Process and joint quality of ultrasonic vibration enhanced friction stir lap welding

In order to improve the process effectiveness and joint quality, ultrasonic vibrations were integrated with friction stir lap welding. Effect of ultrasonic exertion on the process and joint quality of AA 6061-T6 were investigated. Upon ultrasonic exertion, joints owned larger effective lap width, shorter hooks and improved strength. Weld fracture mode changed from a ductile–brittle mixed mode to a more ductile mode while the fracture path shifted from lap interface to beyond the stir zone. Material flow and interface defects were characterised using lap welded dissimilar aluminium alloy joints. Ultrasonic vibration improved the material flow and reduced the interfacial defects. Variations in failure load of joints were found in accordance with the variations in material flow and interfacial defects.     

Effect of metallurgical evolution during post-weld aging treatment on localised corrosion of resistance spot welding joints of A286 superalloy

The combined effect of resistance spot welding and precipitation hardening on the localised corrosion of A286 superalloy is studied. The specimens tested by double loop electrochemical potentiokinetic reactivation were welded in the solution treated condition, and then subjected to different precipitation hardening treatments. For both base metal and weld nugget, the maximum localised corrosion is reached when η phase is clearly observable. The fact that the localised corrosion resistance of weld nugget is different from that shown by base metal may be explained by the segregation of Ni and Ti towards the interdendritic region of weld nugget (studied by using scanning electron microscope/energy dispersive X-ray analysis).     

钛与低碳钢的电阻点焊

采用电阻点焊方法对纯钛与低碳钢Q235进行焊接试验，利用扫描电子显微镜观察分析了熔核区组织特性，探讨了焊接电流对熔核尺寸和抗剪载荷的影响. 结果表明，受焦耳热的影响熔核直径随焊接电流的增加而增加，抗剪载荷则随焊接电流的增大而呈先升后降的变化趋势，焊接电流为8 kA时所得接头的抗剪载荷最大，约2.85 kN. 在钢侧熔核区观察到了靠近钢侧厚度约为30～50 μm的TiFe2+α-Fe共晶组织层和粗大TiFe柱状晶；钛侧熔核区主要由靠近钛侧约12 μm厚的TiFe+α-Ti共晶组织层和TiFe柱状晶构成，且观察到了宏观分层现象.     

超声功率对2219-T351铝合金搅拌摩擦焊接头组织与性能的影响

采用搅拌摩擦焊和不同功率的超声辅助搅拌摩擦焊对2219-T351铝合金进行焊接试验，测量焊接温度和焊接压力，对焊接接头的微观组织、显微硬度和力学性能进行分析，研究了加入不同超声功率后焊缝的组织性能和材料流动性. 结果表明，超声能降低焊接温度，随着超声功率增加减小的幅度越大. 加入了超声后，焊缝微观组织更加均匀，底部材料的流动情况得到改善，焊缝区有更多的强化相残留，焊接接头的显微硬度、抗拉强度及断后伸长率在加入超声后均有提高，在加入2.25 kW的超声功率时达到最高，最高拉伸强度为331 MPa，可达到母材的80%左右.     

Linear friction welding of Ti6Al4V: experiments and modelling

Linear friction welding of the Ti6Al4V alloy is studied. A new definition of the energy input rate is proposed, based on an integration over time of the in-plane force and velocity; a strong correlation with the upset rate is then found. The effective friction coefficient is estimated to be 0·5±0·1 for varying frequencies and amplitudes, with only a weak dependence on the processing conditions displayed. A model is proposed that accounts for both the conditioning and equilibrium stages of the process, which is shown to be in good agreement with the experimental data. The model is used to study the mechanism by which the flash is formed. A criterion is proposed by which the rippled nature of its morphology can be predicted.     

Condition based maintenance of the two-beam laser welding in high volume manufacturing of piezoelectric pressure sensor

Two-beam laser welding (TBLW) is an advanced process for precise, low distortion joining of cylindrical miniature parts. The process is composed of a laser source, optics and various actuators, which form a sophisticated system for control and maintenance in high volume manufacturing. A well-established method for identifying welding defects and ensuring welding quality is the monitoring of plasma light emission in TBLW. Although such monitoring systems can detect a change in process status, they are not able to diagnose the nature of the fault. The main challenge in this research was to extend the use of quality-based monitoring systems to measure additional deterioration-related parameters and to estimate system deterioration from them by using expert knowledge.This paper shows a novel condition-based maintenance (CBM) for the TBLW system, which performs condition identification using online monitoring of plasma light emission in combination with offline inspection of the seam macrographs. A combination of quality parameters derived from seam macrographs of defective parts is used to identify process deterioration, such as contamination of the optics, misalignment of the optomechanical system, or reduced laser power. The information obtained is used to make predefined process adjustments based on expert domain knowledge. The implementation of the developed CBM in high volume manufacturing of piezoelectric pressure sensors resulted in more predictable TBLW by reducing system failures as well as shorter diagnosis times.     

高频微振辅助工艺对激光焊接接头组织性能的影响

基于自主搭建的高频微振平台，进行316L不锈钢振动辅助激光焊接试验，探究高频微振激光焊接工艺对接头组织性能的影响. 结果表明，施加振动后，焊缝表面无飞溅，成形良好. 截面未出现塌陷、堆高，背部熔宽均匀. 振动的施加，能够明显细化焊缝区的晶粒，在共振频率1 467.5 Hz的高频微振激光焊条件下，晶粒尺寸最小. 点状颗粒物分布在奥氏体晶粒间，趋于弥散，新相及大颗粒物减少. 随着振动频率增加，焊缝区显微硬度值跟着增加，在较高共振频率显微硬度值增加显著，在共振频率1 467.5 Hz、加速度160 m/s2条件下，焊缝区平均硬度206 HV，与无振动相比，硬度值增加5.6%.     

H13钢等离子堆焊Ni60A/Cr3C2覆层的磨损及热疲劳性能

采用等离子堆焊技术在H13钢基体表面上制备了Ni60A/Cr₃C₂堆焊覆层,研究了覆层的磨损行为和热疲劳性能。在600 ℃下销盘试验的结果表明,镍基碳化铬复合覆层的耐磨性是Ni60A堆焊覆层的2.8倍和基材H13钢的11.6倍。镍基覆层可以显著降低H13钢的摩擦因数,加入碳化铬则会削弱覆层的摩擦性能。随着磨损的进行,主要磨损机理从氧化磨损演变为磨粒磨损和粘着磨损。在800 ℃到室温下的热疲劳测试结果表明,镍基碳化铬复合覆层在48个热循环后疲劳裂纹达到200 μm,早于镍基覆层的62次。这说明高温氧化促进热疲劳裂纹的产生。碳化铬增强相从镍基上剥离,导致镍基复合覆层热疲劳性能下降。     

A review on ultrasonic spot welding of copper alloys

As a solid state joining process, ultrasonic spot welding has been proven to be a promising technique for joining copper alloys. However, challenges still remain in employing ultrasonic spot welding to join copper alloys. This article comprehensively reviews the current state of ultrasonic spot welding of copper alloys with a number of critical issues including materials flow, plastic deformation, temperature distribution, vibration, relative motion, vertical displacement, interface friction coefficient, online monitoring technique, coupled with the macrostructure and microstructure, the mechanical properties and electrical conductivity. In addition, the future trends in this field are provided.