PP/HDPE/SBS三元共混物的研究——基体韧性和弹性体分散相对PP三元共混物脆—韧转变的影响

研究了固定PP/HDPE/SBS三元共混物配比,采用不同共混工艺条件下的脆-韧转变规律。研究表明:PP三元共混物的冲击强度与SBS分散相粒径有密切关系。当SBS分散相粒间距T等于临界值T_c时,PP三元共混物将发生脆-韧转变。研究还表明基体韧性与T_c有密切关系,当基体韧性增高时,T_c值将增大。     

PP／HDPE／SBS三元共混物的研究——形态结构与性能

研究了PP/HDPE/SBS三元共混物的性能及形态结构特征。研究结果表明,PP三元共混物的冲击韧性除与SBS的含量密切相关外,还与HDPE的含量有关,HDPE起到了与SBS相似的增韧作用。由于HDPE的掺入,减少了SBS的含量,制成了一种力学性能均衡的超高韧性PP三元共混材料。形态结构的研究表明,共混物中,SBS呈颗粒状分布,另外SBS还与HDPE组成了具有包藏结构的复合粒子。     

PP/EPDM/纳米弹性体粒子三元共混体系的脆韧转变

研究了PP／EPDM／纳米弹性体粒子(ENP)三元共混体系的脆韧转变行为。结果表明，与PP／EPDM二元共混物相比，三元共混物的脆韧转变可以在EPDM质量分数较低的情况下发生；在橡胶总质量分数相同的情况下，三元共混物有更高的冲击强度，拉伸强度有一定提高。从脆断样条的扫描电镜照片观察到，在相同EPDM质量分数下，PP／EPDM／ENP三元共混物中的EPDM粒子明显细化，分布均一，粒子间距减小，这是脆韧转变提前的原因。     

Structure and properties of PP/POE/HDPE blends

This work was aimed to counteract the effect of ethylene‐α‐olefin copolymers (POE) by reinforcing the polypropylene (PP)/POE blends with high density polyethylene (HDPE) particles and, thus, achieved a balance between toughness and strength for the PP/POE/HDPE blends. The results showed that addition of HDPE resulted in an increasing wide stress plateau and more ductile fracture behavior. With the increase of HDPE content, the elongation at break of the blends increased rapidly without obvious decrease of yield strength and Young's modulus, and the notched izod impact strength of the blends can reach as high as 63 kJ/m² at 20 wt % HDPE loading. The storage modulus of PP blends increased and the glass transition temperature of each component of the blends shifted close to each other when HDPE was added. The crystallization of HDPE phase led to an increase of the total crystallinity of the blend. With increasing HDPE content, the dispersed POE particle size was obviously decreased, and the interparticle distance was effectively reduced and the blend rearranged into much more and obvious core‐shell structure. The fracture surface also changed from irregular striation to the regularly distant striations, displaying much obvious character of tough fracture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Brittle-ductile transition in PP/EPDM blends: effect of notch radius

The toughness of polypropylene (PP)/ethylene-propylene-diene monomer (EPDM) blends was studied over wide ranges of EPDM content and temperature. In order to study the effect of notch radius (R), the toughness of the samples with different notch radii was determined from Izod impact test. The results showed that both toughness and brittle-ductile transition (BDT) of the blends were a function of R, respectively. At test temperatures, the toughness tended to decrease with increasing 1/R for various PP/EPDM blends. Moreover, the brittle-ductile transition temperature (T_BT) increased with increasing 1/R, whereas the critical interparticle distance (ID_c) reduced with increasing 1/R. Finally, it was found that the different curves of ID_c versus test temperature (T) for different notches reduced down to a master curve if plotting ID_c versus T_BT^m-T, where T_BT^m was the T_BT of PP itself for a given notch, indicating that T_BT^m-T was a more universal parameter that determined the BDT of polymers. This conclusion was well in agreement with the theoretical prediction.     

Brittle-ductile transition of particle toughened polymers: influence of the matrix properties

It was theoretically pointed out that the product of the yield stress and yield strain of matrix polymer that determined the brittle-ductile transition (BDT) of particle toughened polymers. For given particle and test condition, the higher the product of the yield stress and the yield strain of the matrix polymer, the smaller the critical interparticle distance (ID_c) of the blends was. This was why the ID_c (0.15 μm) of the polypropylene (PP)/rubber blends was smaller than that (0.30 μm) of the nylon 66/rubber blends, and the ID_c of the nylon 66/rubber blends was smaller than that (0.60 μm) of the high density polyethylene (HDPE)/rubber blends.     

