Inulin-based emulsion-filled gel as a fat replacer in prebiotic- and PUFA-enriched dry fermented sausages

In order to produce fermented sausages with prebiotic fibre and improved fatty acid composition, 16% of pork back fat was replaced with inulin gelled suspension (I) and inulin linseed oil gelled emulsion (IO). Physico-chemical analysis, fatty acid profiles, lipid oxidation, microbiological, textural, colour and sensory analysis were carried out. The fat content was lower in I (31.38%) and IO (35.36%) modified sausages compared to control (44.37%) (P < 0.05). IO sausages had lower SFA and MUFA and higher PUFA content with an improved n-6/n-3 ratio (2.23) (P < 0.05) and α-linolenic acid increment (5.74 g per 100 g). Reformulation led to decrease in springiness, chewiness and hardness and increase in adhesiveness of the sausages. Modified sausages had lower L* and higher a* values, while b* values of I sausages did not differ compared to control sausages. Modified sausages were acceptable regarding all sensory attributes. Lipid oxidation parameters showed higher susceptibility to oxidation and lipolysis in IO sausages.     

Nanocrystalline Zn2SnO4/SnO2: Crystal structure and humidity influence on complex impedance

Journal of Electroceramics - Nanocrystalline Zn2SnO4/SnO2 powder was obtained by a solid state reaction of ZnO and SnO2 nanopowders mixed in the molar ratio 1:1. The phase composition of the...     

Variable neighbourhood simulated annealing algorithm for capacitated vehicle routing problems

This article presents the variable neighbourhood simulated annealing (VNSA) algorithm, a variant of the variable neighbourhood search (VNS) combined with simulated annealing (SA), for efficiently solving capacitated vehicle routing problems (CVRPs). In the new algorithm, the deterministic ‘Move or not’ criterion of the original VNS algorithm regarding the incumbent replacement is replaced by an SA probability, and the neighbourhood shifting of the original VNS (from near to far by k← k+1) is replaced by a neighbourhood shaking procedure following a specified rule. The geographical neighbourhood structure is introduced in constructing the neighbourhood structures for the CVRP of the string model. The proposed algorithm is tested against 39 well-known benchmark CVRP instances of different scales (small/middle, large, very large). The results show that the VNSA algorithm outperforms most existing algorithms in terms of computational effectiveness and efficiency, showing good performance in solving large and very large CVRPs.     

Substituted imino and amino derivatives of 4-hydroxycoumarins as novel antioxidant,antibacterial and antifungal agents: Synthesis and in vitro assessments

A series of imino and amino derivatives of 4-hydroxycoumarins were synthesised and evaluated for antioxidant potential, through different in vitro models such as (DPPH) free radical-scavenging activity, linoleic acid emulsion model system, reducing power assay and phosphomolybdenum method. Also, antimicrobial activity of obtained coumarins was evaluated against 13 bacteria and eight fungi. All prepared compounds possessed good antioxidant activity and among them a p-nitrophenol derivative with IC₅₀ at 25.9 μM possessed radical-scavenging activity which was comparable to BHT. Observed data for antibacterial activity indicated strong activity of all tested amino derivatives, while imines showed better antifungal properties.     

COMPARISON AND VALIDATION OF OHM AND SCEM MEASUREMENTS FOR A FULL-SCALE COAL-FIRED POWER PLANT

Mercury emission measurements were performed at a 250 MW coal-fired power plant using the Ontario Hydro method (OHM) and semi-continuous emission monitors (SCEM). Flue gas sampling was performed at the inlet of the air preheater and at the outlet of the electrostatic precipitator. The results indicated that there is some agreement between the OHM and SCEM measurements on the total mercury species. However, the SCEM results were not always in good agreement with the OHM measurements on the elemental mercury species. These discrepancies in elemental mercury concentrations are probably the result of the differences in the location of the SCEM and OHM probes, the temperature difference between the SCEM sampling probe and the flue gas, and the nonuniformities in mercury concentration over the flue gas duct cross section. The other factor that contributed to the deviation between the SCEM and OHM measurement results is the sampling method: the SCEM measurements were performed at a single point while the OHM probe was traversed over multiple points over the duct cross section and the results were averaged. The effect of the SCEM sampling probe temperature was investigated by designing a sampling probe that could be heated to the sampled flue gas temperatures. This resulted in improvements in the accuracy of the elemental mercury measurements by the SCEM system.     

Semantic Mediation for Standard-Based B2B Interoperability

The authors discuss a semantic-mediation architecture to advance traditional approaches for standards-based business-to-business (B2B) interoperability. The architecture is supported by the Athena Knowledge Representation and Semantics Mediation tool suite. Initial experimentations with the architecture and the toolset offer discussions of key architectural and functional aspects and suggest directions for future tools enhancements.     

Analysis of the strain and hardness in self-cured and light-cured self-adhesive resin based cement

The study showed an application of the 3?D Digital Image Correlation Method (3?D-DIC) for detection of von Mises strain in samples of the self-etch, self-adhesive resin based cement (RBC). The aim was to determine and compare strain in the self-cured and light-cured Maxcem Elite, furthermore to investigate the hardness of these two cement-types. The experiment was carried out using two groups of Maxcem Elite (Kerr, Orange, CA, USA) samples; each tested group includes five (ø5?×?2?mm sized) samples, for both self-curing and light-curing mode. All samples were prepared by filling teflon ring-type molds. In addition, Vickers micro-hardness was measured for all samples. Maxcem Elite showed similar maximum strain values from 10% to 12% for both groups. Besides the maximum strain value, the 3?D-DIC method also enabled monitoring the change of strain field even after the recommended polymerization time. This method has shown that the polymerization shrinkage continues even after 10?min which disagreed with manufacturer’s suggestion. Group II showed maximum strain values of 12% in the peripheral zone after 10?min, in the last Stage (Stage 60). Statistically significant difference was not found in the overall strain between self- and light-cured Maxcem Elite neither peripherally (p?=?0.118) nor centrally (p?=?0.879). However, statistical significance was found in strain regarding central and peripheral zone in both, self-cured (p?=?0.020) and light-cured (p?=?0.002) Maxcem Elite. The mean von Mises strain values in the periphery of the samples (Section 0) were significantly higher compared to strain values in the center of the samples (for Section 1 and 2). The last stage (Stage 60) of the light-cured Maxcem Elite polymerization showed significantly higher values of von Mises strain compared to initial stage (Stage 0). Higher values of micro-hardness were noticed on the surfaces directly exposed to LED lamp after performing measurements of micro-hardness on light-cured samples.     

Simple and efficient integration of rigid rotations suitable for constraint solvers

Simple and efficient way of integrating rigid rotations is presented. The algorithm is stable, second‐order accurate, and in its explicit version involves evaluation of only two exponential maps per time step. The semi‐explicit version of the proposed scheme improves upon the long‐term stability, while it retains the explicitness in the force evaluation. The algebraic structure of both schemes makes them suitable forthe analysis of constrained multi‐body systems. The explicit algorithm is specifically aimed at the analysis involving small incremental rotations, where its modest computational cost becomes the major advantage. The semi‐explicit scheme naturally broadens the scope of possible applications. Copyright © 2009 John Wiley & Sons, Ltd.