直接检测光正交频分复用系统一阶偏振模色散研究

基于直接检测的光OFDM系统(DDO-OFDM),实现简单、成本较低,对未来高速光传输具有重要的借鉴价值。而在高速传输中,偏振效应带来OFDM信号展宽及输出偏振态的不同,严重影响系统传输性能。对DDO-OFDM系统中的一阶偏振模色散(PMD)作用机理和数学模型进行分析,结果表明,DDO-OFDM系统中一阶PMD仅对OFDM信号子载波信号幅度附加余弦因子,通过信道均衡,可有效去除此噪声影响,差分群时延为50ps条件下,以10Gb/s的速率在单模光纤传输800km,DDO-OFDM系统Q值为16dB,较色度色散影响下系统性能仅有0.3dB降低。     

通过恒包络调制提高相干光OFDM系统的光纤非线性容限

相干光正交频分复用(CO-OFDM)对光纤链路中 的色度色散(CD)和偏振模色散(PMD)具有较强的容忍性,但 是OFDM信号高峰均功率比(PAPR)的特点使其对光纤非线性效应 非常敏感,严重影响了系统传输性能。 本文提出了基于恒包络(CE)调制的方法使得系统中光信号PAPR降低为0dB,从而提高了CO-OFDM系统的非 线性传输性能。仿真结果表明,子载波采用16QAM调制的40Gbit/s单信道CE调制CO -OFDM系统,在经800km无色散补偿、欠色散补偿和周期全色散补偿 标准单模光纤(SSMF)链 路传输后,虽然较传统CO-OFDM存在约1.8dB的代价,但是系统最大 发射光功率分别提高 了6.2、9.3dB。并且,将本文方案应 用 到CO-OFDM和10Gbit/s NRZ-OOK混合传输WDM系统中,信道最大发 射光功率仍获得了5.2dB的提高。因此,本文提出的CE调制方法能有 效地提高CO-OFDM系统在不同传输环境中的光纤非线性容限。     

相干光正交频分复用系统偏振模色散研究

相干光正交频分复用系统(Coherent Optical Orthogonal Frequency Division Multiplexing,CO-OFDM)具有良好的色散抑制性能及简单有效的信号均衡算法,是近年来光传输领域的研究热点之一。偏振模色散严重影响高速传输,色散均衡复杂,计算负荷较大。文章介绍了一种基于偏振复用(Polarization Division Multiplexing,PDM)和偏振分集接收(Polarization Diversity Receiver,PDR)的CO-OFDM系统(MIMO CO-OFDM),可有效实抑制一阶PMD,并对系统信号传输机理及均衡算法以进行了数学分析。分析和仿真结果表明,在不需任何偏振控制器条件下,CO-OFDM系统可实现偏振光的不敏感接收,以10Gb/s的速率通过单模光纤传输800km,系统Q值保持在15dB以上。     

一种基于限幅的降低相干光OFDM系统非线性效应的方法

相干光正交频分复用系统(Coherent Optical-orthogonal frequency division multiplexing,简称CO-OFDM)可有效降低光纤色散效应,是近年来光传输领域研究热点之一.由于 OFDM 信号具有较高的峰均值功率比(Peak-to-average Power Ration,PAPR)和较窄的载波间隔,系统对非线性效应十分敏感,严重影响传输性能.文章介绍了一种基于信号限幅的CO-OFDM系统,通过载波选择和信号限幅,有效提高系统非线性容限,同时消除限幅噪声带来的影响.理论分析和仿真结果表明,在不需任何在线色散补偿条件下,基于限幅的CO-OFDM系统在单模光纤中传输960km,系统Q值较传统CO-OFDM系统有2dB提高,可完全消除限幅噪声影响.     

一种采用光学相位分集接收技术的相干光正交频分复用远端接入系统

提出了一种采用基于光学相位分集接收技术实现远程相干光正交频分复用(CO-OFDM)信号的远程光接入方案,并进行了理论研究和仿真验证。在本方案中,没有使用色散补偿光纤(DCF)或者色散补偿模块(DCM)补偿光纤信道色散导致的负面效应,原因是CO-OFDM信号能有效抵抗传输过程中色度色散(CD)和偏振模色散(PMD)引起的负面效应。仿真结果表明,10Gbit/s CO-OOFDM信号在标准单模光纤(SMF-28)传输320km后,采用相位估计技术得到的OFDM电信号,其时域波形的相位抖动幅度更小;与采用光载波自提取技术接收相位调制COOFDM的方案进行比较,测试误差向量幅度(EVM)的结果表明,本文方案可以获得更好的COOFDM信号接收性能,星座图中星座点收敛更加紧凑,接收的CO-OFDM信号质量更高。     

