Lanxide Al/Al2O3陶瓷基复合材料的显微结构研究

本文利用XRD、EPMA,SEM等分析方法对Lanxide技术制备的Al/Al₂O₃复合材料的显微结构进行了研究。结果表明,Lanxide Al/Al₂O₃材料是以三维连通骨架状α-Al₂O₃为基体的陶瓷基复合材料,网状或点块状金属相(Al、Si)和孔洞相分布于Al₂O₃晶间或晶粒内。改变工艺对材料的组织和性能有较大影响。     

烧成温度对Al2O3/Ni复合材料的致密化、物相组成和显微结构的影响

首先采用非均相沉淀合成出Ni包裹Al₂O₃粉体,然后热压烧结包裹粉体制备了Al₂O₃/Ni复合材料。本文作者主要研究了不同烧成温度对复合材料致密化、物相组成和显微结构的影响。结果表明:在1400℃保温1h,烧结体获得了最大相对密度,而致密度随Ni含量的增加反而降低;高于1350℃时,除Al₂O₃和Ni相外,在烧结体的表层生成一种由Al,Ni,O,C四种元素组成的新相;随着温度的升高,包裹层的纳米Ni颗粒聚合、长大,并退缩至三角晶界处,在适当的烧结温度(1400℃),少数小的纳米Ni颗粒被卷入Al₂O₃晶内,大的位于三角晶界,当烧成温度为1450℃时,不仅观察到Al₂O₃/Ni界面存在空隙,也发现了Al₂O₃晶粒异常长大现象。     

纳米-Al2O3/SiO2加入量对MgO-Al2O3-SiO2复相陶瓷烧结机理的影响

为了探究纳米-Al₂O₃/SiO₂加入量对MgO-Al₂O₃-SiO₂复相陶瓷烧结行为的作用机理。以微米级MgO、纳米级Al₂O₃和SiO₂为主要原料制备陶瓷基复合材料。通过XRD和 SEM等检测手段对烧后试样的物相组成和微观结构进行测试与表征,重点研究Al₂O₃/SiO₂的加入对复相陶瓷物相组成、微观结构及烧结性能的影响。结果表明:随着Al₂O₃/SiO₂加入量的增大,试样烧后相对密度和烧后线变化率呈先增大后减小再增大的趋势,加入15%Al₂O₃/SiO₂(质量分数)的试样经1 500 ℃烧结后,其相对密度可以达到94%。引入的Al₂O₃/SiO₂与基体中的MgO生成镁铝尖晶石与镁橄榄石相,原位反应伴随的体积膨胀,抵消部分烧结过程中的体积收缩。Al₂O₃/SiO₂加入量为75%(质量分数)的试样经1 400 ℃烧结后,基体中有大量堇青石相生成,随着煅烧温度提高到1 500 ℃,堇青石分解所产生的高温液相促进了试样的烧结收缩。     

纳米Al2O3颗粒增强新型铜基自润滑复合材料

以Cu-Ni-Y₂O₃-MoS₂-Graphite混合粉为基体,加入质量分数分别为0%、1%、2%、3%、4%的纳米Al₂O₃增强相,采用粉末冶金方法制备纳米Al₂O₃增强新型铜基自润滑复合材料。结果表明：随着铜合金粉末中纳米Al₂O₃颗粒含量的增加 , 所制备自润滑复合材料样品的密度下降,但硬度和压溃强度先上升后下降,在Al₂O₃含量为2%时硬度从HV 23.7增加到HV 35.1,压溃强度从189 MPa提高到276 MPa。由石墨和MoS₂组成的混合固体自润滑材料的摩擦系数小且稳定,约0.12。Al₂O₃质量分数为2%的样品磨损量最小,是未加Al₂O₃试样磨损量的1/7～1/8。铜基体经过镍、纳米Al₂O₃等弥散颗粒强化和固体润滑相石墨和MoS₂的加入,所制备的材料已具有一定的自润滑性能。     

Al2O3颗粒粒径和含量对α-Al2O3/Cu复合镀层性能的影响

本文研究了复合电沉积法制备的α-Al₂O₃/Cu 复合材料的性能和磨损特征, 测定了Al₂O₃粒径在0. 5～ 5Lm, 含量在4～ 16% 时Al₂O₃/Cu 复合镀层的硬度和磨损率, 用扫描电镜对磨损形貌进行了分析, 并对其磨损机制进行了探讨。结果表明, 镀层中硬度随Al₂O₃含量增加呈线性增长, 且含大颗粒Al₂O₃镀层的硬度略高于小颗粒镀层,Al₂O₃颗粒含量和粒径大小对磨损率和磨损机制有显著影响。     

