形貌转录法制备Ag-P(AM-co-MAA)复合微球

以反相悬浮聚合技术合成的丙烯酰胺(AM)和甲基丙烯酸(MAA)共聚高分子微凝胶P(AM-co-MAA)为模板,结合反胶束法制备得到Ag3PO4-P(AM-co-MAA)复合微球,并将其分散于乙醇溶剂中通过化学还原Ag3PO4-P(AM-co-MAA)复合微球制备得到粒径为几十微米,具有表面图案,且结构为核-壳型的Ag-P(AM-co-MAA)复合微球材料.能量散射X射线(EDX)谱表明壳化学组成以金属银为主,核以高分子模板为主;扫描电子显微镜(SEM)观察结果表明银-高分子复合微球的表面形貌与其前驱体类似,且可以通过选择模板、改变模板组成、调整金属难溶银盐沉积量等因素加以调控;X射线衍射(XRD)分析表明前驱体复合微球表面Ag3PO4全部转化为单质银.生物抗菌实验表明该类微球材料对大肠杆菌、金黄色葡萄球菌均具有较强的抑制作用.     

新颖表面结构的脲醛树脂-聚丙烯酰胺复合微球的制备研究

将高分子微凝胶模板法应用于制备脲醛树脂[Urea-formaldehyde resin (UF Resin)]-聚丙烯酰胺[Polyacrylamide (PAM)]有机-有机复合微球材料. 以PAM高分子微凝胶为模板, 通过控制甲醛和尿素的缩聚反应在反相悬浮体系中进行, 制备得到了具有新颖表面形貌的脲醛树脂-聚丙烯酰胺[UF Resin/PAM]有机-有机复合微球, 利用扫描电子显微镜(SEM)、热重分析(TGA)、红外(FT-IR)等手段对复合微球进行了表征. 实验结果表明, 复合微球的表面形貌与甲醛和尿素溶液的pH值、甲醛和尿素溶液的浓度、甲醛和尿素的摩尔比、模板的组成等因素有关. 可以预期, 本研究方法将为制备具有特异表面形貌的有机-有机复合微球材料提供了一条有效的途径.     

核-壳结构P(AM-co-MAA)-W-Ag复合微球的制备

以丙烯酰胺(acrylamide, AM)和甲基丙烯酸(methacrylic acid, MAA)的共聚微凝胶(P(AM-co-MAA))为模板, 通过离心沉积法将钨粉沉积于高分子微凝胶表面, 得到具有核-壳结构的P(AM-co-MAA)-W复合微球; 再以经聚乙烯基吡咯烷酮(PVP)修饰的P(AM-co-MAA)-W复合微球为模板, 在硝酸银溶液中充分溶胀后, 通过向反相悬浮体系中缓慢通入氨气, 制备得到了具有核-壳结构的P(AM-co-MAA)-W-Ag双金属复合微球材料. 实验发现, 通过改变制备过程中AgNO3的初始浓度和PVP的用量等条件, 可以改变复合微球表面银的沉积量; 并结合实验结果初步提出了银的形成机理, 即PVP的存在, 不仅可以作为稳定剂固定Ag+离子, 同时可以作为还原剂促进Ag+还原为Ag的反应.     

单分散P(St-BA-AN)/PANI核壳结构复合微球的制备与电性能

以苯乙烯(St)、丙烯酸丁酯(BA)和丙烯腈(AN)为单体, 采用乳液聚合的方法制备出单分散苯乙烯-丙烯酸丁酯-丙烯腈三元共聚物[P(St-BA-AN)]种子微球, 再在该种子微球表面包覆聚苯胺(PANI), 制得P(St-BA-AN)/PANI核壳结构复合微球. 采用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外透射光谱(FTIR)和漫反射光谱等测试手段对所制备的种子微球和复合微球的形态、结构和形成机理进行了研究, 并用四探针法测定了核壳结构复合物的导电性. 研究结果表明, 通过改变种子乳液共聚物的组成和加入苯胺的量及氧化剂的量等条件可调控复合微球的电导率. 与P(St-BA)/PANI核壳结构复合微球相比, 在核组成中引入了氰基的P(St-BA-AN)/PANI核壳结构复合微球的电导率明显提高, 当加入苯胺的量为P(St-BA-AN)种子微球与苯胺单体总质量分数的40%时, 其电导率可达到0.71 S/cm. 红外光谱结果证实了P(St-BA-AN)种子微球中的氰基和壳层中聚苯胺的胺基之间存在某种相互作用, 导致核壳结构复合物电导率的提高.     

反应介质pH值和前驱体用量对PSt/TiO_2复合微球结构形态及TiO_2空心微球形貌的影响

首先用聚乙烯亚胺(PEI)对粒径为360 nm的单分散无皂聚苯乙烯(PSt)乳胶粒进行修饰,得到表面荷正电的PSt种子乳液,然后将其滴加到溶有钛酸正丁酯(TBT)的乙醇与水的混合介质中,通过溶胶-凝胶(sol-gel)法制备出了核壳结构PSt/TiO2复合微球,系统研究了体系pH和TBT用量对复合微球结构形态的影响.研究表明,酸性条件不利于核壳结构PSt/TiO2复合微球的形成;当体系pH值为7.2时,可得到包覆完整、TiO2壳层厚度均一的PSt/TiO2复合微球,此后随着体系pH值的升高,包覆厚度逐渐提高;当pH值升高到11.0时,壳层厚度达到最大,但出现了包覆层不完整的复合微球.在固定聚合体系pH为8.5,EtOH/H2O质量比为100/6,表面修饰PSt种子乳液用量为0.5 g(固含量为4%)的条件下,随着TBT用量从0.01 g增加到0.16 g,复合微球壳层厚度从约0 nm逐渐增加到60 nm;当TBT用量增加到0.32 g时,壳层厚度迅速降至12nm,微球表面变得粗糙,并出现大量未包覆微粒;此后随着TBT用量的增加,包覆层厚度逐渐减少,未包覆微球逐渐增多.结果显示,当复合微球中TiO2包覆层达到一定厚度时,经煅烧后才能得到形貌完整的TiO2中空微球.     

