Structure-conductivity relationship of PrBaMnMoO6-δ through in-situ measurements: A neutron diffraction study

The structural and electrochemical properties of the double perovskite-type oxide, PrBaMnMoO_6-δ, was investigated using neutron diffraction with in-situ conductivity measurement under a dry Argon atmosphere from 25 °C to 700 °C. A Rietveld refinement of the neutron diffraction data confirmed monoclinic symmetry in the P2₁/n space group. Rietveld refinement also confirms the unit cell parameters of a = 5.6567 (1) Å, b = 5.6065 (2) Å, c = 7.9344 (1) Å and β = 84.43° with reliable atomic positions and refinement factors (R-factors). Neutron diffraction data refinement shows two minor phases (<5%), an orthorhombic AB₂O₅ type phase of PrMn₂O₅ in the Pbam (No. 32) space group with unit cell parameters, a = 7.9672 (1) Å, b = 8.9043 (2) Å and c = 5.8540 (1) Å and a scheelite phase of BaMoO₄ in the tetragonal I4₁/a (88) space group with the unit cell parameters, a = b = 5.9522 (1) Å, and c = 12.3211 (2) Å. Morphological images revealed a porous and intertwined microstructure. In-situ conductivity measurement shows that the total conductivity of this material was 130.84 Scm^?1 at 700 °C.     

Salt-assisted solution combustion synthesis of NiFe2O4: Effect of salt type

The effects of three types of salt including NaF, KCl, and NaCl on the properties of NiFe₂O₄ nanoparticles using salt-assisted solution combustion synthesis (SSCS) have been investigated. The synthesized powders were evaluated by SEM, TEM, FTIR, XRD, and VSM analysis. Also, the specific surface area (SSA), as well as size distribution and volume of the porosities of NiFe₂O₄ powders were determined by the BET apparatus. The visual observations showed that the intensity and time of combustion synthesis of nanoparticles have been severely influenced by the type of salt. The highest crystallinity was observed in the synthesized powder using NaCl. The SSA has also been correlated completely to the type of salt. The quantities of SSA was achieved about 91.62, 64.88, and 47.22 m²g^-1 for the powders synthesized by KCl, NaCl, and NaF respectively. Although the magnetic hysteresis loops showed the soft ferromagnetic behavior of the NiFe₂O₄ nanoparticles in all conditions, KCl salt could produce the particles with the least coercivity and remanent magnetization. Based on the present study, the salt type is a key parameter in the SSCS process for the preparation of spinel ferrites. Thermodynamic evaluation also showed that the melting point and heat capacity are important parameters for the proper selection of the salt.     

Effect of Co addition on microstructural and mechanical properties of WC–B4C–SiC composites

In this study, the effect of Co addition on microstructural and mechanical properties of WC-B₄C–SiC composites sintered by spark plasma sintering (SPS) method was investigated. For this purpose, three batches of WC-B₄C–SiC with different contents of Co (10 vol%, 15 vol%, and 20 Vol %) were sintered at 1400 °C. The results of X-ray diffraction (XRD) analysis of the samples indicated the formation of W₂B₅, W₃CoB₃ as well as the remained C phases and unreacted SiC phase. It was observed that by increasing the Co content, the amount of W₂B₅ phase reduces and W₃CoB₃ and C contents increase. Therefore, W₂B₅ peaks were not detected in the sample containing 20vol% Co. Relative density values above 97% were obtained for all the composites. However, a decrease was observed in relative density by increasing the Co content in the composites. The highest flexural strength (510 ± 42 MPa), fracture toughness (10.34 ± 0.82 MPa m^1/2), and hardness (20.63 ± 0.75 GPa) were also obtained for the sample containing 10vol% Co compared to the other samples. In addition, Transgranular fracture of SiC as well as pulling out of W₃CoB₃ and W₂B₅ particles were observed in the fracture surface micrographs of the samples. The presence of micro-cracks in the SiC grains, fracture of W₃CoB₃ grains, and crack deflection was reported as dominant toughening mechanisms.     

Inter-cell interference in multi-tier heterogeneous cellular networks: modeling and constraints

Telecommunication Systems - Interference is the main source of capacity limitation in wireless networks. In some medium access technologies in cellular networks, such as OFDMA, the allocation of...     

