Pyroelectric properties of BST/PLT composite thick films with addition of xPbO–(1 − x)B2O3 glass

The Ba_xSr_1−xTiO₃ (BST)/Pb_1−xLa_xTiO₃ (PLT) composite thick films (20 μm) with 12 mol% amount of xPbO–(1 − x)B₂O₃ glass additives (x = 0.2, 0.35, 0.5, 0.65 and 0.8) have been prepared by screen-printing the paste onto the alumina substrates with silver bottom electrode. X-ray diffraction (XRD), scanning electron microscope (SEM) and an impedance analyzer and an electrometer were used to analyze the phase structures, morphologies and dielectric and pyroelectric properties of the composite thick films, respectively. The wetting and infiltration of the liquid phase on the particles results in the densification of the composite thick films sintered at 750 °C. Nice porous structure formed in the composite thick films with xPbO–(1 − x)B₂O₃ glass as the PbO content (x) is 0.5 ≥ x ≥ 0.35, while dense structure formed in these thick films as the PbO content (x) is 0.8 ≥ x ≥ 0.65. The volatilization of the PbO in PLT and the interdiffusion between the PLT and the glass lead to the reduction of the c-axis of the PLT phase. The operating temperature range of our composite thick films is 0–200 °C. At room temperature (20 °C), the BST/PLT composite thick films with 0.35PbO–0.65B₂O₃ glass additives provided low heat capacity and good pyroelectric figure-of-merit because of their porous structure. The pyroelectric coefficient and figure-of-merit F_D are 364 μC/(m² K) and 14.3 μPa^−1/2, respectively. These good pyroelectric properties as well as being able to produce low-cost devices make this kind of thick films a promising candidate for high-performance pyroelectric applications.     

Fabrication and characterization of (1−x)SrBi2Ta2O9–xBi3TaTiO9 layered structure solid solution thin films for ferroelectric random access memory (FRAM) applications

We report on the properties of (1−x)SrBi₂Ta₂O₉–xBi₃TaTiO₉ solid solution thin films for ferroelectric non-volatile memory applications. The solid solution thin films fabricated by modified metalorganic solution deposition technique showed much improved properties compared to SrBi₂Ta₂O₉. A pyrochlore free crystalline phase was obtained at a low annealing temperature of 600°C and grain size was found to be considerably increased for the solid solution compositions. The film properties were found to be strongly dependent on the composition and annealing temperatures. The measured dielectric constant of the solid solution thin films was in the range 180–225 for films with 10–50% of Bi₃TaTiO₉ content in the solid solution. Ferroelectric properties of (1−x)SrBi₂Ta₂O₉–xBi₃TaTiO₉ thin films were significantly improved compared to SrBi₂Ta₂O₉. For example, the observed remanent polarization (2P_r) and coercive field (E_c) values for films with 0.7SrBi₂Ta₂O₉–0.3Bi₃TaTiO₉ composition, annealed at 650°C, were 12.4 μC/cm² and 80 kV/cm, respectively. The solid solution thin films showed less than 5% decay of the polarization charge after 10¹⁰ switching cycles and good memory retention characteristics after about 10⁶ s of memory retention. The improved microstructural and ferroelectric properties of (1−x)SrBi₂Ta₂O₉–xBi₃TaTiO₉ thin films compared to SrBi₂Ta₂O₉, especially at lower annealing temperatures, suggest their suitability for high density FRAM applications.     

High-resolution and analytical transmission electron microscopy of epitaxial YBa2Cu3O7−x thin films and YBa2Cu3O7/PrBa2Cu3O7 superlattices

Transmission electron microscopy (TEM) studies of epitaxial YBa₂Cu₃O_7−x thin films and YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices are summarized. High-resolution imaging of cross-sections and plan views and energy-dispersive X-ray microanalysis and electron energy loss spectroscopy in the transmission electron microscope were the methods applied. In the first section results on YBa₂Cu₃O_7−x thin films With varying oxygen stoichiometry deposited onto SrTiO₃ are discussed. Then, YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices deposited onto SrTiO₃ and MgO are investigated. Finally, an interface analysis of high-quality YBa₂Cu₃O_7−x thin films deposited onto sapphire with yttrium-stabilized zirconia buffer layers is presented.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Preparation and characterization of YBa2Cu3O7−x high Tc superconducting thin films deposited by S-gun sputtering

