采用数字辅助直流失调消除技术适用于WCDMA/GSM接收机的双模模拟基带

A dual-mode analog baseband with digital-assisted DC-offset calibration (DCOC) for WCDMA/GSM receiver is presented. A digital-assisted DCOC is proposed to solve the DC-offset problem by removing the DC-offset component only. This method has no bandwidth sacrifice. After calibration the measured output residual offset voltage is within 5 mV at most gain settings and the IIP₂ is more than 60 dBm. The baseband is designed to be reconfigurable at bandwidths of 200 kHz and 2.1 MHz. Total baseband gain can be programmed from 6 to 54 dB. The chip is manufactured with 0.13 μm CMOS technology and consumes 10 mA from a 1.5 V supply in the GSM mode including an on-chip buffer while the core area occupies 1.2 mm².     

A dual-mode analog baseband with digital-assisted DC-offset calibration for WCDMA/GSM receivers

A dual-mode analog baseband with digital-assisted DC-offset calibration(DCOC) for WCDMA/GSM receiver is presented.A digital-assisted DCOC is proposed to solve the DC-offset problem by removing the DC-offset component only.This method has no bandwidth sacrifice.After calibration the measured output residual offset voltage is within 5 mV at most gain settings and the IIP2 is more than 60 dBm.The baseband is designed to be reconfigurable at bandwidths of 200 kHz and 2.1 MHz.Total baseband gain can be programmed from 6 to 54 dB.The chip is manufactured with 0.13μm CMOS technology and consumes 10 mA from a 1.5 V supply in the GSM mode including an on-chip buffer while the core area occupies 1.2 mm~2.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Nanomodulators Capable of Timely Scavenging ROS for Inflammation and Prognosis Control Following Photothermal Tumor Therapy

Despite the accuracy advantages of photothermal therapy (PTT), heat stress-initiated free radicals and damage-activated immune cells form a malignant positive feedback cycle following light irradiation. Herein, a 2D allomelanin nanomodulator with perpendicularly oriented oligomer planes is prepared by the guidance of DNA to achieve timely scavenging of reactive oxygen species (ROS) for inflammation and prognosis control following PTT. A large exposure degree of phenol groups and the effective transfer of delocalized electrons result in ultra-fast redox reactions that can be boosted by a self-amplifying process through structure disintegration. Compared with conventional photothermal agents, the nanodisks reduce the accumulation of ROS during PTT by 25-fold, downregulate the proinflammatory factors, and adjust inflammation levels to baseline. Thereby, successful modulation of M2-type macrophages in paratumor tissues significantly prevents burn wound progression and accelerates tissue repair, while well-controlled neutrophil extracellular traps and largely recruited CD4⁺/CD8⁺ T cells (1.6–3.2-fold) in the ablation site suppress the relapse of distant tumors. The study provides a useful inspiration on rationally modulating redox active nanostructures to address prognosis issues following PTT.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

The advantages of radical distribution control and independent dual frequency on etch/ash

The transition to 65 nm beyond and 300 mm wafers posed many challenges on etch depth and critical dimension (CD) uniformity within wafer. In this paper, we introduce a radical distribution control (RDC) system for an excellent uniformity control.Etch depth and CD uniformity within wafer are well controlled by adding RDC function to SCCMTM. For increasing productivity, an all-in-one process, that is, etch/ash at the same chamber continuously is proposed here. By utilizing the advantage of independent dual frequency, a bias-controlled two-step ash "hybrid ash" is combined in the all-in-one process. Hybrid ash uses bias control and low pressure to minimize liner loss and the damage of low-k materials, which is targeting 65nm and beyond.