混合型固化剂对环氧树脂室温和低温力学性能的影响

研究了一种刚性和柔性胺混合型固化剂（芳香胺DETD和聚醚胺D-400）固化环氧树脂浇铸体的力学性能、材料断裂表面的微观形貌和玻璃化转变温度等性能。结果表明:当D-400加入量占固化剂总量的40%时,其室温拉伸强度呈现最大值,为82.52 MPa,弹性模量为2.30 GPa,与未加D-400的体系相比分别提高了6.3%和14.4%,其低温冲击强度提高了14%。对冲击断面形貌进行扫描电子显微分析表明:D-400的加入致使断口形貌变得粗糙,抗开裂能力得到提高。热分析实验结果显示,体系的玻璃化转变温度随着D-400含量的增加而降低。此外,还探讨了环氧树脂体系低温增韧机制。      

柔性胺改性剂对环氧树脂力学性能的影响

以柔性胺D-230作为改性剂,用浇铸成型法制备了环氧树脂结构胶,研究了其力学性能与D-230加入量的关系,并探讨了该材料的微观断裂形貌与韧性的关系.力学测试结果显示室温断裂延伸率、室温和低温冲击韧性随D-230含量的增加而增加,表明D-230对环氧树脂产生有效的增韧作用.当D-230加入量为21%(质量分数)时,室温拉伸强度和弹性模量最大,分别为85.44MPa和3.22GPa,当继续增加D-230的含量时,二者则呈降低的趋势.对拉伸断面形貌进行扫描电子显微(SEM)分析显示,随着D-230含量的增加,断口形貌越粗糙,表明抗开裂能力增加,这与高断裂延伸率和高冲击韧性的结果一致.热分析实验结果显示,体系的玻璃化温度(Tg)随着D-230含量的增加而降低.     

双单倍体牙鲆的性腺发生、性别分化及早期发育的研究

本文利用组织切片的方法研究了双单倍体牙鲆的性腺发生、性别分化及早期发育。结果显示:双单倍体牙鲆中除雌性外,还有雄性和未分化鱼出现,所占比例分别为56%、38%和6%。双单倍体牙鲆雌性的性别分化晚于普通牙鲆。雌鱼至100日龄,卵巢腔仍未闭合;110日龄雌鱼的产卵板上存在大量向卵母过渡的卵原细胞,未见Ⅰ时相卵母细胞出现。双单倍体牙鲆雄鱼精巢的分化在时间上和普通牙鲆的基本相同。随着发育的进行,双单倍体牙鲆雌鱼的卵巢出现部分异常的卵母细胞以及卵巢退化现象;部分雄鱼的精巢也有退化现象出现。9～11月龄,双单倍体牙鲆雄鱼的精巢发育到Ⅲ期,而普通牙鲆性腺在同期进入了Ⅳ期;11月龄开始双单倍体牙鲆雄鱼精巢有退化的迹象;13～15月龄,精巢退化成精小叶,其中只含有精原细胞,初级精母细胞消失不见,似Ⅱ期精巢。     

室温氧化发黑剂的研制

采用正交试验法筛选配方 ,研制出节能、降耗、减污的钢铁室温氧化发黑剂 ;通过配方组分中各成分对氧化膜性能的影响分析 ,得出了CuSO4 ·5H2 O·H2 SeO3·Zn(H2 PO4 ) 2 、NiCl2 、pH值和氧化时间对膜层性能的影响规律 ,并进一步探讨了室温氧化机理。     

浸入沉淀相转化法制膜

综述了近期关于浸入沉淀相转化法制备聚合物分离膜的理论和实验研究工作,对浸入沉淀相转化法制备聚合物分离膜的过程热力学、发生的各种相转变（液－液分相,聚合物的结晶、凝胶化和玻璃化转变等）、成膜机理和膜结构形态进行了分析。并对影响膜结构形态的因素如聚合物的选择、聚合物的浓度、溶剂／非溶剂体系的选择、制膜液的组成、凝胶浴的组成等进行了讨论。     

常温固化型磷酸盐耐热涂料的研制

研究了一种用于钢铁表面的磷酸盐复合涂料,它由复合磷酸盐基液、耐热颜料和一定的添加剂组成,涂刷在普通钢铁表面上可在室温自然固化。该涂料不须加固化剂。对涂膜性质的研究表明,其成膜机理可分为两段：低温磷化－水解,高温缩聚交联。     

Ti6Al4V表面纳米多孔氧化膜的电解制备及形成机理研究

在(NH4)2SO4/NH4F电解液中,采用阶段升压至预定电压,然后恒压阳极氧化在Ti6Al4V表面制备出纳米多孔氧化膜。利用SEM、XRD对纳米多孔氧化膜进行表征。研究表明,电解液pH值和外加电压对纳米多孔氧化膜形成和形貌影响非常大。电解液的pH值=4.0,恒压为20V时,形成孔均匀规整的纳米多孔氧化膜,孔内径约为85nm。纳米多孔氧化膜形成机理是:首先钛合金表面钝化,在F-作用下钝化表面发生孔蚀而形成原始胚胎孔,然后胚胎孔处氧化膜在电场支持下发生场致溶解而成大孔。     

Ti6A14V表面纳米多孔氧化膜的电解制备及形成机理研究

在(NH4)2SO4/NH4F电解液中,采用阶段升压至预定电压,然后恒压阳极氧化在Ti6A14V表面制备出纳米多孔氧化膜.利用SEM、XRD对纳米多孔氧化膜进行表征.研究表明,电解液pH值和外加电压对纳米多孔氧化膜形成和形貌影响非常大.电解液的pH值=4.O,恒压为20V时,形成孔均匀规整的纳米多孔氧化膜,孔内径约为85nm.纳米多孔氧化膜形成机理是:首先钛合金表面钝化,在F-作用下钝化表面发生孔蚀而形成原始胚胎孔,然后胚胎孔处氧化膜在电场支持下发生场致溶解而成大孔.     

热塑性结晶型全芳族聚酯酰亚胺的制备与聚集态结构

以对-亚苯基-双苯偏三酸酯二酐(BTAH)与4,4'-二胺基二苯醚(ODA)为单体采用两步法合成了一种全芳族热塑性结晶型聚酯酰亚胺.盖示扫描量热(DSC)结果显示其玻璃化转变温度为192℃,且聚合物在熔融过程中表现出熔融双峰.X射线衍射(WAXD)结果显示聚合物在室温以及在410℃和420℃处理后均在2θ为18°,23...     

牙鲆生长激素基因的克隆及其在大肠杆菌中的融合表达

采用逆转录聚合酶链式反应(RT-PCR)方法,从牙鲆(Paralichthys olivaceus)脑垂体总RNA中扩增出编码牙鲆生长素(GH)成熟肽基因序列。重组至融合表达载体pGEX-4T-3中,构建成牙鲆GH基因融合表达载体pGEX-gh,转化大肠杆菌BL21(DF3),筛选阳性克隆,IVIG诱导表达。经SDS-PAGE电泳显示在45kD处有特异的蛋白条带出现,该蛋白的表达量随诱导时间的延长而增加,3h达最高值,达到细胞总蛋白的18．3％。该融合蛋白在胞内主要以包涵体状态存在,经优化表达条件,成功地获得了可溶性的融合蛋白,经Glutathione Sepharase 4B凝胶纯化后用Western-blotting检测表明其为牙鲆生长激素,并通过酶联免疫吸附受体法证实其具有生物学活性。     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.