We have prepared YBa₂Cu₃O_7−x high T_c superconducting (HTS) thin films on (100) yttria-stabilized zirconia (YSZ) and LaAlO₃ (LAO) substrates, using a 2 kW S-gun in an off-axis mode. By varying the temperature of the substrates, films with a axis and c axis orientations were readily obtained. The X-ray diffraction pattern and Laue pattern confirmed that films with a axis orientation exhibited a single-crystal texture. All films had a good mirror-like surface. For films grown on YSZ substrates, scanning electron microscopy (SEM) revealed a clear distinction between the surfaces of the films grown at various temperatures (520–780°C). Films grown on LAO substrates exhibited even smoother and flatter surfaces. The SEM changes will be discussed in correlation with J_c. The best HTS thin films were obtained on LAO substrates at a temperature of 820°C, with T_c=89 K and J_c=1×10⁶ A cm^-2 (77 K).     

New transparent conducting MgIn2O4---Zn2In2O5 thin films prepared by magnetron sputtering

New materials for a transparent conducting oxide film are demonstrated. Highly transparent Zn₂In₂O₅ films with a resistivity of 3.9 × 10⁻⁴ Ω cm were prepared on substrates at room temperature using a pseudobinary compound powder target composed of ZnO (50 mol.%) and In₂O₃ (50 mol.%) by r.f. magnetron sputtering. MgIn₂O₄---Zn₂In₂O₅ films were prepared using MgIn₂O₄ targets with a ZnO content of 0–100 wt.%. The resistivity of the deposited films gradually decreased from 2 × 10⁻³ to 3.9 × 10⁻⁴ Ω cm as the Zn/(Mg + Zn) atomic ratio introduced into the films was increased. The greatest transparency was obtained in a MgIn₂O₄ film. The optical absorption edge of the films decreased as the Zn/(Mg + Zn) atomic ratio was increased, corresponding to the bandgap energy of their materials. It was found that the resistance of the undoped Zn₂In₂O₅ films was more stable than either the undoped MgIn₂O₄, ZnO or In₂O₃ films in oxidizing environments at high temperatures.     

Properties of thin In2O3 and SnO2 films prepared by corona spray pyrolysis, and a discussion of the spray pyrolysis process

Thin films of doped In₂O₃ and SnO₂ were prepared by the “corona spray pyrolysis” technique with a deposition efficiency of 80%. The electrical and optical properties of the films were determined. A transmission of 88% in the visible region and an IR reflection of more than 90% were the maximum values obtainable for a doped In₂O₃ film.

A detailed discussion of the physical and chemical processes that occur during spray pyrolysis is presented to aid the understanding of this coating technique.

A minimum temperature of about 350°C for the formation of In₂O₃ was empirically confirmed.

Furthermore the powdery precipitate obtained during deposition of In₂O₃ was clearly identified as polycrystalline In₂O₃ formed by a homogeneous reaction.     

Optical properties of a-(Se70Te30)100−x(Se98 Bi2)x thin films

Measurements of optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary part of the dielectric constant) have been made on a-(Se₇₀Te₃₀)_100−x (Se₉₈Bi₂)_x thin films (where x=0, 5, 10, 15 and 20) of thickness 2000 Å in the wavelength range 450–1000 nm. It is found that the optical bandgap decreases with the increase of Se₉₈Bi₂ concentration in the a-(Se₇₀Te₃₀)_100−x(Se₉₈Bi₂)_x system. The value of refractive index (n) decreases, while the extinction coefficient (k) increases with increasing photon energy. The results are interpreted in terms of concentration of localized states varying effective Fermi level.     

Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

The influence of film structure on In2O3 gas response

This paper reports the influence of In₂O₃ film structure on gas-sensing characteristics measured in steady state and transient modes. Films were deposited by spray pyrolysis from InCl₃–water solutions. Correlation between gas-sensing parameters and structural parameters such as film thickness (20–400 nm), grain size (10–70 nm), refractive index and film texture (I(400)/I(222)) were established. It was shown that grain size and porosity are the parameters of In₂O₃ films that best control gas response to ozone. In the detection of reducing gases, the influence of film structure is less important. Decreases in film thickness, grain size and degree of texture are the best way to decrease time constants of the gas response of In₂O₃-based gas sensors.     

