智能家居ZigBee网络的构建与路由优化

ZigBee网络技术是一项新兴的低成本、低功耗的短距离无线通信技术,在智能家居中有广阔的应用前景。介绍了智能家居中ZigBee的通讯协议和网络地址分配方法,并针对传统的AODVjr路由算法在路由过程中RREQ分组过量洪泛问题和Cluster-Tree算法只按父子关系选择路由问题,提出了一种改进路由算法。改进算法将AODVjr和Cluster-Tree算法相结合,引入邻居表,适当控制RREQ转发方向,并考虑节点最小剩余能量。仿真结果表明,改进算法可以减少路由开销,延长节点的生存时间,均衡网络负荷。     

基于簇树AODVjr的混合动态成簇路由算法北大核心

针对ZigBee无线传感器网络在移动过程中严重丢包和能量受限问题,通过分析簇算法、簇树(ClusterTree)与AODVjr混合算法,设计了一种基于ClusterTree+AODVjr协议的混合动态成簇路由算法。该算法采用动态成簇机制,能够使节点移动后及时响应拓扑变化,快速重建网络连接,减少丢包现象,提高网络有效分组递交率;同时利用减少RREQ(路由请求分组)的洪泛广播来降低能耗。利用网络仿真器NS2进行了仿真实验,结果表明与原ClusterTree+AODVjr算法相比,该改进算法可平均降低14%的能耗,提高8%的平均有效分组递交率。     

一种基于动态概率转发的AODV路由协议

在Ad hoc网络(自组织网络)的路由建立过程中,由于AODV(Ad hoc按需距离矢量)路由采用洪泛方式转发RREQ(路由请求)消息会产生很多不必要的重传,很可能引发广播风暴而影响网络性能。文章提出了一种基于动态概率转发RREQ消息的改进方案,该方案根据邻居节点的个数选择不同的概率转发RREQ消息。仿真结果表明,在网络节点较多且网络比较稠密的情况下,改进方案能有效减少网络端到端时延,提高网络吞吐量和分组投递率。     

一种能量平衡的无线体域网络AODV多播路由发现协议

在动态网络拓扑中,AODV协议通过数据源节点S泛洪广播RREQ消息请求到任意目标节点D的路由,而在无线体域网络中,只有一个sink目标节点,除最短跳数路由上的节点外,其他参与RREQ接收和转发的节点浪费了能量。提出了一种能量平衡的无线体域网络AODV多播路由发现协议,通过在节点广播的hello消息中增加到sink的最小跳数hops、到sink的下一跳节点next和节点本身是否具备转发能力isforward 3 个参数,只选择能到达sink节点的邻居节点参与转发RREQ消息,变广播为多播,有效地降低了路由发现的能量开销,并通过能量平衡延长了WBAN的使用寿命。性能分析与模拟实验表明,该协议在RREQ数量、数据传输率和能量消耗等方面优于相似协议EAAODV。     

ZigBee路由算法的改进

网络层的路由协议是ZigBee协议规范的研究重点之一,因为网络节点中节点的能量资源、计算能力和带宽都非常有限,路由算法优化与否对整个网络的性能有着至关重要的作用。从控制RREQ分组以及能量均衡的角度出发,对AODVjr算法提出了改进。通过仿真实验,将改进的算法与原AODVjr算法进行性能参数的比较分析,实验结果验证了改进后的算法的有效性。     

基于灰色关联的ZigBee网络混合路由算法

ZigBee网络混合路由算法(ZigBee Routing,ZBR)中将源节点和目的节点之间的最小跳数作为唯一的路由度量因素.但随着节点能量消耗以及节点的频繁移动,ZBR算法的这一特性会造成网络间歇性连接,从而导致网络性能下降.提出一种选择最优分组转发路径的ZigBee网络混合路由算法(Grey Relational Algorithm based ZBR,GRA-ZBR).GRA-ZBR算法在目的节点选择路径时引入灰色关联算法,综合考虑节点剩余能量、链路质量、节点剩余队列长度以及路径长度等因素.仿真结果表明,GRA-ZBR算法可以有效提高网络分组投递率,降低平均端到端时延.     

基于节点特性的LR-WPAN网络能量优化路由算法

针对ZigBee网络混合路由算法的不足,考虑低速无线个域网(LR-WPAN)网络的能耗问题,提出了一种基于ZBR路由协议的改进算法(F-ZBR).本算法通过定义最小路由能量值和控制路由请求分组(RREQ)的传输方向、跳数以及在RREQ分组中加入能量标志位等措施,降低网络的整体能耗.仿真结果表明,F-ZBR算法的分组投递率、网络可用节点比率和网络剩余能量都较ZBR有明显提高,从而可以延缓ZigBee网络中大量数据传输造成的RN+节点能量过度损耗而导致的网络瘫痪等问题的发生,延长网络生命周期.     

基于灰色关联的ZigBee网络混合路由算法研究

ZigBee网络混合路由算法(ZigBee Routing,ZBR)中将源目的节点之间的最小跳数作为唯一的路由度量因素。但随着节点能量消耗以及节点的频繁移动,ZBR算法的这一特性会造成网络间歇性连接,从而导致网络性能下降。本文提出一种选择最优分组转发路径的ZigBee网络混合路由算法—GRA-ZBR算法。GRA-ZBR算法在目的节点选择路径时引入灰色关联算法,综合考虑节点剩余能量、链路质量、节点剩余队列长度、以及路径长度等因素。仿真结果表明：GRA-ZBR算法可以有效提高网络分组投递率,降低平均端到端时延。     

ZigBee路由协议算法的研究

通过对ZigBee中的Cluster-Tree算法以及对AODVjr中的路由发现进行研究,在Cluster-Tree邻居表的基础上提出捷径路由,从该节点周围的邻居节点中找出可以用少量跳数即可到达目的节点。此后通过路由代价函数,计算通过Cluster-Tree改进算法中找到节点路径的能量使用代价,选择可靠性较高的路径,从而可以延长网络生存周期和降低能耗。最后通过实例,验证了算法改进的可行性。     

基于限制广播域和节点剩余能量的按需路由算法研究

按需路由协议AODV的路由发现使用洪泛方式的扩散法,导致网络超负荷运行和拥塞,而且在选择转发路由时,总是选择最少跳数的路由,造成无线传感网络中节点能量不均,减少网络寿命.本文提出了AODV-DE算法,该算法引入广播域的概念,限制RREQ分组的转发范围,同时避免使用剩余能量低的节点转发数据分组,选择路由路径时选择总剩余能量最多的路径进行信息的传送.仿真结果表明,AODV-DE协议在路由开销、网络寿命和端到端的延迟这三个方面表现出了优势.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.