Transient liquid phase sintering of high-purity mullite for high-temperature structural ceramics

High-purity mullite ceramics, promising engineering ceramics for high-temperature applications, were fabricated using transient liquid phase sintering to improve their high-temperature mechanical properties. Small amounts of ultrafine alumina or silica powders were uniformly mixed with the mullite precursor depending on the silica-alumina ratio of the resulting ceramics to allow for the formation of a transient liquid phase during sintering, thus, enhancing densification at the early stage of sintering and mullite formation by the reaction between additional alumina and the residual glassy phase (mullitization) at the final stage of sintering. The addition of alumina powder to the silica-rich mullite precursor resulted in a reaction between the glassy silica and alumina phases during sintering, thereby forming a mullite phase without inhibiting densification. The addition of fine silica powder to the mullite single-phase precursor led to densification with an abnormal grain growth of mullite, whereas some of the added silica remained as a glassy phase after sintering. The resulting mullite ceramics prepared using different powder compositions showed different sintering behaviors, depending on the amount of alumina added. Upon selecting an optimum process and the amount of alumina to be added, the pure mullite ceramics obtained via transient liquid phase sintering exhibited high density (approximately 99%) and excellent high-temperature flexural strength (approximately 320 MPa) at 1500 °C in air. These results clearly demonstrate that pure mullite ceramics fabricated via transient liquid phase sintering with compositions close to those of stoichiometric mullite could be a promising process for the fabrication of high-temperature structural ceramics used in an ambient atmosphere. The transient liquid phase sintering process proposed in this study could be a powerful processing tool that allows for the preparation of superior high-temperature structural ceramics used in the ambient processing atmosphere.     

Pregnancy by Assisted Reproductive Technology Is Associated with Shorter Telomere Length in Neonates

Telomere length (TL) influences the development of lifestyle-related diseases, and neonatal TL may influence their prevalence. Various factors have been reported to affect neonatal TL. Although the fetus is exposed to multiple conditions in utero, the main factors affecting the shortening of neonatal TL are still not known. In this study, we sought to identify factors that influence fetal TL. A total of 578 mother-newborn pairs were included for TL analysis. TL was measured in genomic DNA extracted from cord blood samples using quantitative PCR. The clinical factors examined at enrollment included the following intrauterine environmental factors: maternal age, assisted reproductive technology (ART) used, body mass index (BMI), gestational diabetes mellitus (GDM), maternal stress, smoking, alcohol consumption, preterm delivery, small-for-gestational-age, neonatal sex, and placental weight. Univariate and multivariate regression analyses were used to verify the relationship between neonatal TL and these clinical factors. The median neonatal TL to single-copy gene ratio was 1.0. Pregnancy with ART was among the 11 factors associated with shorter neonatal TL. From multiple regression analysis, we determined that neonatal TL was significantly shorter for pregnancies in the ART group than in the other groups. We conclude that pregnancy with ART is associated with shorter neonatal TL.     

Structural Characterization of Neutral Glycosphingolipids from 3T3‐L1 Adipocytes

In recent years, obesity has been considered a pathological stage of early lifestyle‐related diseases, and adipose tissue and adipocyte research has been active. Glycosphingolipids are involved in the pathogenesis of type 2 diabetes induced by insulin resistance, but the details of the glycosphingolipid molecular species composition of adipocytes have yet to be elucidated. We used 3T3‐L1 adipocytes and the 1,2‐dichloroethane‐wash method to remove triacylglycerols, which are abundant in adipocytes, and analyzed the structures of glycosphingolipids, particularly neutral glycosphingolipids, using liquid chromatography–mass spectrometry.     

Effect of pitting corrosion on strength of web plates subjected to patch loading

Pitting corrosion is typical corrosion observed on coated hold frames in way of cargo holds of bulk carriers, which exclusively carry coal and iron ore. Extensive survey on the effect of pitting corrosion on structural strength under a wide variety of loading conditions is necessary to clarify the relationship between pitting intensity and residual strength in detail. In the present study, a series of tests has been conducted on structural models which consist of web, shell and face plates to investigate the effect of pitting corrosion on strength of web plates subjected to patch loading. In these tests, artificial pitting was made on the web plates and two equal concentrated loads have been applied vertically at the one third points of simply supported models. It was found that web crippling behavior is strongly affected by the pit distribution on the web plates. According to the FE-analyses following the experiment, ultimate strength of the web plates with pitting under patch loading is a little smaller than or almost the same as that of the web plates with uniform corrosion in terms of average thickness loss.     

A new approach for simulating aerodynamic vibrations of structures in a wind tunnel—development of an experimental system by means of hybrid vibration technique

The present paper describes a newly proposed technique for simulating aerodynamic vibration of structures, which is referred to as the hybrid vibration technique or HVT. This technique is a combination of step-by-step computer calculation and measurement of the aerodynamic force acting on a model structure in a wind tunnel test. Even though the HVT can be applied effectively, problems still exist with respect to obtaining accurate simulations. These problems include response delay in controlling the model behavior and the inertia force component present in the measured aerodynamic force. Techniques for compensating for response delay and for eliminating inertia force from measured aerodynamic force are applied to a developed system based on HVT simulations of aerodynamic vibration of elastic structures and structures exhibiting elasto-plastic behavior are performed by means of the newly developed system. The effectiveness of the techniques for compensating for the response delay and eliminating the inertia force can be confirmed from the results of the simulations. In addition, the possibility and applicability of HVT is indicated.     

Cooperative Control by System Voltage Control Equipments in Consideration of Reducing Capacity of STATCOM

In recent years, the number of renewable energy sources (RESs) such as photovoltaic generation systems and wind power generation systems connected to the grid has been increasing as a way of reducing negative effects on the environment. The outputs of these RESs vary rapidly because of the influence of the weather and the conditions of the location. Therefore, there are concerns that the point voltages in a distribution system may vary drastically and that the voltages may deviate from the appropriate voltage range as a result of the influence of the RES connected to the distribution system or to the diversification of loads. Furthermore, there are concerns about adverse effects on electric power quality, such as voltage imbalances and harmonics. In this paper, we propose a cooperative voltage control method for a distribution system using system voltage control equipment in order to reduce the capacity of the static synchronous compensator. Numerical calculations were performed in order to verify the validity of the proposed method.