Effect of Pre-cold Rolling-Induced Twins and Subsequent Precipitated x-Phase on Mechanical Properties in a β-Type Ti–Mo Alloy

This paper reported an effectiveness of pre-cold rolling-induced{332}\113[twins combined with subsequent isothermal x-phase formation for enhancement of uniform elongation in a b-type Ti–15Mo alloy with high yield strength level.Mechanical{332}\113[twins were induced by cold rolling with an thickness reduction of 5%,which had little effect on x-phase precipitation after aging at 573 K for 3.6 ks.Twinning after the cold rolling was further activated during tensile deformation,even with the presence of isothermal x-phase.This combination of twins and x-phase enhanced uniform elongation from 0 to 9%at yield strength level of 890 MPa.The high yield strength was mainly dominated by dislocation slip due to the isothermal x-phase formation,and early onset of plastic instability after yielding was hindered due to the pre-cold rolling-induced twins.Dynamic microstructural refinement was induced by further twinning activation during deformation,which resulted in high work hardening rate corresponding enhancement of uniform elongation.     

Fabrication of 0.24Pb(In1/2Nb1/2)O3-0.42Pb(Mg1/3Nb2/3)O3-0.34PbTiO3 transparent ceramics by conventional sintering technique

0.24Pb(In_1/2Nb_1/2)O₃-0.42Pb(Mg_1/3Nb_2/3)O₃-0.34PbTiO₃ transparent ceramics were fabricated by a conventional sintering technique. Through optimization of sintering conditions of calcination and sintering temperatures and time, the obtained ceramics showed high optical transmittance of 53% and 71% at light wavelengths of 1300 and 2000 nm, respectively. The ceramics showed a rhombohedral to tetragonal phase transition at ~120°C and a tetragonal to cubic phase transition at 222°C. These transition temperatures were higher than those of 0.67Pb(Mg_1/3Nb_2/3)-0.33PbTiO₃ ceramics. In addition, the ceramics had a ferroelectric hysteresis loop, a large piezoelectric constant d₃₃ of 407 pC/N, and a planar electromechanical coupling factor k_p of 52%. These results suggest that the transparent ceramics may be used as a temperature-stable, linear electro-optic material.     

Aerobic Exercise Ameliorates Cancer Cachexia-Induced Muscle Wasting through Adiponectin Signaling

Cachexia is a multifactorial syndrome characterized by muscle loss that cannot be reversed by conventional nutritional support. To uncover the molecular basis underlying the onset of cancer cachectic muscle wasting and establish an effective intervention against muscle loss, we used a cancer cachectic mouse model and examined the effects of aerobic exercise. Aerobic exercise successfully suppressed muscle atrophy and activated adiponectin signaling. Next, a cellular model for cancer cachectic muscle atrophy using C2C12 myotubes was prepared by treating myotubes with a conditioned medium from a culture of colon-26 cancer cells. Treatment of the atrophic myotubes with recombinant adiponectin was protective against the thinning of cells through the increased production of p-mTOR and suppression of LC3-II. Altogether, these findings suggest that the activation of adiponectin signaling could be part of the molecular mechanisms by which aerobic exercise ameliorates cancer cachexia-induced muscle wasting.     

Silver(I)-Ion-Mediated Cytosine-Containing Base Pairs: Metal Ion Specificity for Duplex Stabilization and Susceptibility toward DNA Polymerases

Spectroscopic characterization of Ag^I-ion-mediated C-Ag^I-A and C-Ag^I-T base pairs found in primer extension reactions catalyzed by DNA polymerases was conducted. UV melting experiments revealed that C-A and C-T mismatched base pairs in oligodeoxynucleotide duplexes are specifically stabilized by Ag^I ions in 1:1 stoichiometry in the same manner as a C-C mismatched base pair. Although the stability of the mismatched base pairs in the absence of Ag^I ions is in the order C-A≈C-T>C-C, the stabilizing effect of Ag^I ions follows the order C-C>C-A≈C-T. However, the comparative susceptibility of dNTPs to Ag^I-mediated enzymatic incorporation into the site opposite templating C is dATP>dTTP≫dCTP, as reported. The net charge, as well as the size and/or shape complementarity of the metal-mediated base pairs, or the stabilities of mismatched base pairs in the absence of metal ions, would be more important than the stability of the metallo-base pairs in the replicating reaction catalyzed by DNA polymerases.     

Engineering of Lipid Nanoparticles by the Multifunctionalization of the Surface with Amino Acid Derivatives for the Neutralization of a Target Toxic Peptide

Protein affinity reagents (e.g., antibodies) are often used for basic research, diagnostics, separations, and disease therapy. Although a lot of “synthetic” protein affinity reagents have been developed as a cost-effective alternative to antibodies, their low biocompatibility is a considerable problem for clinical application. Lipid nanoparticles (LNP) represent a highly biocompatible drug delivery agent. However, little has been reported that LNP itself works as a protein affinity reagent in living animals. Here, LNP is engineered for binding to and neutralizing a target toxic peptide in living animals by multifunctionalization with amino acid derivatives. Multifunctionalized LNP (MF-LNP) is prepared using amino acid derivative-conjugated lipids. Optimized MF-LNP exhibits nanomolar affinity to the target toxic peptide and inhibits toxic peptide-dependent hemolysis and cytotoxicity. In addition, MF-LNP captures and neutralizes the toxic peptide after intravenous injection in the bloodstream; in addition, MF-LNP does not release the toxic peptide in the accumulated organ. These results reveal the potential of using LNP as a highly biocompatible protein affinity reagent such as an antidote.     

