Energy and cost analysis of a solar-hydrogen combined heat and power system for remote power supply using a computer simulation

A simulation program, based on Visual Pascal, for sizing and techno-economic analysis of the performance of solar-hydrogen combined heat and power systems for remote applications is described. The accuracy of the submodels is checked by comparing the real performances of the system’s components obtained from experimental measurements with model outputs. The use of the heat generated by the PEM fuel cell, and any unused excess hydrogen, is investigated for hot water production or space heating while the solar-hydrogen system is supplying electricity. A 5 kWh daily demand profile and the solar radiation profile of Melbourne have been used in a case study to investigate the typical techno-economic characteristics of the system to supply a remote household. The simulation shows that by harnessing both thermal load and excess hydrogen it is possible to increase the average yearly energy efficiency of the fuel cell in the solar-hydrogen system from just below 40% up to about 80% in both heat and power generation (based on the high heating value of hydrogen). The fuel cell in the system is conventionally sized to meet the peak of the demand profile. However, an economic optimisation analysis illustrates that installing a larger fuel cell could lead to up to a 15% reduction in the unit cost of the electricity to an average of just below 90 c/kWh over the assessment period of 30 years. Further, for an economically optimal size of the fuel cell, nearly a half the yearly energy demand for hot water of the remote household could be supplied by heat recovery from the fuel cell and utilising unused hydrogen in the exit stream. Such a system could then complement a conventional solar water heating system by providing the boosting energy (usually in the order of 40% of the total) normally obtained from gas or electricity.     

All year power supply with off-grid photovoltaic system and clean seasonal power storage

The objective of the project is an all-year secure supply of alternating current based on a solar energy island grid consisting of serial components and seasonal energy storage. Photovoltaic modules, inverters, electrolysers, batteries, hydrogen stores and fuel cells form the basis of the independent power supply system. For this, selected load profiles were analysed and evaluated in theory and practice.The analysis is based on the results of the test runs of the system and the simulations, in which the combined hydrogen-battery-system is compared to the battery system.It was revealed that it is sensible to complement an island grid operating on lead batteries for shortterm energy supply with hydrogen as a long-term store. This ensures a year-round supply security based on solar energy and the extension of the life span of the batteries required for hydrogen-based power stores. The systems based purely on batteries can not provide perfect supply security during long periods of low solar radiation since they do not possess energy stores which allow long-term energy storage.Hence a seasonal energy store, such as hydrogen, is required to guarantee reliable power supply for every day of the year.Autonomous power supply systems with long-term energy stores operate independently from the public grid system and can be implemented without elaborate intelligent energy management. For this, however, the costs of the serial components must be reduced and the efficiency of the system must be improved.     

Impact of hydrogen on the environment

The present work considers the impact of hydrogen fuel on the environment within the cycles of its generation and combustion. Hydrogen has been portrayed by the media as a fuel that is environmentally clean because its combustion results in the formation of harmless water. However, hydrogen first must be generated. The effect of hydrogen generation on the environment depends on the production process and the related by-products. Hydrogen available on the market at present is mainly generated by using steam reforming of natural gas, which is a fossil fuel. Its by-product is CO₂, which is a greenhouse gas and its emission results in global warming and climate change. Therefore, hydrogen generated from fossil fuels is contributing to global warming to the similar extent as direct combustion of the fossil fuels. On the other hand hydrogen obtained from renewable energy, such solar energy, is environmentally clean during the cycles of its generation and combustion. Consequently, the introduction of hydrogen economy must be accompanied by the development of hydrogen that is environmentally friendly. The present work considers several aspects related to the generation and utilisation of hydrogen obtained by steam reforming and solar energy conversion (solar-hydrogen).     

Performance assessment of a direct steam solar power plant with hydrogen energy storage: An exergoeconomic study

Power generation and its storage using solar energy and hydrogen energy systems is a promising approach to overcome serious challenges associated with fossil fuel-based power plants. In this study, an exergoeconomic model is developed to analyze a direct steam solar tower-hydrogen gas turbine power plant under different operating conditions. An on-grid solar power plant integrated with a hydrogen storage system composed of an electrolyser, hydrogen gas turbine and fuel cell is considered. When solar energy is not available, electrical power is generated by the gas turbine and the fuel cell utilizing the hydrogen produced by the electrolyser. The effects of different working parameters on the cycle performance during charging and discharging processes are investigated using thermodynamic analysis. The results indicate that increasing the solar irradiation by 36%, leads to 13% increase in the exergy efficiency of the cycle. Moreover, the mass flow rate of the heat transfer fluid in solar system has a considerable effect on the exergy cost of output power. Solar tower has the highest exergy destruction and capital investment cost. The highest exergoeconomic factor for the integrated cycle is 60.94%. The steam turbine and PEM electrolyser have the highest share of exergoeconomic factor i.e., 80.4% and 50%, respectively.     

