A 6.25 Gb/s equalizer in 0.18μm CMOS technology for high-speed SerDes

This paper presents a 0.18μm CMOS 6.25 Gb/s equalizer for high speed backplane communication. The proposed equalizer is a combined one consisting of a one-tap feed-forward equalizer （FFE） and a two-tap half-rate decision feedback equalizer （DFE） in order to cancel both pre-cursor and post-cursor ISI. By employing an active-inductive peaking circuit for the delay line, the bandwidth of the FFE is increased and the area cost is minimized. CML-based circuits such as DFFs, summers and multiplexes all help to improve the speed of DFEs. Measurement results illustrate that the equalizer operates well when equalizing 6.25 Gb/s data is passed over a 30-inch channel with a loss of 22 dB and consumes 55.8 mW with the supply voltage of 1.8 V. The overall chip area including pads is 0.3 × 0.5 mm^2.     

一种应用于无线局域网具有3.01-3.82 GHz频率范围和6.29%调谐增益变化的CMOS LC压控振荡器

A wideband low-phase-noise LC voltage-controlled oscillator （VCO） with low VCO gain （Kvco） vari- ation for WLAN fractional-N frequency synthesizer application is proposed and designed on a 0.13-μm CMOS process. In order to achieve a low Kvco variation, an extra switched varactor array was added to the LC tank with the conventional switched capacitor array. Based on the proposed switched varactor array compensation technique, the measured Kvco is 43 MHz/V with only 6.29% variation across the entire tuning range. The proposed VCO provides a tuning range of 23.7% from 3.01 to 3.82 GHz, while consuming 9 mA of quiescent current from a 2.3 V supply. The VCO shows a low phase noise of-121.94 dBc/Hz at 1 MHz offset, from the 3.6 GHz carrier.     

光模块SMT工艺简霸

本文介绍了用于光模块产品的PCB’A在sMT过程中的工艺难点及其解决方案,希望给业界的同行提供一些借鉴。     

应用于2.4GHz无线传感网的超低功耗射频接收前端设计

This paper presents the design of an ultralow power receiver front-end designed for a wireless sensor network （WSN） in a 0.18 μm CMOS process. The author designs two front-ends working in the saturation region and the subthreshold region respectively. The front-ends contain a two-stage cross-coupling cascaded common-gate （CG） LNA and a quadrature Gilbert IQ mixer. The measured conversion gain is variable with high gain at 24 dB and low gain at 7 dB for the saturation one, and high gain at 22 dB and low gain at 5 dB for the subthreshold one. The noise figure （NF） at high gain mode is 5.1 dB and 6.3 dB for each. The input 1 dB compression point （IPldB） at low gain mode is about -6 dBm and -3 dBm for each. The front-ends consume about 2.1 mA current from 1.8 V power supply for the saturation one and 1.3 mA current for the subthreshold one. The measured results show that, comparing with the power consumption saving, it is worth making sacrifices on the performance for using the subthreshold technology.     

A Secure Adaptive Routing Strategy Using Immune Mechanism in MANET

Many protocols have been proposed to in- crease efficiency and security of traditional protocols in Mobile ad-hoc networks （MANET）, but they are all facing the problem of computation overhead which leads to im- practicability. Adaptive routing strategy （ARS） is a novel routing strategy that switches routing protocol according to the network condition. Though this method alleviates the problem of efficiency, it doesn＇t cover the secure issues. We integrate our security mechanism based on Artificial immune system （AIS）, with adaptive routing strategy to enhance efficiency and security. First we presented a more appropriate definition to the measurement of network con- dition, then we designed a secure adaptive routing strategy based on the definition. At last, we gave a performance analysis to validate the correctness and reliability of our scheme.     

Strain effects on band structure of wurtzite ZnO： a GGA ＋ U study

Band structures in wurtzite bulk ZnO/Zn1-xMgxO are calculated using first-principles based on the framework of generalized gradient approximation to density functional theory with the introduction of the on-site Coulomb interaction. Strain effects on band gap, splitting energies of valence bands, electron and hole effective masses in strained bulk ZnO are discussed. According to the results, the band gap increases gradually with increasing stress in strained ZnO as an Mg content of Znl-xMgxO substrate less than 0.3, which is consistent with the experimental results. It is further demonstrated that electron mass of conduction band （CB） under stress increases slightly. There are almost no changes in effective masses of light hole band （LHB） and heavy hole band （HHB） along [00k] and [k00] directions under stress, and stress leads to an obvious decrease in effective masses of crystal splitting band （CSB） along the same directions.     