Studies on binary and ternary blends of polypropylene with SEBS,PS, and HDPE. II. Tensile and impact properties

Studies are reported on tensile and impact properties of several binary and ternary blends of polypropylene (PP), styrene-b-ethylene-co-butylene-b-styrene triblock copolymer (SEBS), high-density polyethylene (HDPE), and polystyrene (PS). The blend compositions of the binary blends PP/X were 10 wt % X and 90 wt % PP, while those of the ternary blends PP/X/Y were 10 wt % of X and 90 wt % of PP/Y, or 10 wt % Y and 90 wt % PP/X (PP/Y and PP/X were of identical composition 90:10); X, Y being SEBS, HDPE, or PS. The results are interpreted for the effect of each individual component by comparing the binary blends with the reference system PP, and the ternary blends with the respective binary blends as the reference systems. The ternary blend PP/SEBS/HDPE showed properties distinctly superior to those of PP/SEBS/PS or the binary blends PP/SEBS and PP/HDPE. Differences in the tensile yield behavior of the different samples and their correlation with impact strength suggested shear yielding as the possible mechanism of enhancement of impact strength. Scanning electron microscopic study of the impact fractured surfaces also supports the shear yielding mechanism of impact toughening of these blends.     

Toughening of recycled polystyrene used for TV backset

The recycled polystyrene (rPS) was toughened with ethylene‐octylene copolymer thermoplastic elastomer (POE) and high‐density polyethylene (HDPE) with various melt flow index (MFI), compatibilized by styrene‐butadiene‐styrene copolymer (SBS) to enhance the toughness of rPS for use as TV backset. The rPS/POE binary blends exhibited an increased impact strength with 5–10 wt % POE content followed by a decrease with the POE content up to 20 wt %, which could be due to poor compatibility between POE and rPS. For rPS/POE/SBS ternary blends with 20 wt % of POE content, the impact strength increased dramatically and a sharp brittle‐ductile transition was observed as the SBS content was around 3–5 wt %. Rheological study indicated a possible formation of network structure by adding of SBS, which could be a new mechanism for rPS toughening. In rPS/POE/HDPE/SBS (70/20/5/5) quaternary blends, a fibril‐like structure was observed as the molecular weight of HDPE was higher (with lower MFI). The presence of HDPE fibers in the blends could not enhance the network structure, but could stop the crack propagation during fracture process, resulting in a further increase of the toughness. The prepared quaternary blend showed an impact strength of 9.3 kJ/m² and a tensile strength of 25 MPa, which can be well used for TV backset to substitute HIPS because this system is economical and environmental friendly. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rubber toughened semicrystalline PET: influence of the matrix properties and test temperature

This article is concerned with the effect of the inherent matrix properties (matrix molar mass and crystallinity) as well as the temperature on the impact behaviour of rubber toughened semicrystalline polyethylene terephthalate (PET). The dispersed phase consists of a blend of an ethylene-co-propylene rubber (EPR) and a copolymer of ethylene and 8 wt% glycidyl methacrylate (E-GMA8) acting as a compatibilising agent, leading to PET/(EPR/E-GMA8) blends. The influence of the matrix molar mass on the impact behaviour of rubber toughened PET is found to primarily originate from its effect on the blend phase morphology, rather than from an inherent effect of the molar mass itself. The dispersed phase particle size is seen to decrease with increasing PET molar mass. A direct correlation between the impact strength and the interparticle distance could be established. A critical interparticle distance (ID_c) of 0.1 μm could be determined, independent of the PET molar mass. The brittle-ductile transition temperature (T_bd) of the blends with a varying matrix molar mass also displayed a strong correlation with the interparticle distance, independent of the matrix molar mass. However, this correlation appears to depend on the crystalline characteristics of the PET matrix material since an incompletely crystallised PET matrix leads to an increase of the T_bd.     