Experimental results for hybrid energy storage systems coupled to photovoltaic generation in residential applications

An experimental solar-hydrogen powered residence simulator was built and tested. The system consisted of a solar photovoltaic array connected to an electrolyzer which produced hydrogen as a means of energy storage. The hydrogen was used to produce electricity in a fuel cell that operated in parallel with a battery to meet dynamic power demand similar to that found in residential applications. The study demonstrated the technical feasibility of operating such a system under the simultaneous dynamics of solar input and load. Limitations of current fuel cell and electrolyzer designs, as they pertain to both power delivery and energy storage, were identified. The study also established the need to understand and address dynamic performance in the design and application of solar-hydrogen reversible fuel cell hybrid systems. An economic analysis found that major cost reductions would need to be achieved for such systems to compete with conventional energy storage devices.     

Solar-hydrogen energy system-model applied to isolated island

Comparison between a petroleum energy system and a solar-hydrogen energy system is studied in the case where an industry is newly introduced to an isolated island. Assuming a hybrid energy system composed of petroleum, solar energy, hydrogen energy and electric energy, we investigate an optimum economy with the use of computer-aided LP (Linear Programming) and QP (Quadratic Programming) models taking account of the cost functions originated from the acquisition prices of the primary energy and the transport prices. Furthermore, the modified LP model makes it possible to take account of the uncertainties arising from the acquisition instability and environmental protection. Some conditions are clarified under which the introduction of a solar-hydrogen energy system is highly feasible.     

Thermoeconomic analysis and artificial neural network based genetic algorithm optimization of geothermal and solar energy assisted hydrogen and power generation

The study aims to optimize the geothermal and solar-assisted sustainable energy and hydrogen production system by considering the genetic algorithm. The study will be useful by integrating hydrogen as an energy storage unit to bring sustainability to smart grid systems. Using the Artificial Neural Network (ANN) based Genetic Algorithm (GA) optimization technique in the study will ensure that the system is constantly studied in the most suitable under different climatic and operating conditions, including unit product cost and the plant's power output. The water temperature of the Afyon Geothermal Power Plant varies between 70 and 130 °C, and its mass flow rate varies between 70 and 150 kg/s. In addition, the solar radiation varies between 300 and 1000 W/m² for different periods. The net power generated from the region's geothermal and solar energy-supported system is calculated as 2900 kW. If all of this produced power is used for hydrogen production in the electrolysis unit, 0.0185 kg/s hydrogen can be produced. The results indicated that the overall energy and exergy efficiencies of the integrated system are 4.97% and 16.0%, respectively. The cost of electricity generated in the combined geothermal and solar power plant is 0.027 $/kWh if the electricity is directly supplied to the grid and used. The optimized cost of hydrogen produced using the electricity produced in geothermal and solar power plants in the electrolysis unit is calculated as 1.576 $/kg H₂. The optimized unit cost of electricity produced due to hydrogen in the fuel cell is calculated as 0.091 $/kWh.     

Power management control for off-grid solar hydrogen production and utilisation system

Climate change concerns, increasing global energy demand, coupled with pending peak supply of fossil fuels, calls for development of new power source. The rapid price drops for solar technologies and combined with international and national policy changes makes solar energy more affordable and accessible for widespread adoption. Solar energy also contributes towards the reduction of greenhouse gas emissions. The combination of electrolysis of water and fuel cells, which use hydrogen as an energy carrier extends the utility of the solar energy. For an integrated solar powered hydrogen production, storage and utilisation system, one of the elements that needs to be designed carefully is the power management system. Power management strategy has a complex function in this type of solar hydrogen system. This paper presents a power management strategy based on fuzzy logic technology to address the problems.     

