Modelling landslides in unsaturated slopes subjected to rainfall infiltration using material point method

This paper presents a dynamic fully coupled formulation for saturated and unsaturated soils that undergo large deformations based on material point method. Governing equations are applied to porous material while considering it as a continuum in which the pores of the solid skeleton are filled with water and air. The accuracy of the developed method is tested with available experimental and numerical results. The developed method has been applied to investigate the failure and post‐failure behaviour of rapid landslides in unsaturated slopes subjected to rainfall infiltration using two different bedrock geometries that lie below the top soil. The models show different failure and post‐failure mechanisms depending on the bedrock geometry and highlight the negative effects of continuous rain infiltrations. Copyright © 2016 John Wiley & Sons, Ltd.     

A constitutive model for mechanical and chemo‐mechanical compaction in sedimentary basins and finite element analysis

Compaction and associated fluid flow are fundamental processes in sedimentary basin deformation. Purely mechanical compaction originates mainly from pore fluid expulsion and rearrangement of solid particles during burial, while chemo‐mechanical compaction results from Intergranular Pressure‐Solution (IPS) and represents a major mechanism of deformation in sedimentary basins during diagenesis. The aim of the present contribution is to provide a comprehensive 3D framework for constitutive and numerical modeling of purely mechanical and chemo‐mechanical compaction in sedimentary basins. Extending the concepts that have been previously proposed for the modeling of purely mechanical compaction in finite poroplasticity, deformation by IPS is addressed herein by means of additional viscoplastic terms in the state equations of the porous material. The finite element model integrates the poroplastic and poroviscoplastic components of deformation at large strains. The corresponding implementation allows for numerical simulation of sediments accretion/erosion periods by progressive activation/deactivation of the gravity forces within a fictitious closed material system. Validation of the numerical approach is assessed by means of comparison with closed‐form solutions derived in the context of a simplified compaction model. The last part of the paper presents the results of numerical basin simulation performed in one dimensional setting, demonstrating the ability of the modeling to capture the main features in elastoplastic and viscoplastic compaction. Copyright © 2016 John Wiley & Sons, Ltd.     

长江漫滩区深大异形基坑施工对紧邻特大型桥梁影响及变形控制研究

随着地下空间资源的开发利用,越来越多深基坑呈现出开挖深、规模大、形状不规则等特点,其支护结构设计复杂,施工难度大,具有明显的空间效应。本文以南京地铁某基坑工程为例,分析基坑施工对邻近桥梁的影响。其场区位于长江下游漫滩相二元结构地层分布地段,上部软土层厚度大,下部承压含水层地下水位高、水量丰富,地质条件复杂,该基坑为典型的深大异形基坑,距离某大桥的双曲拱引桥仅为7. 2 m,由于之前桥梁已遭受其他地下工程施工产生的较大变形,所以后续工程对其影响变形控制要求极高。为此,该车站基坑支护结构设计基于地下空间实际功能采用设置分隔墙分区开挖及MJS超深工法墙综合变形控制方案。本文通过有限元数值模拟计算,开展复杂环境下基坑开挖引起的围护结构及桥梁桩基的变形预测分析,计算结果显示,该深大狭长异形基坑开挖对邻近桥梁沉降变形影响显著,通过设置分隔墙分区开挖及MJS工法墙进行变形控制,能够较好地控制基坑的空间效应,减少“长边效应”、“异形效应”等对桥梁沉降变形的影响。通过现场基坑开挖过程实际监测结果,验证这一综合变形控制方案的可行性。该研究成果对于类似复杂地质条件下深大狭长异形基坑的支护及施工设计具有很好的借鉴意义。     

砂土液化大变形本构模型及在ABAQUS软件上的实现

基于Yang和E lgam al等人提出的砂土液化大变形本构模型,对该模型的建立过程进行了详细的推导,基于新的嵌套屈服面硬化规则,对原有模型的硬化规则的不连续性做了改进,把该本构模型扩展应用到三维液化大变形的数值分析中,实现了基于ABAQUS大型商用软件计算平台上砂土液化大变形的计算子程序的开发,基于该计算平台和开发的本构模型,对动三轴试验体系中砂土试样的液化过程进行了数值试验分析,给出了试验过程中试样的竖向动位移、整体竖向应力应变关系滞回曲线和动孔压时程曲线的数值计算结果。文中初步验证了该模型在ABAQUS上开发的子程序的可靠性和数值计算模型的可行性,模型的可靠性及其子程序的稳定性还需通过试验结果和数值计算结果的对比分析与进一步验证。     