Glass transition behavior of polypropylene/polystyrene/styrene-ethylene-propylene block copolymer blends

Summary The glass transition behavior of ternary blends of polypropylene (PP), polystyrene (PS) and styrene-ethylene-propylene-styrene block copolymer (SEPS) was investigated. The blends were prepared by an internal mixer, and their dynamic mechanical properties and morphology were measured. The blends showed phase inversion at around 75wt% PS composition. The glass transition temperature (T_g) of the PP phase shifted to lower temperature as the PS contents were increased in PP/PS binary blends, probably due to the mismatch of thermal expansion coefficients between two components. As the SEPS copolymer contents were increased, the T_g's of the PP phase in the blends increased. In particular, the large increase in T_g of the PP phase was observed in the PP/PS (25/75) blends where the phase inversion takes place. Received: 2 February 1998/Revised version: 24 March 1998/Accepted: 13 April 1998     

Mechanical and thermal properties of calcium carbonate‐filled PP/LLDPE composite

Polymer blends typically are the most economical means to develop new resins for specific applications with the best cost/performance balance. In this paper, the mechanical properties, melting, glass transition, and crystallization behavoir of 80 phr polypropylene (PP) with varying weights of linear low density polyethylene (LLDPE) at 10, 20/ 20 wt % CaCO₃, 30, 40, and 50 phr were studied. A variety of physical properties such as tensile strength, impact strength, and flexural strength of these blends were evaluated. The compatibility of these composite was examined by differential scanning calorimetry (DSC) to estimate T_m and T_c, and by dynamic mechanical analysis (DMA) to estimate T_g. The fractographic analysis of these blends was examined by scanning electron microscopy (SEM). It has been confirmed that increasing the LLDPE content trends to decreases the tensile strength and flexural strength. However, increasing the LLDPE content led to increases in the impact strength of PP/LLDPE blends. It was also found that up to 40 phr the corresponding melting point (T_m) was not effected with increasing LLDPE content. Each compound has more than one T_g, which was informed that there is a brittle‐ductile transition in fracture nature of these blends, the amount of material plastically deformed on the failure surface seems to increase with the increasing the LLDPE content. And PP/LLDPE blends at temperature (23°C) showed a ductile fracture mode characterized by the co‐existence of a shear yielding process; whereas at lower temperature (−20°C) the fractured surfaces of specimens appear completely brittle. The specimens broke into two pieces with no evidence of stress whitening, permanent macroscopic deformation or yielding. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The experimental results and simulation of temperature dependence of brittle‐ductile transition in PVC/CPE blends and PVC/CPE/nano‐CaCO3 composites

The effect of chlorinated polyethylene (CPE) content and test temperature on the notched Izod impact strength and brittle‐ductile transition behaviors for polyvinylchloride (PVC)/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites is studied. The CPE content and the test temperature regions are from 0–50 phr and 243–363 K, respectively. It is found that the optimum nano‐CaCO₃ content is 15 phr for PVC/CPE/nano‐CaCO₃ ternary composites. For both PVC/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites, the impact strength is improved remarkably when the CPE content or test temperature is higher than the critical value, that is, brittle‐ductile transition content (C_BD) or brittle‐ductile transition temperature (T_BD). The T_BD is closely related to the CPE content, the higher the CPE content, the lower the T_BD. The temperature dependence of impact strength for PVC/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites can be well simulated with a logistic fitting model, and the simulation results can be illustrated with the percolation model proposed by Wu and Jiang. DMA results reveal that both PVC and CPE can affect the T_BD of PVC/CPE blends and PVC/CPE/nano‐CaCO₃ composites. When the CPE content is enough (20 phr), the CPE is more important than PVC for determining the T_BD of PVC/CPE blends and PVC/CPE/nano‐CaCO₃ composites. Scanning electron microscopy (SEM) observations reveal that the impact fractured mechanism can change from brittle to ductile with increasing test temperature for these PVC systems. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of PS/SBS/nano-CaCO3 blends

Abstract

The effect of SBS and nano-CaCO₃ on the mechanical properties of PS blends was studied, and their morphologies were characterised by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Izod impact strengths of notched samples of PS/SBS/CaCO₃ blends with nanometre particles of nano-CaCO₃ and SBS are higher than those of PS and PS/SBS blends with the same content of SBS, and the tensile strengths are higher than those of PS/SBS blends. The inclusion of nano-CaCO₃ within the dispersed phase of SBS enlarges the volume of the domains of SBS, which increases the toughness of the ternary blends (PS/SBS/CaCO₃). The mass ratio of SBS/CaCO ₃ plays an important role in the properties of the ternary blends because it affects the concentration of SBS in these blends, the dispersion of nano-CaCO₃ and the morphology of the ternary blends.     