太阳能—氢能系统的发展前景

对太阳能－氢能系统进行了评述。介绍了氢的特点、生产、贮存、输运及应用。对发展太阳能－氢能系统提出了几点建议。     

Large-scale hydrogen energy storage in salt caverns

Large-scale energy storage methods can be used to meet energy demand fluctuations and to integrate electricity generation from intermittent renewable wind and solar energy farms into power grids. Pumped hydropower energy storage method is significantly used for grid electricity storage requirements. Alternatives are underground storage of compressed air and hydrogen gas in suitable geological formations. Underground storage of natural gas is widely used to meet both base and peak load demands of gas grids. Salt caverns for natural gas storage can also be suitable for underground compressed hydrogen gas energy storage. In this paper, large quantities underground gas storage methods and design aspects of salt caverns are investigated. A pre-evaluation is made for a salt cavern gas storage field in Turkey. It is concluded that a system of solar-hydrogen and natural gas can be utilised to meet future large-scale energy storage requirements.     

Cost analysis of off-grid renewable hybrid power generation system on Ui Island,South Korea

Diesel engine power plants are still widely used on many remote islands in South Korea, despite their disadvantages. Aiming to solve economic and environmental pollution problems, a remote island case study was conducted on Ui Island, aiming to offer a zero-emissions solution by using renewable energy sources in an off-grid application. Power was generated from solar, wind, and hydrogen sources. Li-ion batteries and hydrogen were used as energy storage systems. In addition, PV/battery, wind/battery, PV/wind/battery, PV/battery/PEMFC, wind/battery/PEMFC, and PV/wind/battery/PEMFC systems were simulated using the HOMER software to determine the optimal sizes and techno-economic feasibility. The results show that the PV/wind/battery/PEMFC system is the best system. The configuration of the system consists of 990-kW PV panels, 700-kW wind turbines, a 1088-kWh Li-ion battery bank, 534-kW converter, 300-kW PEMWE system, 300-kg hydrogen tank, and 100-kW PEMFC system. The total NPC of the system is $5,276,069, and the LCOE is 0.366 $/kWh.     

A theoretical study of molten carbonate fuel cell combined with a solar power plant and Cu–Cl thermochemical cycle based on techno-economic analysis

A novel power and hydrogen coproduction system is designed and analyzed from energetic and economic point of view. Power is simultaneously produced from parabolic trough collector power plant and molten carbonate fuel cell whereas hydrogen is generated in a three-steps Cu–Cl thermochemical cycle. The key component of the system is the molten carbonate fuel cell that provides heat to others (Cu–Cl thermochemical cycle and steam accumulator). A mathematic model is developed for energetic and economic analyses. A parametric study is performed to assess the impact of some parameters on the system performance. From calculations, it is deduced that electric energy from fuel cell, solar plant and output hydrogen mass are respectively 578 GWh, 25 GWh and 306 tons. The overall energy efficiency of the proposed plants is 46.80 % and its LCOE is 7.64 c€/kWh. The use of MCFC waste heat allows increasing the solar power plant efficiency by 2.15 % and reducing the annual hydrogen consumption by 3 %. Parametric analysis shows that the amount of heat recovery impacts the energy efficiency of fuel cell and Cu–Cl cycle. Also, current density is a key parameter that influences the system efficiency.     

太阳能驱动的固体氧化物电解池制氢系统性能研究

采用太阳能驱动电解水制氢是实现将太阳能转换为氢能来存储的最佳方式。该文提出一种采用光伏、光热协同驱动固体氧化物电解池（SOEC）进行高温蒸汽电解的制氢系统。建立各子系统数学模型,选取北京地区夏至日气象参数,分析太阳辐照度对制氢系统的性能影响,最后对整个系统进行能量及火用分析。结果表明,电流密度和温度是影响SOEC工作的重要因素。在电流密度较大的情况下升高温度,将有利于提高电解效率。耦合太阳能后系统最大能量及火用效率分别达到19.1%和20.3%。火用分析结果表明系统最大有用功损失发生在光电转换过程,火用损比例为87%。提升光电效率,将成为提高太阳能-氢能转换效率的关键。     

TRNSYS simulation models for solar-hydrogen systems

A solar-hydrogen system is a kind of stand-alone power system (SAPS), which can supply low energy dwellings with energy. With TRNSYS (a transient system simulation program) it is possible to perform parametric studies to find possible system configurations for different climates and loads. The systems simulated in this study consist of a photovoltaic (PV) cell array, an electrolyzer, a hydrogen (H₂) storage, a fuel cell, a catalytic burner, a lead-acid battery, DC/DC converters, DC/AC inverters, diodes, a solar collector, and a water storage tank. The main equations for the PV cell, electrolyzer and fuel cell are provided, while the other models are only briefly described. Simulations are performed for conventional low energy dwellings located in northern latitudes and results for different system configurations and operation schemes are given. The results show that the size of the solar-hydrogen system for a conventional low energy house located in Trondheim, Norway (63°N), needs to be quite large. This is mainly due to the somewhat high energy requirements assumed, but also due to the low insolation available. Simulations of the same dwelling located in lower latitudes, in more favorable climates, and/or with lower energy needs (e.g., future dwellings), show how the size of the solar-hydrogen system can be significantly reduced. The study also illustrates the importance of minimizing the thermal and electrical loads before designing a solar-hydrogen system for energy self-sufficient buildings.     

