DMOS阈值电压二维模型

提出了DMOS器件的二维阈值电压模型,分析了耗尽层宽度的变化,并得到了模型的数学表达式.模型的解析解与实验结果和二维仿真器MEDICI的数值解相吻合.给出了沟道表面扩散浓度在2.0×1016～10.0×1016cm-3范围内DMOS器件的阈值电压简明计算式.该模型的提出解决了以往所用的DMOS阈值电压模型计算很不准确的问题.     

短沟DMOS阈值电压模型

该文提出了短沟DMOS阈值电压模型。基于沟道区耗尽电荷的二维分布,计算沟道区中耗尽电荷总量,由此给出短沟DMOS阈值电压模型的计算式。该模型的解析解与二维仿真器MEDICI的数值解吻合。分析表明,DMOS沟道长度小于0.80m,就应考虑短沟效应。     

DMOS阈值电压二维模型

提出了DMOS器件的二维阈值电压模型 ,分析了耗尽层宽度的变化 ,并得到了模型的数学表达式 .模型的解析解与实验结果和二维仿真器MEDICI的数值解相吻合 .给出了沟道表面扩散浓度在 2e16～ 10 e 10 16cm-3 范围内DMOS器件的阈值电压简明计算式 .该模型的提出解决了以往所用的DMOS阈值电压模型计算很不准确的问题 .     

DMOS辐照正空间电荷阈值电压模型

提出了一种DMOS辐照正空间电荷闽值电压模型。基于沟道杂质的非均匀分布，借助镜像法，导出辐照正空间电荷与沟道电离杂质的二维场和二维互作用势；求解泊松方程，由此给出DMOS辐照正空间电荷阈值电压模型表示式。该模型的解析解与MEDICI仿真的数值解吻合。     

自对准双扩散MOS器件的阈值电压分析

文章提出了精确描述自对准双扩散MOS器件阀值电压的解析模型，给出了其沟道中杂质的二维分布和源结耗尽层宽度的计算方法；分析了边缘效应对氧化层电容的影响，借助电荷共事模型，建立了反映非均匀沟道中耗尽层电荷变化及其对开启电压影响的阀值电压模型；同时，借助二维仿真器，计算出自对准双扩散MOS器件的阈值电压，其值与解析值相吻合。     

短沟Trench MOSFET阈值电压解析模型

传统MOS器件的阈值电压模型被广泛地用于分析Trench MOSFET的阈值电压,这种模型对于长沟道和均匀分布衬底的MOS器件来说很合适.但是对于Trench MOSFET器件来说却显现出越来越多的问题,这是因为Trench MOSFET的沟道方向是垂直的,其杂质分布也是非均匀的.本文基于二维电荷共享模型,给出了Trench MOSFET的一种新的阈值电压解析模型,该模型反映了器件的阈值电压随不同结构和工艺参数变化的规律,模型的结果和器件仿真软件Sivaco TCAD的仿真结果吻合较好.该模型较好地解决了以往所用的Trench MOSFET阈值电压模型计算不准确的问题.     

一种非对称双栅应变硅HALO掺杂沟道MOSFET阈值电压解析模型

提出了一种非对称双栅应变硅HALO掺杂沟道金属氧化物半导体场效应管结构.该器件前栅和背栅由两种不同功函数的金属构成,沟道为应变硅HALO掺杂沟道,靠近源区为低掺杂区域,靠近漏区为高掺杂区域.采用分区的抛物线电势近似法和通用边界条件求解二维泊松方程,分别求解了前背栅表面势、前背栅表面电场及前背栅阈值电压,建立了双栅器件的表面势、表面电场和阈值电压解析模型.详细讨论了物理参数对解析模型的影响.研究结果表明,该器件能够很好的抑制短沟道效应、热载流子效应和漏致势垒降低效应.模型解析结果与DESSIS仿真结果吻合较好,证明了该模型的正确性.     

掺杂浓度对槽栅nMOSFET特性的影响研究

讨论了槽栅结构nMOSFET的掺杂浓度对器件特性的影响，并通过二维器件仿真程序PISCES—Ⅱ进行了计算模拟比较。结果表明，提高衬底掺杂浓度，能使源漏区与沟道之间的拐角效应增大，对热载流子效应抑制的作用明显；提高沟道掺杂浓度，能减小沟道电荷的调制效应，使阈值电压更好。调节沟道掺杂浓度比调节衬底掺杂浓度对器件的影响更大。     

双栅MOSFET沟道侧壁绝缘柱(DP)表面势解析模型

采用抛物线近似方法求解二维泊松方程,建立了漏端沟道侧壁绝缘柱表面电势解析模型。在该解析模型下,求解了不同漏压下的表面势,并与Atlas仿真结果做对比。比较了在相同条件下,DPDG MOSFET与DG MOSFET的沟道侧壁电势与电场分布。在不同沟道长度下,分析了DPDG MOSFET器件的阈值电压(Vth),亚阈值斜率(SS)以及漏感应势垒降低效应(DIBL),并与DG MOSFET作对比。结果表明,添加绝缘柱DP后,不仅减小了源漏端电荷分享,而且增强了栅对电荷控制,从而改善了器件的DIBL效应,并有效提高了器件的可靠性。     

异质栅非对称Halo SOI MOSFET亚阈值电流模型

在沟道源端一侧引入高掺杂Halo结构的异质栅SOI MOSFET,可以有效降低亚阈值电流.通过求解二维泊松方程,为该器件建立了亚阈值条件下的表面势模型.利用常规漂移.扩散理论,在表面势模型的基础上,推导出新结构器件的亚阈值电流模型.为了求解简单,文中给出了一种分段近似方法,从而得到表面势的解析表达式.结果表明,所得到的表面势解析表达式和确切解的结果高度吻合.二维器件数值模拟器ISE验证了通过表面势解析表达式得到的亚阈值电流模型,在亚阈值区二者所得结果吻合得很好.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.