基于湿法腐蚀工艺的高性能黑硅光电探测器

采用基于硝酸/氢氟酸/磷酸/硫酸混合液的湿法腐蚀工艺,实现了高吸收效率的黑硅结构的制备与工艺集成,获得了具有近红外响应增强效果的黑硅PIN光电探测器,并与未集成黑硅的PIN光电探测器的性能参数进行了对比测试.测试结果显示,黑硅光电探测器在1 060 nm波长下的响应度达到0.69 A/W(量子效率80.7％),较未集成黑硅的器件提高了 116％;黑硅探测器暗电流小于8 nA,响应时间小于8 ns,电容小于9 pF,与未集成黑硅的器件相当.得益于工艺兼容性,所采用的黑硅技术具有广泛应用于硅基近红外PIN,APD,SPAD,SPM等光电探测器的潜力,可显著提高器件的响应率、量子效率、响应速度、击穿电压温度系数等性能.     

硅光电二极管的新发展

1.硅光电二极管的新发展在各种波长(蓝、近紫外)激光器迅速发展情况下,探测这些波长的激光硅光电二极管有了新的发展。蓝、近紫外激光的新应用是,用可调染料激光器进行吸收研究,对于有机分子键的分解和激光多普勒测速。 2.新产品性能新型的硅光电二极管是通过平面扩散、氧钝化制备的,响应率改进了20％～57％。美国联合探测器技术公司目前已进入试生产。表1是该公司生产的硅光电二极管样品的预计性能,从蓝光到近紫外的激光波长有     

光敏二极管的可靠性和寿命分析

在大量实验的基础上,通过理论分析和数据处理,采用威布尔概率纸图估法,评估了为某种设备的特殊需要生产的一种新型硅光电探测器的可靠性和寿命。在正常工作条件(300K)时,器件的平均寿命为1.04×108h;在40℃时,器件的失效率等级达到国家标准规定6级。详细分析了光敏二极管的失效模式及失效机理,提出了提高光敏二极管的可靠性和寿命的措施。     

1 550 nm升频单光子探测器的特性分析

分析了一种工作波长为1550 nm,利用铌酸锂周期极化波导和硅雪崩二极管构成的升频单光子探测器的性能,给出了应用这种探测器的理想通信系统的结构组成,讨论了升频单光子探测器主要参数:量子效率和暗记数及其与泵浦功率的关系.通过比较得出升频探测器优于传统的InGaAs/InP雪崩二极管单光子探测器,能很好地改善量子通信系统的性能.     

一种新型的微流体测量芯片的设计

介绍了一种新型的集成反熔丝和光敏二极管的微流体测量芯片的设计。将反熔丝发光二极管及光敏接收二极管集成到微流体装置可以通过结合集成电路技术和微加工技术来实现。这种新型的微流体芯片包括一个光敏二极管探测器,硅微通道和一个纳米级的反熔丝发光二极管。还介绍了反熔丝发光二极管的结构及工作原理、芯片的结构和制作方法、芯片的应用及其应用仿真。该芯片结合外流路装置可以检测流体的流速、通道中流体的吸收率、通道中流体在某介质中的折射参数以及液体中的气泡、微粒等。     

激光对光电探测器的损伤阈值研究

本文研究了1.06μm和0.53μm激光对硅pin光电二极管以及硅雪崩光电管的永久性损伤效应,测出了损伤阈值。实验发现,光电探测器的PN结受到激光热烧伤是造成其永久性损伤的重要因素,损伤阈值的大小与激光波长、脉冲宽度以及光电探测器结构有关。     

光通信用的硅基长波长光电探测器

硅基长波长光电探测器是最有希望与微电子集成的一种用于光通信的光电器件。介绍了当前硅基长波长光电探测器的发展现状和趋势,讨论了提高硅基长波长光电探测器性能的途径。     

网格敏感区硅光探测器

研究了网格结构硅光敏二极管，在这种结构中，网格条区为ＰＮ结区，网格孔区为高电阻率衬底材料区。在反向工作电压作用下，网孔区将被耗尽，成为ＰＮ结与表面耗尽区结构统一的光探测器。测量表明，这种结构的器件是一种高响应度、宽光谱范围的光探测器件。     

硅PIN光电探测器

利用成熟的半导体平面工艺,采用高阻硅(Si)单晶,我们已成功地制造了四种光电探测器。1.单个的 Si—PIN 光电二极管2.Si 象限探测器3.Si 光电压探测器4.其它光电二极管列阵     

1.3μm高速PIN光电二极管

综合考虑高速光电探测器的频率特性和响应度,优化设计了GaInAs／InPPIN光电二极管的结构参数,解决了长波长高速光电探测器制作中的关键技术,如高纯、超薄GaInAs／InP材料的液相外延生长、有源区的浅结扩散技术、为降低器件漏电采用的双层钝化膜技术和小光敏面的光耦合技术等,并采用同轴封装结构实现了高速光电探测器的高频封装。研制的GaInAs／InPPIN高速长波长光电探测器的3dB带宽达到20GHz,响应度为0．7A／W,暗电流小于5nA。     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.