Simulation,economic and environmental evaluations of green solar parking (refueling station) for fuel cell vehicle

Energy storage is needed for renewable systems due to the intermittent nature of wind and solar energy. Hydrogen can be used to store variable renewable energy such as solar and wind energy. According to this fact, there is an increasing interest in use of solar-hydrogen systems for power supply in remote areas or other standalone applications. One of these applications is Hydrogen production station working by solar energy to use in fuel cell vehicle. Time consuming aspect of solar-hydrogen production is the most prominent reason for presenting a new scheme as a parking-refueling station for fuel cell vehicles in this study. To do this, Simulation, economic and environmental evaluations of the solar parking-refueling station are considered in this article. Because of using an independent hydrogen compression system, the suggested parking-refueling station can be used in a standalone area such as rural and military applications. Results show that the proposed system seems to be economic in present condition. It also illustrates that the Levelized Cost of Product (Km-Passenger) is in a range of 0.15–0.28 US$. Although using the tracker system is not economically efficient, the effect of such a structure is more obvious in the points far from tropical area.     

Dimensionless analysis of the global techno-economic feasibility of solar-hydrogen systems for constant year-round power supply

A novel dimensionless approach to analysing the capability of a solar electricity supply system with seasonal hydrogen storage to supply a constant load throughout the year is presented. The only input required specific to the location is its solar ratio, defined as the minimum daily solar energy input during the year divided by the maximum. As well as yielding an estimate of the saving in installed primary solar electricity generating capacity, the approach gives an indicative evaluation of the economic viability of adding the hydrogen storage to a photovoltaic-based solar supply, either for a large-scale grid or small scale autonomous application. The model has been validated using the results obtained from the more comprehensive RSHAP simulation model (RMIT Solar-Hydrogen Analysis Program). The dimensionless model is applied to a selection of 78 cities with varying latitudes across all five continents. For a round-trip storage efficiency of around 45% and the base-case unit costs of components assumed, solar-hydrogen systems would be economic in 55% of these cities. At 50% storage efficiency and/or lowered unit costs, solar-hydrogen systems would become viable in the vast majority of the cities, excepting those near the equator where the net benefits of adding storage are lower because of the more constant solar radiation over the year.     

Assessment of solar emissions in the climate of Iraq for efficient multifunctional disposal

The concept of solar-hydrogen energy today provides optimal solutions in light of the climate agenda for all geographic areas of the globe.Iraq's geographical location and climate conditions predetermine ample opportunities for renewable sources, namely solar energy. High air temperatures, the prevailing number of sunny days recorded annually in the region, create a favorable technical platform for the implementation of thermal processes based on the utilization of incoming research. Therefore, for the design of solar plants and in the future, a reliable estimate of solar energy resources is required to determine the generated power depending on seasonal changes. Theoretical methods of calculating the incoming radiation flow for a particular area do not have the required accuracy for a number of reasons, the main of which is the permanent state of cloud cover. Only taking into account the actual climatic conditions for the construction areas under consideration on the basis of long-term actinometric observations gives a fairly accurate distribution of solar energy. The absence of such information in full implies forecasting of resource availability, including for areas not covered by observation systems. Given these limitations, an analysis of the average monthly daily solar radiation revenues for densely populated areas of Iraq is provided. On the basis of actinometric information of many years of observations, dependencies were obtained to determine the solar energy coming at statistical clouds per day per 1 m² of horizontal surface of the area, taking into account its latitude and serial number of the month of the year. The equations allow to fulfill the forecast of the area irradiation for the design of solar plants, to justify the subsequent efficiency of the alternative system, as well as the level of possible replacement of traditional resources and the degree of reduction of their consumption. On the basis of the calculated data, it is possible to justify the most expedient scheme of solar energy utilization depending on the available resources and to select the structures of radiation sensing devices required for climatic conditions for the solved tasks. In view of the analysis of solar energy distributions and average monthly outdoor air temperatures in Iraq, two types of thermal solar plants have been recommended for use, which may have additional circuits for generating electricity and cold. In addition, the fixed irradiation potential of the territories makes it possible to carry out an effective passive transmission to maintain the thermophilic mode of anaerobic fermentation of organic waste. In this case, environmentally friendly utilization of carbon-containing substrates is accompanied by an increase in the rate of formation of biogas, and therefore hydrogen, without the use of traditional heat supply to reactors.     