黔东南石英脉型金矿毒砂Re-Os同位素定年及其地质意义

黔东南石英脉型金矿床是雪峰多金属成矿带的重要组成部分,有较好的找矿前景,但对该区成矿理论的认识,特别是在成矿物质来源、成矿时代以及成矿动力学背景的认识上仍存在很大分歧.本次研究分别对该区两个主要金矿床(平秋、金井)的载金矿物——毒砂进行了Re-Os同位素定年研究.测试结果表明,平秋金矿蚀变岩型毒砂等时线年龄为400±2...     

栖霞组和茅口组等厚图:对峨眉山地幔柱成因模式的指示意义

对峨眉山大火成岩省(ELIP)及周边地区的栖霞组和茅口组地层进行厚度统计,并利用Surfer软件分别绘制等厚图.栖霞组和茅口组等厚图表明,峨眉山地幔柱导致的隆升可能在栖霞期已开始.茅口组顶部普遍存在平行不整合界面,说明广大区域内的茅口组地层均曾抬升为陆并遭受剥蚀,与CampbeU和Griffiths提出的经典地幔柱模型相吻合.永仁-大姚-楚雄-石屏以及宜良-曲靖一带存在二叠系地层缺失区域,可能是地壳隆升幅度最大地区.利用实验模型推导出ELIP的最大隆升幅度为1500m,与前人利用沉积学推算的结果基本一致.茅口组差异剥蚀指示的地幔柱中心地区与放射状基性岩墙群收敛中心吻合.隆起幅度最大的中心区域存在海相玄武岩喷发现象则可能是隆升之后快速沉降造成的,并不能作为否定曾经发生隆起的证据.     

梧桐庄矿新增大口径3号排水孔施工技术

介绍了梧桐庄矿大口径排水孔钻探成井、固井施工技术。该孔设计孔深646 m,终孔直径520 mm,落点坐标水平位移≯5 m,下入重达90余吨的Φ426 mm套管646 m,水泥固井。由于钻孔直径大,垂直度要求高,施工难度大,预防钻孔超斜、确保顺利安全下入Φ426 mm套管并固井是关键。通过采用小口径先导孔钻进再扩孔成井的施工方法,并采取合理的钻具组合和泥浆,制定有效的防斜技术和下套管措施等,顺利完成了施工任务,施工质量满足设计要求。     

大口径取心工艺在刚果(金)某矿区的应用

为了满足选冶试验矿样质量的需要,刚果（金）Sicomines铜钴矿区选用了大口径取心（≥Φ325 mm）钻探工艺。实际应用表明,针对完整或破碎地层条件选用不同的筒状钻具及取心工艺是大口径取心工程成功的关键。     

核电站扩建工程基坑开挖爆破振动安全控制

结合秦山核电二期扩建工程,在已运行核电站附近新扩建核电站的大型基坑开挖过程中进行爆破振动的监测与爆破振动的控制。通过理论分析与监测等多种手段对爆破振动进行有效的控制,确保了正在运行核电站的安全。所总结的减震措施经验对其他核电站的爆破振动控制具有借鉴作用。     

娄江特大桥深孔泵吸反循环工艺的改进

随着国家基础设施投入的加大,桩径1000－2000 mm、孔深100－130 m的钻孔灌注桩在各类工程中屡被采用。泵吸反循环传统上被用于孔深不超过80 m的深孔,在京沪高铁第六标段娄江特大桥钻孔灌注桩施工中,通过对现有的反循环钻机进行改进,很大程度上提高了泵吸反循环的工作效率,顺利地完成了孔深131 m、桩径1.8 m桩孔的施工,产生了很好的经济效益。