Assessment of Dewatering Requirements and Dewatering Well Design for an Open Pit Coal Mine in Central Anatolia

The Çeltikçi Coal Basin is a newly discovered coal basin in Central Anatolia where 11 years of open-cut mining has been planned. The bulk of the mining will be conducted below the regional water table; hence, determination of the dewatering requirements and proper design of the dewatering wells plays a critical role. This study (i) defined the dewatering requirements of the open-pit mine, (ii) established a dewatering well design for the area, and (iii) assessed the anticipated impacts of the dewatering activities. For this purpose, a 3-D numerical groundwater flow model was developed using the FEFLOW software. Yearly dewatering requirements were determined under transient conditions. For the dewatering well simulations, two types of dewatering wells were considered: permanent wells located at the open pit boundary that would increase in number as the excavation proceeds and wells located at the periphery of the yearly excavated area that would be operational for about two years. The simulation results indicated that 894 wells were required to satisfy dry working conditions; the average pumping rate throughout the mine life was calculated as 322 L/s. The impacts of open-pit dewatering on groundwater resources were assessed in terms of spring discharge and base flow rates in the nearby Kirmir stream. As a result of dewatering, most of the village water supply springs and fountains will dry up in the area. In addition, the base flow rates to the Kirmir stream will be decreased by 15%.

     

Development and characterization of poly(vinyl alcohol) and casein blend films

Blends of plasticized casein (CA) and poly(vinyl alcohol) (PVA) at various ratios were prepared using the solution‐casting method. The prepared blend solutions were cast onto polystyrene petri plates and bend films were obtained. The characterization of films was performed using Fourier transform infrared spectroscopy, tensile testing, thermogravimetric analysis, contact angle measurements and water vapour permeability. According to spectroscopic analysis, there were interactions between the CA and PVA molecules. The tensile test results showed that the tensile strength of CA increased with increasing PVA content. The flexibility of plasticized CA film increased with the incorporation of PVA. The thermal stability and water vapour barrier properties of plasticized CA improved on blending with PVA. As a result, it was seen that blend films were successfully produced using plasticized CA and PVA with potential for use in biodegradable packaging applications. © 2019 Society of Chemical Industry     

Electrospun fiber membranes from blends of poly(vinylidene fluoride) with fouling‐resistant zwitterionic copolymers

Nonwoven super‐hydrophobic fiber membranes have potential applications in oil–water separation and membrane distillation, but fouling negatively impacts both applications. Membranes were prepared from blends comprising poly(vinylidene fluoride) (PVDF) and random zwitterionic copolymers of poly(methyl methacrylate) (PMMA) with sulfobetaine methacrylate (SBMA) or with sulfobetaine‐2‐vinylpyridine (SB2VP). PVDF imparts mechanical strength to the membrane, while the copolymers enhance fouling resistance. Blend composition was varied by controlling the PVDF‐to‐copolymer ratio. Nonwoven fiber membranes were obtained by electrospinning solutions of PVDF and the copolymers in a mixed solvent of N,N‐dimethylacetamide and acetone. The PVDF crystal phases and crystallinities of the blends were studied using wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). PVDF crystallized preferentially into its polar β‐phase, though its degree of crystallinity was reduced with increased addition of the random copolymers. Thermogravimetry (TG) showed that the degradation temperatures varied systematically with blend composition. PVDF blends with either copolymer showed significant increase of fouling resistance. Membranes prepared from blends containing 10% P(MMA‐ran‐SB2VP) had the highest fouling resistance, with a fivefold decrease in protein adsorption on the surface, compared to homopolymer PVDF. They also exhibited higher pure water flux, and better oil removal in oil–water separation experiments. © 2018 Society of Chemical Industry     

Cocaine Induces Cytoskeletal Changes in Cardiac Myocytes: Implications for Cardiac Morphology

Cocaine is one of the most widely abused illicit drugs worldwide and has long been recognised as an agent of cardiac dysfunction in numerous cases of drug overdose. Cocaine has previously been shown to up-regulate cytoskeletal rearrangements and morphological changes in numerous tissues; however, previous literature observes such changes primarily in clinical case reports and addiction studies. An investigation into the fundamental cytoskeletal parameters of migration, adhesion and proliferation were studied to determine the cytoskeletal and cytotoxic basis of cocaine in cardiac cells. Treatment of cardiac myocytes with cocaine increased cell migration and adhesion (p < 0.05), with no effect on cell proliferation, except with higher doses eliciting (1–10 μg/mL) its diminution and increase in cell death. Cocaine downregulated phosphorylation of cofilin, decreased expression of adhesion modulators (integrin-β3) and increased expression of ezirin within three hours of 1 μg/mL treatments. These functional responses were associated with changes in cellular morphology, including alterations in membrane stability and a stellate-like phenotype with less compaction between cells. Higher dose treatments of cocaine (5–10 μg/mL) were associated with significant cardiomyocyte cell death (p < 0.05) and loss of cellular architecture. These results highlight the importance of cocaine in mediating cardiomyocyte function and cytotoxicity associated with the possible loss of intercellular contacts required to maintain normal cell viability, with implications for cardiotoxicity relating to hypertrophy and fibrogenesis.     

Flexible poly(styrene-ethylene-butadiene-styrene) hybrid nanofibers for bioengineering and water filtration applications

Among the thermoplastic elastomers that play important roles in the polymer industry due to their superior properties, styrene-based species and polyurethane block copolymers are of great interest. Poly(styrene-ethylene-butadiene-styrene) (SEBS) as a triblock copolymer seems to have the potential to meet many demands in different applications due to various industrial requirements where durability, biocompatibility, breaking elongation, and interfacial adhesion are important. In this study, the SEBS triblock copolymer was functionalized with natural (Satureja hortensis, SH) and synthetic (nanopowder, TiO₂) agents to obtain composite nanofibers by electrospinning and electrospraying methods for use in biomedical and water filtration applications. The results were compared with thermoplastic polyurethane (TPU) composite nanofibers, which are commonly used in these fields. Here, functionalized SEBS nanofibers exhibited antibacterial effect while at the same time improving cell viability. In addition, because of successful water filtration by using the SEBS composite nanofibers, the material may have a good potential to be used comparably to TPU for the application.     

Efficient manganese decorated cobalt based catalysts for hydrogenation of 5-hydroxymethylfurfural (HMF) to 2,5-dimethylfuran (DMF) biofuel

2,5-dimethylfuran (DMF) is a promising compound in the production of biofuel with high-quality properties. In this study, it is aimed to develop new efficient catalysts to synthesize DMF from 5-hydroxymethylfurfural (HMF). Co, Mn/Co, and Ru/Co catalysts were prepared using the NaBH₄ reduction method. The catalysts were subjected to activity tests for the hydrogenation of HMF to DMF by changing the reaction parameters, such as temperature and time. Mn/Co catalysts prepared from metal precursors at various molar ratios of Mn/Co were found to be effective in hydrogenation reactions of HMF to DMF. A 91.8% DMF yield was achieved in the presence of a Mn/Co (50/50) catalyst without noble metal at 180°C for 4 hours. The Brunauer-Emmet-Teller (BET) method, x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), and induction coupled plasma mass spectroscopy (ICP-MS) techniques were used to characterize the efficient Mn/Co catalyst.