From solar to hydrogen: Preliminary experimental investigation on a small scale facility

Issues of exhaustible natural resources, fluctuating fossil fuel prices and improvements in electric power systems motivated governments to behave positively toward the development of distributed generation. In addition, progresses in small size generation technologies and storage systems give rise to a significant diffusion in microgrids, working together with conventional power grid. Indeed, in the next future, domestic microgrids are expected to play a fundamental role in electric power networks, driving both the academic and industrial research interests in developing high efficient and reliable conversion and storage technologies.In this context, this study presents a feasible configuration of a solar-hydrogen integrated microgrid and documents the procedure to characterize the overall efficiency of a laboratory scale test facility. Experimental results highlight that the most significant inefficiencies in the solar to hydrogen conversion process are mainly attributed to the solar to electrical energy conversion process, being responsible for about 89% of losses. The overall laboratory scale solar to hydrogen chain can reach conversion efficiency up to 5.3%.     

A review on coupling Green sources to Green storage (G2G): Case study on solar-hydrogen coupling

The present review paper aims to shed lights on the concept of fully green energy system which includes both the source of energy and the storage system. The objective is to propose an energy label “Green to Green” (G2G) that identifies systems involving simultaneously green source and green storage, as an efficient solution to achieve a significant reduction in the dangerous level of pollution that most countries have reached today. Green sources include mainly renewable energy systems such as solar, wind, geothermal and wave energy systems. In its turns green storage includes pumped hydroelectric, flywheel, hydrogen and compressed air. Moreover, and as a case investigation on G2G concept, the paper reviews the main solar-hydrogen coupling systems, that are categorized within four categories parabolic trough-hydrogen, solar tower-hydrogen, photovoltaic-hydrogen and solar chimney-hydrogen.     

Enhanced generation of hydrogen,power, and heat with a novel integrated photoelectrochemical system

Hydrogen is an essential component of power-to-gas technologies that are needed for a complete transition to renewable energy systems. Although hydrogen has zero GHG emissions at the end-use point, its production could become an issue if non-renewable, and pollutant energy and material resources are used in this step. Therefore, a crucial step for the fully developed hydrogen economy is to find alternative hydrogen production methods that are clean, efficient, affordable, and reliable. With this motivation, in this study, an integrated and continuous type of hydrogen production system is designed, developed, and investigated. This system has three components. There is a solar spectral splitting device (Unit I), which splits the incoming solar energy into two parts. Photons with longer wavelength is sent to the photovoltaic thermal hybrid solar collector, PV/T, (Unit II) and used for combined heat and power generation. Then the remaining part is transferred to the novel hybrid photoelectrochemical-chloralkali reactor (Unit III) for simultaneous H₂, Cl₂, and NaOH production. This system has only one energy input, which is the solar irradiation and five outputs, namely H₂, Cl₂, NaOH, heat, and electricity. Unlike most of the studies in the literature, this system does not use only PV or only a photoelectrochemical reactor. With this approach, solar energy utilization is maximized, and the wasted portion is minimized. By selecting PV/T rather than PV, the performance of the panels is maximized because recovering the by-product heat as a system output in addition to electricity, and the PV/T has less waste and higher efficiency. The present reactor does not use any additional electron donors, so the wastewater discharge is only depleted NaCl solution, which makes the system significantly cleaner than the ones available in the literature. The specific aim of this study is to demonstrate the optimum operating parameters to reach the maximum achievable production rates and efficiencies while keeping the exergy destruction as little as possible. In this study, there are four case studies, and in each case study, one decision variable is optimized to get the desired performance results. Within the selected operating parameter range, all performance criteria (except exergy destruction) are normalized and ranked for proper comparison. The maximum production rates and efficiencies with the least possible exergy destruction are observed at the operating temperature of 30 °C. At 30 °C, 4.18 g/h H₂, 127.55 g/h Cl₂, 151 W electricity, and 716 W heat are produced with an exergy destruction rate of 95.74 W and 78% and 30% energy and exergy efficiencies, respectively.