Combining a new baseboard radiator with a fan coil system for improving heating performance and reduce energy consumption

In the present work, the heating performance of a new system combined with a new modified baseboard radiator and fan coil is investigated. Using longitudinal fins with special geometry and also forced airflow at the end of the system causes that at the lower inlet water temperature compared with the conventional models, higher heat output rate be obtained. The heat output rate of the new modified system is obtained by experimental metrology based on the European Standard No. EN-442. Temperature and velocity distribution in the room space is done by simulation of the modified system in the Flovent software. Computational fluid dynamics (CFD) results are validated against experimental results and there is a good agreement between them. Also, the energy consumption of the system during the winter season is calculated in TRANSYS software. Experimental results show that the heat output rate of a new modified heating system with inlet water temperature in the range of 45–55°C is on average 4.17 times higher compared with the conventional model. CFD simulation also showed that the combined system provides good thermal comfort conditions. Energy consumption of the new system reduced about 13% compared with conventional models.     

A circuit-level methodology for leakage power reduction of high-efficient compressors in 22-nm CMOS technology

Analog Integrated Circuits and Signal Processing - A new circuit-level methodology called input controlled leakage restrainer transistor (ICLRT) compatible with single threshold CMOS technology is...     

An Efficient Digital Confidentiality Scheme Based on Commutative Chaotic Polynomial

Multimedia Tools and Applications - One of the most critical aspects of this technologically progressive era is the propagation of information through an unsecured communication channel. The...     

A Statistical Model for Early Detection of DDoS Attacks on Random Targets in SDN

Wireless Personal Communications - Software Defined Networks (SDNs) have accelerated and simplified the management, configuration and error detection in today’s networking systems. However,...     

Review: the latest advances in biomedical applications of chitosan hydrogel as a powerful natural structure with eye-catching biological properties

Journal of Materials Science - Chitosan is one of the natural cationic polymers with unique properties such as non-toxicity, biodegradability, biocompatibility, environmentally friendly that has...     

Synthesis,characterization and magnetic properties of polythiophene/SrFe12-x(ZrZn)0.5xO19 nanocomposite as a microwave absorber

Ferrites are an important group of magnetic materials which are used as absorbers. The incorporation of ferrite and conducting polymer achieves great enhancement in microwave absorption properties. The nanocomposites of hexagonal ferrites embedded by conducting polymers such as polypyrrole, polyaniline and polythiophene (PTH) have been paid much attention. In the present study, strontium hexagonal ferrite doped by Zr and Zn with the final formula of SrFe_12-x(ZrZn)_0.5xO19 considering x = 0.9 and embedded by PTH was produced to achieve a nanocomposite with the highest microwave absorbing ability. In this study, after synthesis of SrFe₁₂O₁₉(ZrZn)_0.5xO19 and PTH, the nanocomposite was prepared by in situ polymerization. Wrapping the ferrite particles and PTH chains could form nanocomposite properly, and therefore acceptable interactions were observable between SrFe_12-x(ZrZn)_0.5xO19ferrite particles and PTH polymer chains in the composites. Assessing the X-ray diffraction (XRD) patterns of SrFe_12-x(ZrZn)_0.5xO19, PTH, and PTH/SrFe_12-x(ZrZn)_0.5xO19 nanocomposite indicated that the PTH characteristic peak shifts slightly and its peak intensity reduces, which may be attribute to the coating of PTH polymer chains onto SrFe_12-x(ZrZn)_0.5xO19 particles. We revealed also lower magnetic properties in the obtained nanocomposite. The morphological assessment also suggested that PTH could effectively coat the SrFe_12-x(ZrZn)_0.5xO19 particles. The synergistic effect of SrFe_12-x(ZrZn)_0.5xO19 particle plus PTH leads to microwave absorption percentage higher than 95% by PTH/SrFe_12-x(ZrZn)_0.5xO19 nanocomposite. Overall, nanocomposite creating by coupling interaction between SrFe_12-x(ZrZn)_0.5xO19 particles (x = 0.9) and PTH can effectively lead to achieve the highest rate of absorption of electromagnetic waves.