综合设计性实验在药物分析学实验中对学生综合能力的培养

《药物分析学实验》是药学专业的一门独立必修课程,是药学科学领域中的一个重要组成部分,具有较强的实践性和综合性,旨在培养学生综合运用所学知识分析药品质量的能力.综合设计性实验作为《药物分析学实验》的重要组成部分,对学生实践操作能力,发现问题、分析问题、解决问题的能力,创新能力,应用能力,团结协作能力,劳动素养等综合能力的培养具有极其重要的意义.     

Aluminum based reflective nanolens arrays to improve the effectiveness of ultraviolet inactivation of Escherichia coli O157:H7 and Listeria monocytogenes in water and a sucrose solution

Food Science and Biotechnology - Aluminum based reflective nanolens arrays were developed via a series of aluminum electropolishing and anodization steps with subsequent selective dissolution of...     

Preparation and characterization of mullite whisker reinforced ceramics made from coal fly ash

Ceramics with mullite whiskers were prepared from coal fly ash and Al₂O₃ raw materials, with AlF₃ used as an additive. The phase structures and microstructures of the ceramics were identified via X-ray diffraction and scanning electron microscopy, respectively. The results show that pickling of coal fly ash is an effective method for enhancing the flexural strength of ceramics. Sintering temperature and AlF₃ addition were also key factors influencing the creation of ideal ceramics. The ceramic made from pickled coal fly ash, 6?wt% AlF₃, and sintered at 1200?°C, exhibited the highest flexural strength of 59.1?MPa, and had a bulk density of 1.32?g/cm³ and porosity of 26.8%. The results show that ceramic materials made under these conditions are ideal candidates for manufacturing ceramic proppants for the exploitation of unconventional oil and gas resources.     

SUBSCRIPTION 2018

正Four issues per volume a year,CHINA’S REFRACTORIES is distributed worldwide by airspeed delivery at no extra cost to subscribers.     

Effect of coupling agent content on properties of composites made from polylactic acid and chrysanthemum waste

Chrysanthemum flower is among one of the highly sought after and widely planted flower crops, in particular for cultural and religious ceremonies. However, the chrysanthemum stem and stalk have little value and usually discard as by‐product waste from floristry. The objective of this research is to investigate the potential value of utilizing chrysanthemum stem and stalk as reinforcing fillers for thermoplastic composites. In this study, 2‐mm thick composite sheet containing predefined formulations of polylactic acid (PLA), chrysanthemum waste filler (CWF) ranging from 15 to 60 phr, and maleated polyethylene (MAPE) coupling agent up to 5 phr were prepared with the aid of Haake internal mixer and compression molding. The effect of MAPE loading on tensile, thermal, and morphological properties of PLA/CWF composites was investigated. The findings revealed that PLA/CWF composite attained improved tensile modulus compared to the neat PLA, and the tensile modulus increases with higher concentration of CWF. However, both tensile strength and elongation at break reduces with increase loading of CWF. Overall, PLA/CWF composites with MAPE shows better performance compared to those without MAPE, where an optimum strength of 21.8 MPa can be achieved with 60 phr CW and 3 phr MAPE. The measured tensile strength is comparable to alternatives natural fiber thermoplastic composites demonstrating its potential to be used in non‐structurally demanding application. J. VINYL ADDIT. TECHNOL., 26:10–16, 2020. © 2019 Society of Plastics Engineers     

器外预硫化型MoNiP/γ-Al2O3催化剂的加氢脱硫性能研究

以二苯并噻吩为模型化合物，研究了器外预硫化型加氢催化剂MoNiP／γ-Al2O3的加氢脱硫初始活性及其储存稳定性。结果表明，使用不同配方的硫化剂，在反应温度160℃、浸渍温度160℃、浸渍时间4h、氮气热处理温度300℃的条件下制备得到的器外预硫化催化剂的加氢脱硫活性较好，部分可以达到器内预硫化催化剂的效果，但其加氢活性稍弱；二苯并噻吩在器内与器外预硫化催化剂上的加氢脱硫反应的历程类似，但是对于器外预硫化催化剂而言，二苯并噻吩的加氢脱硫主要依赖于氢解历程。器外预硫化催化剂的储存稳定性较好，长期储存后仍可以维持较高的HDS活性。     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

多变量自校正解耦控制器的全局收敛性分析

本文对多变量自校正解耦控制算法[1]进行了稳定性和收敛性分析.结果表明:该算法 即使用于非最小相位系统仍然具有全局收敛特性,即以概率l输入输出向量采样均方有界, 广义跟踪误差向量条件采样均方极小.     

掺钛蓝宝石激光晶体中夹杂物的分析

本文用大视场光学显微镜、电子探针观察和分析了掺钛蓝宝石激光晶体中夹杂物的形状、尺寸大小及元素组成，并提出消除和减少这些夹杂物的方法．