应用动态偏置和双环反馈技术的CMOS快速瞬态响应低压差线性稳压器设计

This paper presents a low-dropout regulator （LDO） for portable applications with dual-loop feedback and a dynamic bias circuit. The dual-loop feedback structure is adopted to reduce the output voltage spike and the response time of the LDO. The dynamic bias circuit enhances the slew rate at the gate of the power transistor. In addition, an adaptive miller compensation technique is employed, from which a single pole system is realized and over a 59~ phase margin is achieved under the full range of the load current. The proposed LDO has been implemented in a 0.6μm CMOS process. From the experimental results, the regulator can operate with a minimum dropout voltage of 200 mV at a maximum 300 mA load and IQ of 113μA. The line regulation and load regulation are improved to 0. l mV/V and 3.4 μV/mA due to the sufficient loop gain provided by the dual feedback loops. Under a full range load current step, the voltage spikes and the recovery time of the proposed LDO is reduced to 97 mV and 0.142 μs respectively.     

高效太阳电池硅衬底特性对原子层沉积Al2O3薄膜钝化性能的影响

Atom layer deposition （ALD）-Al2O3 thin films are considered effective passivation layers for p-type silicon surfaces. A lower surface recombination rate was obtained through optimizing the deposition parameters. The effects of some of the basic substrate characteristics including material type, bulk resistivity and surface morphology on the passivation performance of ALD-Al2O3 are evaluated in this paper. Surface recombination velocities of 7.8 cm/s and 6.5 cm/s were obtained for p-type and n-type wafers without emitters, respectively. Substrates with bulk resistivity ranging from 1.5 to 4 Ω · cm were all great for such passivation films, and a higher implied Voc of 660 mV on the 3 Ω · cm substrate was achieved. A minority carrier lifetime （MCL） of nearly 10 μs higher was obtained for cells with a polished back surface compared to those with a textured surface, which indicates the necessity of the polishing process for high-efficiency solar cells. For n-type semi-finished solar cells, a lower effective front surface recombination velocity of 31.8 cm/s was acquired, implying the great potential of （ALD）-Al2O3 thin films for high-efficiency n-type solar cells.     

Ranking Potential Reply-Providers in Community Question Answering System

Community Question Answering （CQA） websites have greatly facilitated users＇ lives, with an increasing number of people seeking help and exchanging ideas on the Internet. This newlymerged community features two characteristics： social relations and an ask-reply mechanism. As users＇ behaviours and social statuses play a more important role in CQA services than traditional answer retrieving websites, researchers＇ concerns have shifted from the need to passively find existing answers to actively seeking potential reply providers that may give answers in the near future. We analyse datasets derived from an online CQA system named ＂Quora＂, and observed that compared with traditional question answering services, users tend to contribute replies rather than questions for help in the CQA system. Inspired by the findings, we seek ways to evaluate the users＇ ability to offer prompt and reliable help, taking into account activity, authority and social reputation char- acteristics. We propose a hybrid method that is based on a Question-User network and social network using optimised PageRank algorithm. Experimental results show the efficiency of the proposed method for ranking potential answer-providers.     

一个全差分可编程的多通道神经信号记录芯片

A multi-channel,fully differential programmable chip for neural recording application is presented.The integrated circuit incorporates eight neural recording amplifiers with tunable bandwidth and gain,eight 4thorder Bessel switch capacitor filters,an 8-to-1 analog time-division multiplexer,a fully differential successive approximation register analog-to-digital converter(SAR ADC),and a serial peripheral interface for communication.The neural recording amplifier presents a programmable gain from 53 dB to 68 dB,a tunable low cut-off frequency from 0.1 Hz to 300 Hz,and 3.77 μVrms input-referred noise over a 5 kHz bandwidth.The SAR ADC digitizes signals at maximum sampling rate of 20 kS/s per channel and achieves an ENOB of 7.4.The integrated circuit is designed and fabricated in 0.18-μm CMOS mix-signal process.We successfully performed a multi-channel in-vivo recording experiment from a rat cortex using the neural recording chip.     