Nanocrystallization of SrBi2Nb2O9 from glasses in the system Li2B4O7---SrO---Bi2O3---Nb2O5

Transparent glasses in the system (100−x)Li₂B₄O₇–x(SrO---Bi₂O₃---Nb₂O₅) (10≤x≤60) (in molar ratio) were fabricated by a conventional melt-quenching technique. Amorphous and glassy characteristics of the as-quenched samples were established via X-ray powder diffraction (XRD) and differential thermal analyses (DTA) respectively. Glass–ceramics embedded with strontium bismuth niobate, SrBi₂Nb₂O₉ (SBN) nanocrystals were produced by heat-treating the as-quenched glasses at temperatures higher than 500 °C. Perovskite SBN phase formation through an intermediate fluorite phase in the glass matrix was confirmed by XRD and transmission electron microscopy (TEM). Infrared and Raman spectroscopic studies corroborate the observation of fluorite phase formation. The dielectric constant (_r) and the loss factor (D) for the lithium borate, Li₂B₄O₇ (LBO) glass comprising randomly oriented SBN nanocrystals were determined and compared with those predicted based on the various dielectric mixture rule formalism. The dielectric constant was found to increase with increasing SBN content in LBO glass matrix.     

Influence of rare-earth oxides on structure and crystallization properties of Bi2O3–B2O3 glass

Bi₂O₃·B₂O₃ glasses doped with rare-earth oxides (RE₂O₃) (RE³⁺ = La³⁺, Pr³⁺, Sm³⁺, Gd³⁺, Er³⁺ and Yb³⁺) were prepared by the melting–quenching method. The relationships between composition and properties were demonstrated by IR, DSC, XRD and SEM analysis. The results show that the network structure resembles that of undoped Bi₂O₃·B₂O₃ glass, composing of [BO₃], [BO₄] and [BiO₆] units. RE₂O₃ stabilizes the glass structure as a modifier. Transition temperature (T_g) increases linearly with cationic field strength (CFS) of RE³⁺. La₂O₃, Pr₂O₃, Sm₂O₃ and Gd₂O₃ are benefit to promote the formation of BiBO₃ crystal. When Er₂O₃ and Yb₂O₃ are introduced, respectively, the main crystal phase changes to Bi₆B₁₀O₂₄. Transparent surface crystallized samples are obtained by reheating at 460–540 °C for 5 h. In this case, needle like BiBO₃ crystal or rare-earth-doped BiBO₃ crystal (Pr_xBi_1−xBO₃ and Gd_xBi_1−xBO₃) are observed, which is promising for non-linear optical application.     

RuO2–TiO2 mixed oxides prepared from the hydrolysis of the metal alkoxides

The hydrolysis of ruthenium alkoxide/titanium tetraethoxide mixtures to gels and powders containing 30–40 mol% Ru was investigated. Basic or neutral conditions led to powders consisting of 2–10 nm diameter crystalline RuO₂ nanoparticles embedded in a matrix of crystalline (anatase) and amorphous TiO₂. Acid hydrolysis conditions gave gels containing smaller, amorphous RuO₂ nanoparticles (1–3 nm). In all samples the RuO₂ nanoparticles tended to clump into aggregates up to 0.5 μm across. Acid or neutral hydrolysis of ruthenium ethoxide gave samples which displayed lower surface Ru:Ti ratios as measured by XPS compared to the bulk (XRF), and also contained more low-valent Ru (as measured by XRF), probably due to incomplete hydrolysis of the precursors. These samples also contained more Ru metal after calcination (XRD). Calcination (450 °C) was accompanied by Ru-promoted combustion of organic material and led to crystalline (anatase) TiO₂ and Ti_xRu_1−xO₂ solid solution (rutile phase).     