Mass transfer in polycrystalline ytterbium monosilicate under oxygen potential gradients at high temperatures

Mass transfer in polycrystalline Yb₂SiO₅ wafers with precise composition control was evaluated and analyzed by oxygen permeation experiments at high temperatures using an oxygen tracer. Oxygen permeation proceeded due to mutual grain boundary diffusion of oxide ions and Yb ions without synergistic effects such as acceleration or suppression. The oxygen shielding properties of Yb₂SiO₅ were compared with those of the other line compounds such as Yb₂Si₂O₇ and Al₂O₃ based on the determined mass transfer parameters. It was found that the more preferentially an oxide ion diffuses in the grain boundary compared to the interior of the grain, the greater the effect of suppressing the movement of the oxide ion by applying an oxygen potential gradient becomes.     

Cold-start performance of an ammonia-fueled spark ignition engine with an on-board fuel reformer

This work demonstrated the first-ever cold-start operation of an ammonia (NH₃)-fueled four-cylinder spark ignition engine with an on-board fuel reformer, applying autothermal reforming. In this system, an electrically heated NH₃-air mixture was provided to a reforming catalyst and approximately 3 s was found to elapse between the start of engine rotation and the onset of combustion. Stable fast idle operation in conjunction with a cold start was realized with a H₂-to-NH₃ molar ratio of 2:1. Nearly zero NH₃ emissions were achieved during cold start and fast idle until the engine warmed up, by adsorbing unburned NH₃ passing through a three-way catalyst before the catalyst was sufficiently warmed up. The NH₃ adsorption capacity of this system could be regenerated during the engine warm-up when the engine was running under lean conditions.     

Fabrication and piezoelectric properties of BaTiO3/BaTiO3-Bi(Mg1/2Ti1/2)O3-BiFeO3 composites

We fabricated xBaTiO₃ (BT)/(1-x)[BaTiO₃-Bi(Mg_1/2Ti_1/2)O₃-BiFeO₃] (BT-BMT-BF)?+?0.1?wt%MnCO₃ composites by spark plasma sintering and investigated the effect of BT content x, BT powder size, and BT-BMT-BF composition on piezoelectric properties. For xBT/(1-x)(0.3BT-0.1BMT-0.6BF) +?0.1?wt%MnCO₃ (x?=?0–0.75) composites with a 0.5-µm BT powder, the dielectric constant was increased with x, and the relative density was decreased at x?=?0.67 and 0.75, creating optimum BT content of x?=?0.50 with a piezoelectric constant d₃₃ of 107?pC/N. When a larger 1.5-µm BT powder was utilized for the composite with x?=?0.50, the d₃₃ value increased to 150?pC/N due to the grain size effect of the BT grains. To compensate for a compositional change from the optimum 0.3BT-0.1BMT-0.6BF due to partial diffusion between the BT and 0.3BT-0.1BMT-0.6BF grains, a 0.5BT/0.5(0.275BT-0.1BMT-0.625BF)?+?0.1?wt%MnCO₃ composite with the 1.5-µm BT powder was fabricated. We obtained an increased d₃₃ value of 166?pC/N. These results provided a useful composite design to enhance the piezoelectric properties.     

Determination of atomistic deformation of tricalcium silicate paste with high-volume fly ash

We examined the effect of incorporating high-volume fly ash on the atomic arrangement and interatomic deformation behavior of calcium silicate hydrates in tricalcium silicate paste upon exposure to external forces. The interatomic structural changes and strains under compressive load were assessed using synchrotron in situ high-energy X-ray scattering-based atomic pair distribution function analysis. Three different types of strains, which were (a) macroscopic strains from gauges on the surfaces of specimen, (b) strains in a reciprocal space (Bragg peak shift), and (c) strains in real space (PDF peak shift), were compared to each other. All monitored and calculated strains for tricalcium silicate-fly ash (50 wt% fly ash) paste were compared with the counterparts of the pure tricalcium silicate paste. Pair distribution function analysis in the range of r < 10 Å indicated that the atomic arrangement of tricalcium silicate-fly ash was similar to that of synthetic calcium silicate hydrates followed by that of pure tricalcium silicate paste. Moreover, the pair distribution function refinement results revealed that the calcium silicate hydrate structure in tricalcium silicate-fly ash paste was similar to tobermorite 11 Å, unlike that in pure tricalcium silicate paste. The interatomic strain of tricalcium silicate-fly ash in the real space (r < 20 Å) was smaller than that of tricalcium silicate under compression, which suggested that the incompressibility of calcium silicate hydrates at atomistic scale was enhanced by the incorporation of fly ash into it. This was likely to be caused by the increased silicate polymerization of calcium silicate hydrates, which was attributed to the increase in the amount of silicate in their structure via the addition of fly ash.