Blends of i‐PP and SBS. II. Influence of in situ compatibilization on the mechanical properties

This article concerns the in situ compatibilization of immiscible isotatic polypropylene/styrene–butadiene–styrene triblock copolymer blends (i‐PP/SBS) by use of a reactive mixture. For this purpose, maleated PP (PP–MAH) and SBS (SBS–MAH) were used as functionalized polymers and 4,4′‐diaminediphenylmethane was used as a coupling agent between maleated polymers, resulting in a graft copolymer. Binary blends of i‐PP/SBS, nonreactive ternary blends of i‐PP/PP–MAH/SBS, and reactive ternary blends of i‐PP/PP–MAH/SBS–MAH with varying diamine/anhydride molar ratios were prepared. The mechanical properties of the blends were determined by tensile and impact‐resistance tests. The optimum improvement in the mechanical properties was found when the diamine/anhydride molar ratio in the ternary reactive blends was 0.5/1. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 516–522, 2003     

Polyethylene toughened by CaCO3 particle: Brittle-ductile transition of CaCO3-toughened HDPE

The dependencies of the notched Izod impact toughness of HDPE / CaCO₃ blends on CaCO₃ particle concentration and particle size are analyzed. It was found that the notched Izod impact strength (S) of HDPE / CaCO₃ blends depends discontinuously on CaCO₃ particle concentration. A brittle-ductile transition occurs when the CaCO₃ volume fraction (V_f) increases to a critical value (Vη_f). Furthermore, a brittle-ductile transition master curve can be constructed by taking the matrix ligament thickness (L) into account as a parameter instead of V_f. The results show that the critical matrix ligament thickness (L_c) is a single parameter for the transition and L_c = 5.2μm for HDPE / CaCO₃ blends. The impact strength, however, varies considerably with CaCO₃ particle size, which shows that CaCO₃ particle size is another dominating parametor for the toughness of HDPE / CaCO₃ blends. © 1993 John Wiley & Sons, Inc.     

PET/PC blends: Effect of chain extender and impact strength modifier on their structure and properties

Methylene diphenyl diisocyanate (MDI) affects the morphology, rheological, mechanical, and relaxation properties, as well as tendency to crystallize of PET in PET/PC/(PP/EPDM) ternary blends produced by the reactive extrusion. Irrespective of the blend phase structure, the introduction of MDI increases the melt viscosity (MFI dropped), resulting from an increase in the molecular weight of the polymer chains; the PET crystallinity was also reduced. MDI favors compatibility of PET with PC in PET/PC/(PP/EPDM) blends. This is explained by intensified interphase interactions on the level of segments of macromolecules as well as monomer units. The presence of MDI causes a substantial rise in the dynamic shear modulus within the high‐elastic region of PET (for temperature range between T_g,PET and that of PET cold crystallization); the processes of PET cold crystallization and melt crystallization become retarded; the glass‐transition temperatures for PET and PC become closer to each other. MDI affects insignificantly the blend morphology or the character of interactions between the disperse PP/EPDM blend and PET/PC as a matrix. PP/EPDM reduces the intensity of interphase interactions in a PET/PC/(PP/EPDM), but a rise in the degree of material heterogeneity. MDI does not change the mechanism of impact break‐down in the ternary blends mentioned above. Increased impact strength of MDI‐modified materials can be explained by higher cohesive strength and resistance to shear flow at impact loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of PBT/POE-g-GMA/PP ternary blends with good rigidity–toughness balance by core–shell particles