Optical and electrical properties of p-type AgInSnxS2−x (x = 0–0.04) thin films prepared by spray pyrolysis

AgInSn_xS_2−x (x = 0–0.2) polycrystalline thin films were prepared by the spray pyrolysis technique. The samples were deposited on glass substrates at temperatures of 375 and 400 °C from alcoholic solutions comprising silver acetate, indium chloride, thiourea and tin chloride. All deposited films crystallized in the chalcopyrite structure of AgInS₂. A p-type conductivity was detected in the Sn-doped samples deposited at 375 °C, otherwise they are n-type. The optical properties of AgInSn_xS_2−x (x < 0.2) resemble those of chalcopyrite AgInS₂. Low-temperature PL measurements revealed that Sn occupying an S-site could be the responsible defect for the p-type conductivity observed in AgInSn_xS_2−x (x < 2) thin films.     

Effect of B-doping on the structural, magnetotransport and magnetocaloric properties of La0.67Ca0.33MnO3 compounds

In this study, the effect of Mn site substitution of B on the structural, electrical and magnetocaloric properties of manganites was investigated. Polycrystalline manganites with the chemical composition La_0.67Ca_0.33Mn_1−xB_xO₃ (x = 0, 0.1, 0.2 and 0.3) were prepared by the standard solid-state process. It was found that the magnetisation, the Curie temperature and the maximum value of the magnetic entropy change |ΔS_m| decrease with increasing concentration of B.     

Molecular beam epitaxial growth of SmBa2Cu3O7−δ thin films and effect of substrate temperature on the surface roughness

Stoichiometrically optimized, epitaxial SmBa₂Cu₃O_7-δ thin films with high T_{c, R = 0} and high critical current densities j_c have been prepared for the first time in a tightly controlled molecular beam epitaxy process in non-reactive molecular oxygen, followed by an in situ loading process with molecular oxygen. The surface roughness (on a submicrometre scale) of single-crystal films with their c axes perpendicular to the surface depends markedly on the surface temperature of the substrate during the deposition of the epitaxial films, within a range of only a few degrees centigrade. The calibrated optimal temperature for the preparation of epitaxial films 200 nm thick of this single orientation is found to be 680 ± 5 °C. In scanning tunnelling microscopy investigations, they show a surface roughness of less than 6 nm (five SmBa₂Cu₃O_7−δ unit cells) on a 2 μm × 2 μm scale. At deposition temperatures below this optimal deposition temperature, the well-known a-axis growth increases rapidly, whereas higher temperatures give a significantly higher surface roughness, which can be observed by scanning electron microscopy.     

Atomic layer deposition growth of zirconium doped In2O3 films

Zirconium doped indium oxide thin films were deposited by the atomic layer deposition technique at 500 °C using InCl₃, ZrCl₄ and water as precursors. The films were characterised by X-ray diffraction, energy dispersive X-ray analysis and by optical and electrical measurements. The films had polycrystalline In₂O₃ structure. High transparency and resistivity of 3.7×10⁻⁴ Ω cm were obtained.     

Synthesis and humidity sensitive properties of nanocrystalline Ba1−xSrxTiO3 thick films

Nanocrystalline Ba_1−xSr_xTiO₃ (x=0, 0.2, 0.4, 0.6, 0.8 and 1.0) precursors were synthesized using the stearic acid gel method. After the precursors had been calcined at 600–950°C for 0.5–1 h, nanocrystalline powders with the cubic perovskite structure were obtained and these were made into thick films. The powder samples were characterized by differential thermal analysis, X-ray diffraction and transmission electron microscopy, and the thick film samples were characterized by scanning electron microscopy and X-ray diffraction. The humidity-sensitive properties of the nanocrystalline Ba_1−xSr_xTiO₃ thick films were investigated. The results show that these nanocrystalline thick films possess higher humidity sensitivity and lower resistance than those of conventional materials.     

Microwave dielectric characteristics of Ba(Mg1/3Ta2/3)O3 ceramics sintered at low-temperatures

The microwave dielectric properties and microstructures of Ba(Mg_1/3Ta_2/3)O₃ (BMT) ceramics sintered at low temperatures with 2–3 wt.% NaF additives were investigated. BMT ceramics sintered at 1340 °C for 3–12 h showed dielectric constants (_r) of 25.5–25.7, Qf values of 41 500–50 400 GHz and temperature coefficients of the resonator frequency (τ_f) of 10.9–21.4 ppm °C⁻¹. The variation of sintering time almost had no effect on the dielectric constant. The Qf value increased and the τ_f decreased with increasing sintering time. The ordering degree of Mg²⁺ and Ta⁵⁺ at B-sites increased with increasing sintering time.