实验对纳米碳管/环氧树脂复合材料的力学性能进行了测试。实验结果表明:纳米碳管的加入可以明显地改变环氧树脂基体材料的力学性能。      

溶胶-凝胶法制备硼酸镁纳米棒

以硝酸镁、硼酸、柠檬酸为原料, 利用溶胶-凝胶法及不同温度后续煅烧制备了硼酸镁(MgB₄O₇和Mg₂B₂O₅)纳米棒. 用X射线衍射(XRD)分析了纳米棒的结构, 用扫描电子显微镜(SEM)和透射电子显微镜(TEM)观察了纳米棒的形貌. 实验结果表明, 750℃煅烧产物为MgB₄O₇纳米棒, 950℃煅烧产物为Mg₂B₂O₅纳米棒, 纳米棒的径长比可以通过调节原料硝酸镁和硼酸的比例来控制. 用自催化机理解释了硼酸镁纳米棒的生长机理.     

复合锌镍纳米线结构和磁性研究

采用直流电化学沉积方法,在多孔阳极氧化铝模板纳米孔洞中制备出直径约90nm,长度超过10μm的金属Ni/Zn纳米线有序阵列.通过扫描电子显微镜(SEM),透射电子显微镜(TEM),原子力显微镜(AFM),X射线衍射仪(XRD),振动样品磁强计(VSM)对模板及所制备的样品进行形貌、结构及相关性能的表征和测试.结果表明所制备的Ni/Zn纳米线具有沿[111]方向择优生长特性,易磁化方向沿纳米线长轴方向.     

氨化Si基Ga2O3/V薄膜制备GaN纳米线

为了制备高质量的GaN纳米结构,采用磁控溅射技术先在硅衬底上制备Ga2O3/V薄膜,然后在流动的氨气中进行氨化反应,成功制备出GaN纳米线.采用X射线衍射(XRD)、傅里叶红外吸收光谱(FTIR)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对样品进行分析.研究结果表明,采用此方法得到了六方纤锌矿结构的GaN纳米线,且900℃时制备的纳米线质量最好,直径在60nm左右,长度达到十几微米.     

生长温度对热蒸发法制备ZnO纳米线的结构与发光性能影响

采用无金属催化剂的简单热蒸发法,在Si(100)衬底上不同生长温度下成功地制备了高密度和大长径比的单晶ZnO纳米线。分别利用X射线衍射仪(XRD)、扫描电子显微镜(SEM-EDS)、透射电子显微镜(TEM)及荧光光谱仪表征样品的结构和发光性质。XRD和TEM研究表明,所制备的样品为沿c轴择优取向生长的单晶ZnO纳米线,具有六方纤锌矿结构。SEM和TEM研究表明,生长温度对ZnO纳米线的形貌及长径比的影响较大。当生长温度为700℃时,制备得到长径比为300(长度约为15μm,直径约为50nm)的ZnO纳米线;低于600℃时,形成花状ZnO纳米锥或纳米棒;高于700℃时,形成小长径比的ZnO纳米棒。此外,室温光致发光(PL)谱上出现一个强而尖锐的紫外发射峰以及一个弱而宽泛的蓝光发射峰。采用的热蒸发法制备ZnO纳米线基于气-固(VS)生长机理且该生长方法可用于大规模、低成本制备高纯度的单晶ZnO纳米材料。     

氨化Si基Ga2O3/Ti制备GaN纳米线

采用磁控溅射技术先在硅衬底上制备Ga2O3/Ti薄膜,然后在950℃时于流动的氨气中进行氨化反应制备GaN薄膜.X射线衍射(XRD)、傅立叶红外吸收光谱(FTIR)、选区电子衍射(SAED)和高分辨透射电子显微镜(HRTEM)的结果表明采用此方法得到了六方纤锌矿结构的GaN单晶纳米线.通过扫描电镜(SEM)观察发现纳米线的形貌,纳米棒的尺寸在50～150nm之间.     

液-固-溶液法制备ZnSe:Fe纳米晶及其光学性能研究

采用液-固-溶液(LSS)法制备了ZnSe:Fe纳米晶,利用X射线粉末衍射(XRD)技术、透射电子显微镜(TEM)、光致发光(PL)谱、紫外-可见吸收(UV-vis)光谱以及傅里叶变换红外(FT-IR)光谱对所制备样品的结构和光学性质进行了表征,研究了掺杂Fe离子对ZnSe纳米晶光学性质的影响规律.实验结果表明所制备的...     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.