Compared with poly(butylene terephthalate)/glycidyl methacrylate grafted poly(ethylene–octene) (PBT/POE-g-GMA) binary blends, supertough PBT-based ternary blends with little rigidity loss were successfully obtained by adding rigid polypropylene (PP) into PBT/POE-g-GMA blends to construct core–shell particles during melt blending. The effects of PP content and type on the phase morphology and mechanical properties of the blends were systematically investigated. Theoretical predictions and scanning electron microscopy observation showed that a core–shell structure was formed in PBT matrix with PP as the core and POE-g-GMA as the shell. The mechanical property tests showed that POE-g-GMA and PP had significant synergistic toughening effect. When PP with high melt flow index (H-PP) was used, PBT/POE-g-GMA/H-PP (70/15/15) blends possessed the highest Izod notched impact strength, which was 1.9-fold compared with PBT/POE-g-GMA (70/30) binary blends, while the tensile performance loss was little. The essential work of fracture tests was performed to evaluate the fracture resistance of different samples. The results demonstrated that PBT/POE-g-GMA/PP ternary blends possessed much better resistance to crack propagation than PBT/POE-g-GMA binary blends. The decrease of interparticle distance and the fibrillation of core–shell particles activated intense matrix shear yielding, which was the reason for the high crack resistance of ternary blends. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48872.     

Effects of the viscosity ratio on polyolefin ternary blends

Polyolefin binary and ternary blends were prepared from polypropylene (PP), an ethylene–α‐olefin copolymer (mPE), and high‐density polyethylene (HDPE) on the basis of the viscosity ratio of the dispersed phase to the continuous phase. In PP/mPE/HDPE blends, fibrils were observed when the dispersed‐phase (mPE/HDPE) viscosity was less than that of PP, or when the viscosity of mPE was less than that of PP, although the viscosity of mPE/HDPE was greater than that of PP. The notched impact strength and mechanical properties such as the yield strength, flexural modulus, and hardness of PP/mPE binary blends further increased with the addition of HDPE according to the type of HDPE. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 4027–4036, 2004     

Mechanical and thermal properties of high‐density polyethylene toughened with glass beads

Glass beads were used to improve the mechanical and thermal properties of high‐density polyethylene (HDPE). HDPE/glass‐bead blends were prepared in a Brabender‐like apparatus, and this was followed by press molding. Static tensile measurements showed that the modulus of the HDPE/glass‐bead blends increased considerably with increasing glass‐bead content, whereas the yield stress remained roughly unchanged at first and then decreased slowly with increasing glass‐bead content. Izod impact tests at room temperature revealed that the impact strength changed very slowly with increasing glass‐bead content up to a critical value; thereafter, it increased sharply with increasing glass‐bead content. That is, the Izod impact strength of the blends underwent a sharp transition with increasing glass‐bead content. It was calculated that the critical interparticle distance for the HDPE/glass‐bead blends at room temperature (25°C) was 2.5 μm. Scanning electron microscopy observations indicated that the high impact strength of the HDPE/glass‐bead blends resulted from the deformation of the HDPE matrix. Dynamic mechanical analyses and thermogravimetric measurements implied that the heat resistance and heat stability of the blends tended to increase considerably with increasing glass‐bead content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2102–2107, 2003     

Brittle‐Ductile Transition and Toughening Mechanism in POM/TPU/CaCO3 Ternary Composites

Summary: Polyoxymethylene (POM)/elastomer/filler ternary composites were prepared, in which thermoplastic polyurethane(TPU) and an inorganic filler, CaCO₃, were used to achieve balanced mechanical properties of POM. A two‐step processing method, in which the elastomer and the filler were mixed to a masterbatch first and then the masterbatch was melt‐blended with pure POM, was used to obtain a core‐shell microstructure with CaCO₃ covered by TPU. A brittle‐ductile transition phenomenon was observed with increasing TPU content for this ternary system. To better understand the toughening mechanism, we investigated the fractured surface, interparticle distance, and the spherulite size of POM as function of the TPU and CaCO₃ content. The critical TPU content depended on not only the content of CaCO₃, but also the size of CaCO₃ particles. The observed brittle‐ductile transition was discussed based on the crystallinity and spherulite size of POM as well as Wu's critical interparticle distance theory. The results showed that the impact strength of POM/TPU/CaCO₃ ternary system depends on a critical, interparticle distance, which varies from one system to another. The dependence of the impact strength on the spherulite size was considered for the first time, and a single curve was constructed. A critical spherulite size of 40 micron was found, at which brittle‐ductile transition occurs, regardless of the TPU and CaCO₃ content or the size of CaCO₃ particles. Our results indicate that the spherulite size of POM indeed plays a role in determining the toughness, and must be considered when discussing the toughening mechanism.

Izod impact strength vs. the crystal size for POM/TPU blends and POM/TPU/CaCO₃ ternary composites.