A power-efficient 12-bit analog-to-digital converter with a novel constant-resistance CMOS input sampling switch

Apower-efficient 12-bit40-MS/spipelineanalog-to-digitalconverter（ADC）implementedina0.13 μm CMOS technology is presented. A novel CMOS bootstrapping switch, which offers a constant on-resistance over the entire input signal range, is used at the sample-and-hold front-end to enhance the dynamic performance of the pipelined ADC. By implementing with 2.5-bit-per-stage and a simplified amplifier sharing architecture between two successive pipeline stages, a very competitive power consumption and small die area can be achieved. Meanwhile, the substrate-biasing-effect attenuated T-type switches are introduced to reduce the crosstalk between the two op- amp sharing successive stages. Moreover, a two-stage gain boosted recycling folded cascode （RFC） amplifier with hybrid frequency compensation is developed to further reduce the power consumption and maintain the ADC＇s performance simultaneously. The measured results imply that the ADC achieves a spurious-free dynamic range （SFDR） of 75.7 dB and a signal-to-noise-plus-distortion ratio （SNDR） of 62.74 dB with a 4.3 MHz input signal; the SNDR maintains over 58.25 dB for input signals up to 19.3MHz. The measured differential nonlinearity （DNL） and integral nonlinearity （INL） are -0.43 to ＋0.48 LSB and -1.62 to ＋ 1.89 LSB respectively. The prototype ADC consumes 28.4 mW under a 1.2-V nominal power supply and 40 MHz sampling rate, transferring to a figure- of-merit （FOM） of 0.63 pJ per conversion-step.     

Low power high gain gain-controlled LNA and mixer for GNSS receivers Wei Binbin(魏斌斌)1, Jiang Jinguang(江金光)1,2,3*

A low power high gain gain-controlled LNA ＋ mixer for GNSS receivers is reported. The high gain LNA is realized with a current source load. Its gain-controlled ability is achieved using a programmable bias circuit. Taking advantage of the high gain LNA, a high noise figure passive mixer is adopted. With the passive mixer, low power consumption and high voltage gain of the LNA ＋ mixer are achieved. To fully investigate the performance of this circuit, comparisons between a conventional LNA ＋ mixer, a previous low power LNA ＋ mixer, and the proposed LNA ＋ mixer are presented. The circuit is implemented in 0.18 #m mixed-signal CMOS technology. A 3.8 dB noise figure, an overall 45 dB converge gain and a 10 dB controlled gain range of the two stages are measured. The chip occupies 0.24 mm2 and consumes 2 mA current under 1.8 V supply.     

一种应用于GPS接收机的高线性度SiGe HBT低噪声放大器

A high linearity 1.575 GHz SiGe：HBT low noise amplifier （LNA） for global positioning system applications is described. The bipolar cascoded with an MOSFET LNA was fabricated in a commercial 0.18 μm SiGe BiCMOS process, A resistor bias feed circuit with a feedback resistor was designed for the LNA input transistor to improve its intermodulation and compression performance. The packaged chip tested on board has displayed a noise figure of 1. I 1 dB, a power gain of 18 dB, an output 1 dB compression point of ＋7.8 dBm and an input third-order intercept point of ＋1.8 dBm. The chip occupies a 500 × 560μm^2 area and consumes 3.6 mA from a 2.85 V power supply.     

97dB动态范围、带温度补偿的MEMS电容传感器读出电路

This paper presents a charge-sensitive-amplifier(CSA)based readout circuit for capacitive microelectro-mechanical-system(MEMS)sensors.A continuous-time(CT)readout structure using the chopper technique is adopted to cancel the low frequency noise and improve the resolution of the readout circuits.An operational trans-conductance amplifier(OTA)structure with an auxiliary common-mode-feedback-OTA is proposed in the fully differential CSA to suppress the chopper modulation induced disturbance at the OTA input terminal.An analog temperature compensation method is proposed,which adjusts the chopper signal amplitude with temperature variation to compensate the temperature drift of the CSA readout sensitivity.The chip is designed and implemented in a 0.35 m CMOS process and is 2.1 2.1 mm2in area.The measurement shows that the readout circuitachieves0.9aF/√Hz capacitive resolution,97dBd ynamic range in 100Hz signal bandwidth,and 0.8mV/fF sensitivity with a temperature drift of 35 ppm/℃ after optimized compensation.     