具有不同色散分布链路的高速CO-OFDM系统中非线性损伤的研究

由于相干光正交频分复用(CO-OFDM)系统很高的峰均功率比(PAPR)以及非常近的子载波间隔,使得链路色散导致的子载波走离对光纤非线性损伤的影响更加明显。研究了不同色散分布、不同残余色散情况下,无色散补偿光纤(DCF)和有色散补偿光纤的光纤链路时CO-OFDM系统的非线性损伤以及系统性能。针对单信道40 Gb/s CO-OFDM系统,无DCF链路比完全补偿DCF链路,Q因子高5.1 dB;对于DCF链路,当残余色散从0变为到1200ps/nm时,最大Q因子提高了4dB,非线性阈值提高了4 dBm,1200ps/nm时性能几乎和无色散补偿系统相同。     

光PM-DQPSK调制格式性能研究

对偏振复用-33%归零-差分正交相移键控(PM-33%RZ-DQPSK)和偏振复用-抑制载波归零-差分正交相移键控(PM-CSRZ-DQPSK)调制格式进行了传输性能仿真,在仿真过程中,分别考虑了光纤系统中的偏振模色散(PMD)、色散(CD)和非线性效应(SPM)三种限制因素。仿真结果表明偏振复用系统比非偏振复用系统更易受到PMD、CD和非线性效应的影响。整体来看,PM-CSRZ-DQPSK调制格式的传输性能比PM-33%RZ-DQPSK更为优秀。     

相干光OFDM在高速光传输中的应用

相干光正交频分复用系统(CO-OFDM,Coherent Optical Orthogonal Frequency Division Multiplexing)可有效抑制光纤色度色散和偏振模色散,有望成为解决未来高速光传输的主流方案。这里结合光传输理论及正交频分复用系统(OFDM,Orthogonal Frequency Division Multiplex)技术原理,对CO-OFDM系统方案实现及信道等效模型进行了分析,通过数字仿真验证系统光调制器偏置点选择及信号均衡算法。理论分析和仿真结果表明,CO-OFDM系统采用单抽头频域均衡,可有效抑制光纤色散效应。光调制器偏置点选择在零点,可实现系统对OFDM信号的最佳线性调制,与传统强度调制/直接检测(IM/DD)系统比较,CO-OFDM系统品质因子有10 dB提高。     

光纤OFDM系统中的色散补偿技术研究

为了减小光纤的色度色散对光纤正交频分复用（OFDM）系统性能的影响,提出了将无线通信中的信道估计器引入光纤OFDM系统进行信道估计的色散补偿方法。在理论上分析了光纤的色度色散对于传输OFDM信号的影响,并在实验中采用梳状导频的形式,在每个OFDM码元的特定的子载波上插入导频,在接收端通过基于最小平方（LS）原则的LS估计器进行信道估计,得到了OFDM光纤传输的信道幅度响应和相位响应,通过使用LS估计器,直接调制的光OFDM信号在单模光纤中传输200km,误比特率低于10-6 ,功率代价小于2dB。结果表明,高频子载波较低频子载波更容易受到色散的影响,在光纤OFDM系统中引入信道估计器进行信道估计能够有效补偿由色度色散带来的相位偏移和幅度衰减。     

对40 Gb/s OTDM系统中光纤光栅色散补偿器进行偏振模色散补偿的研究

改变光纤光栅紫外曝光系统 ,在相位掩模板后插入一个旋转装置 ,使得光纤在制作过程中可以进行某种旋转。通过这种方法制作的光纤光栅偏振模色散减小到平均差分群时延 (DGD)约为 0 2ps,而没加旋转制作的光纤光栅平均DGD约为 18 2 ps。采用两个这种低偏振模色散 (PMD)的光纤布拉格光栅 (FBG) ,成功地在 4 0Gb/s光时分复用 (OTDM)系统中补偿了约 2 0 4 0 ps的色散 ,该系统在经过 12 2km普通单模光纤传输后 ,未发现PMD的影响 ,传输功率代价小于 1 4dB。     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

Integrated circuits (ICs) intended for increasingly sophisticated automotive applications bring unique test demands. Advanced ICs for applications such as highly integrated automatic braking system (ABS) and airbag controllers combine high voltage digital channels, significant VI demands and precise timing capability. Along with continued missioncritical reliability concerns, the trend toward higher voltage operation and increased device integration requires specialized test capabilities able to extend across the wide operating ranges found in automotive applications. Among these capabilities, automotive test requirements increasingly dictate a need for a cost-effective versatile mixed-signal pin electronics with very high data rates reaching up to 50MHz with a voltage swing of-2 V to +28 V.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

Optical vibration and deviation measurement of rotating machine parts

It is of interest to get appropriate information about the dynamic behaviour of rotating machinery parts in service. This paper presents an approach of optical vibration and deviation measurement of such parts. Essential of this method is an image derotator combined with a high speed camera or a laser doppler vibrometer （LDV）.