原位Al2O3片晶/Ce-TZP和SrO·6Al2O3棒晶/Ce-TZP复合材料的制备与显微结构

通过在Ce-TZP基体中加入AlOOH及矿化剂TiO₂或反应剂SrCO₃制备了原位Al₂O₃片晶/Ce-TZP复合材料和原位SrO·6Al₂O₃棒晶/Ce-TZP复合材料。在烧结过程中TiO₂促进Al₂O₃晶粒发生显著的各向异性生长原位生成的片晶、Al₂O₃与SrCO₃发生反应,原位生成的高度各向异性的棒晶,它们在基体中分布均匀,具有较大的纵横比。烧结温度对片晶/棒晶的大小和含量有明显影响。通过在基体中原位形成片晶或棒晶,材料的力学性能有明显的改善。     

Al2O3颗粒增强纯铝基复合材料的研究

本文探讨了用粉末冶金法,采用常规的冶金加工设备和工艺,制造Al₂O₃颗粒增强纯铝基复合材料的可行性。研究了不同Al₂O₃体积含量复合材料的显微组织及力学性能。初步试验了二次热挤压变形对颗粒分布和对基体强化的影响。结果表明,Al₂O₃颗粒与纯铝粉混合,加压烧结制备的复合材料,组织致密,颗粒分布均匀,随Al₂O₃含量增加,复合材料强度、硬度及弹性模量大大提高,Al₂O₃含量小于10%时,塑性不降低。二次热挤压有助于提高颗粒分布的均匀性;并使基体显著强化。     

反应烧结法制备(AlN,TiN)-Al2O3复合材料的研究

以Ti,Al,Al₂O₃为初始粉料,通过750~800℃氮气保护下的中温焙烧,然后在1420~1550℃在氮气氛下反应烧结,制备了不同配比的(AlN,TiN)-Al₂O₃复合材料。研究了组成及烧结工艺对复合材料力学性能、显微结构等的影响。用XRD,SEM等方法分析粉体及烧结体的相组成及微观结构。分析结果表明:AlN,TiN的形成,有助于材料的致密化并使其力学性能提高。组成为20wt%(Al,Ti)-Al₂O₃的粉体在1520℃、30MPa、保温、保压30min热压烧结条件下,与N₂气反应可得到硬度(HRA)为 94.1的高硬度的(AlN,TiN)-Al₂O₃复合材料,该材料的抗弯强度为687 MPa,断裂韧性(K_IC)为6.5MPa·m1/2。     

新型陶瓷基复合超疏水涂层的制备及其性能

为了研究开发新型超疏水涂层的制备方法,改善涂层的结构与性能,以Al₂O₃-40%TiO₂(AT40)、PFA(全氟烷氧基乙烯基醚共聚物)粉末为原始材料,采用大气等离子喷涂(APS)技术,并调整电流、氩气流量等喷涂参数,在铝合金基体表面制备了两种不同的AT40/PFA复合超疏水涂层。利用相对应的测试仪器及分析手段对喷涂态涂层的相组成、显微结构、摩擦系数及基本性能等进行了表征分析。结果表明,两种涂层的相组成均为C₂₀F₄₂、Al₂TiO₅及少量的γ-Al₂O₃、α-Al₂O₃相;涂层表面均为圆形和椭圆形的粒状突起结构,其中突起结构的表面均存在类似荷叶表面结构的二元微纳米乳突结构,其表面粗糙度为9.3 μm和12.41 μm;所得涂层具有良好的综合性能,与水的静态接触角均达到了150°以上,滚动角为4~5°;在其他参数不变的情况下,随着电流的增大及氩气流量的减小,涂层中的陶瓷相含量增加,涂层的粗糙度、摩擦系数、显微硬度及结合强度均增大。     

陶瓷颗粒增强镍合金复合涂层冲蚀磨损的试验研究

以WC,ZrO₂,Cr₂O₃和Al₂O₃陶瓷颗粒为增强相,镍合金粉末为基体,运用等离子喷涂技术制备四种陶瓷/镍合金复合涂层。采用冲蚀磨损试验机和正交试验方法,进行陶瓷颗粒相浓度、磨粒粒度、冲蚀角和速度对陶瓷颗粒/镍合金复合涂层抗冲蚀磨损性能影响的试验研究。采用表面形状测量仪对陶瓷颗粒/镍合金复合涂层磨损表面形貌进行测量和分析。试验结果得到WC,ZrO₂,Cr₂O₃和Al₂O₃四种陶瓷颗粒/镍合金复合涂层冲蚀磨损率的经验关联式。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.