激光定位深亚微米CMOS SRAM单粒子翻转敏感区

The pulsed laser facility for SEU sensitivity mapping is utilized to study the SEU sensitive regions of a 0.18/zm CMOS SRAM cell. Combined with the device layout micrograph, SEU sensitivity maps of the SRAM cell are obtained. TCAD simulation work is performed to examine the SEU sensitivity characteristics of the SRAM cell. The laser mapping experiment results are discussed and compared with the electron micrograph information of the SRAM cell and the TCAD simulation results. The results present that the test technique is reliable and of high mapping precision for the deep submicron technology device.     

用于U波段移动数字电视的宽带大动态范围高线性度射频前端

A wideband large dynamic range and high linearity U-band RF front-end for mobile DTV is introduced,and includes a noise-cancelling low-noise amplifier(LNA),an RF programmable gain amplifier(RFPGA) and a current communicating passive mixer.The noise/distortion cancelling structure and RC post-distortion compensation are employed to improve the linearity of the LNA.An RFPGA with five stages provides large dynamic range and fine gain resolution.A simple resistor voltage network in the passive mixer decreases the gate bias voltage of the mixing transistor,and optimum linearity and symmetrical mixing is obtained at the same time.The RF front-end is implemented in a 0.25 μm CMOS process.Tests show that it achieves an ⅡP3(third-order intercept point) of –17 dBm,a conversion gain of 39 dB,and a noise figure of 5.8 dB.The RFPGA achieves a dynamic range of –36.2 to 23.5 dB with a resolution of 0.32 dB.     

一种电流复用共栅低噪声放大器的低功耗433/915-MHz射频前端的设计

This paper presents a wideband RF front-end with novel current-reuse wide band low noise amplifier(LNA),current-reuse V –I converter,active double balanced mixer and transimpedance amplifier for short range device(SRD) applications.With the proposed current-reuse LNA,the DC consumption of the front-end reduces considerably while maintaining sufficient performance needed by SRD devices.The RF front-end was fabricated in 0.18 μm RFCMOS process and occupies a silicon area of just 0.11 mm2.Operating in 433 MHz band,the measurement results show the RF front-end achieves a conversion gain of 29.7 dB,a double side band noise figure of 9.7 dB,an input referenced third intercept point of –24.9 dBm with only 1.44 mA power consumption from 1.8 V supply.Compared to other reported front-ends,it has an advantage in power consumption.     

一种应用于GNSS接收机的低噪声和低杂散频率综合器

A low phase noise and low spur phase locked loop （PLL） frequency synthesizer for use in global navigation satellite system （GNSS） receivers is proposed. To get a low spur, the symmetrical structure of the phase frequency detector （PFD） produces four control signals, which can reach the charge pump （CP） simultaneously, and an improved CP is realized to minimize the charge sharing and the charge injection and make the current matched. Additionally, the delay is controllable owing to the programmable PFD, so the dead zone of the CP can be eliminated. The output frequency of the VCO can be adjusted continuously and precisely by using a programmable LC-TANK. The phase noise of the VCO is lowered by using appropriate MOS sizes. The proposed PLL frequency synthesizer is fabricated in a 0.18 μm mixed-signal CMOS process. The measured phase noise at 1 MHz offset from the center frequency is -127.65 dBc/Hz and the reference spur is -73.58 dBc.     

用于流水线ADC的频率自适应可编程MDAC电路

A programmable high precision multiplying DAC （MDAC） is proposed. The MDAC incorporates a frequency-current converter （FCC） to adjust the power versus sampling rate and a programmable operational am- plifier （POTA） to achieve the tradeoff between resolution and power of the MDAC, which makes the MDAC suitable for a 12 bit SHA-less pipelined ADC. The prototype of the proposed pipelined ADC is implemented in an SMIC CMOS 0.18 μm 1P6M process. Experimental results demonstrate that power of the proposed ADC varies from 15.4 mW （10 MHz） to 63 mW （100 MHz） while maintaining an SNDR of 60.5 to 63 dB at all sampling rates. The differential nonlinearity and integral nonlinearity without any calibration are no more than 2.2/-1 LSB and 1.6/-1.9 LSB, respectively.