制备方法对模板法制备SiO_2中空微球形貌的影响

模板法是制备无机中空微球的重要方法之一.首先通过苯乙烯和甲基丙烯酸的无皂乳液聚合法制得表面含羧基、粒径为360nm的单分散聚苯乙烯(PSt)乳胶粒,并以此为模板,分别采用表面改性-前驱体水解法(PHC)和SiO2纳米颗粒层层自组装法(LBL),制备出了不同壳层厚度的PSt/SiO2核壳结构复合微球,然后经500℃煅烧4h,得到SiO2中空微球.利用透射电镜和扫描电镜对微球结构形态进行了表征.研究表明,首先利用γ-氨丙基三乙氧基硅烷(KH-550)对PSt模板微球进行表面改性、然后再在乙醇-水混合介质中进行原硅酸乙酯(TEOS)水解与缩合反应的PHC法,是制备PSt/SiO2核壳结构复合微球的简便方法,复合微球经煅烧可制得表面均匀、结构致密、壳层厚度和形貌可控的SiO2中空微球;而LBL法制备PSt/SiO2核壳结构复合微球的工艺复杂,煅烧后所得SiO2中空微球结构疏松,易于破碎.     

原位合成的活性脲醛树脂作为模板剂制备二氧化硅介孔材料

利用酸性条件下正硅酸乙酯的水解和脲醛树脂的聚合反应同时一步原位进行的方法合成了二氧化硅复合粉体(包括核壳微球结构和网状结构)和块体凝胶材料. 液氮吸附BET分析结果证明复合材料焙烧后得到的二氧化硅孔径分布均匀, 大小在介孔范围内. 改变反应性单体尿素. 甲醛及正硅酸乙酯等的初始浓度可对二氧化硅块体材料的孔径大小进行调节. 扫描电子显微镜观测结果显示, 随着原料单体初始浓度的变化复合粉体材料的微米级形貌可以是多孔网状结构或核壳结构. 从红外光谱和差热分析的结果推测, 高甲醛/尿素摩尔比[n(甲醛)∶n(尿素)≥2]条件下形成的支链脲醛树脂可作为块体二氧化硅理想的孔结构导向剂.     

温敏性P(St-NIPAM)/PNIPAM-Ag复合微凝胶制备及性能研究

通过无皂乳液聚合和种子乳液聚合两步法合成苯乙烯与N-异丙基丙烯酰胺共聚物/聚N-异丙基丙烯酰胺[P(St-NIPAM)/PNIPAM]核-壳结构复合微凝胶, 再以其为模板在硝酸银水溶液中充分溶胀, 并以乙醇为还原剂, 在NH₃气氛条件下还原, 制备得到高分子微凝胶负载纳米银P(St-NIPAM)/PNIPAM-Ag的复合微凝胶材料. 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、傅里叶变换红外光谱仪(FT-IR)、X射线衍射仪(XRD)、热分析(TGA)、紫外-可见分光光度计(UV-vis)、激光粒度分析等手段对复合微凝胶进行结构、组成和性质表征. 研究结果表明, 复合纳米银后的P(St-NIPAM)/PNIPAM-Ag复合微凝胶仍具有温敏性, 且其温度敏感性随壳层中复合纳米银含量的增加而减弱. P(St-NIPAM)/PNIPAM-Ag复合微凝胶对对硝基苯酚的还原反应具有良好的催化活性, 在45 min内基本将对硝基苯酚催化还原为对氨基苯酚.     

N掺杂空心TiO2微球的合成与表征

采用无皂乳液聚合合成的聚苯乙烯(PS)微球为模板、氨水/三乙醇胺为催化体系, 通过溶胶-凝胶方法合成了PS/TiO₂(核/壳)复合微球, 然后通过煅烧制备了N掺杂、锐钛型空心TiO₂微球. 在反应体系中三乙醇胺扮演双重角色, 既是TiO₂生成及包覆过程的抑制剂又是空心TiO₂微球的N掺杂剂. 改变氨水、三乙醇胺和钛酸正丁酯用量可控制TiO₂壳的形态和尺寸. 氨水用量增加, PS/TiO₂复合微球的壳表面变得粗糙|三乙醇胺用量增加, 壳表面变得光滑|钛酸正丁酯用量提高导致壳层变厚. 改变三乙醇胺用量可调节空心TiO₂微球中的N掺杂量|N掺杂空心TiO₂微球具有可见光响应和光催化作用.     

石蜡基微胶囊相变材料研究进展北大核心CSCD

本文从微胶囊壁材出发,重点介绍了石蜡基/高分子、无机和高分子-无机杂化壳微胶囊的制备及应用,并总结了上述微胶囊的优势和不足。其中石蜡基/高分子壳微胶囊的壁材包括三聚氰胺-甲醛树脂、脲醛树脂、三聚氰胺-甲醛-尿素树脂、聚氨酯树脂、丙烯酸树脂等,石蜡基/无机壳微胶囊的壁材包括二氧化硅、二氧化钛、碳酸钙、氧化锌等,石蜡基/高分子-无机杂化壳的壁材包括三聚氰胺-甲醛树脂、三聚氰胺-甲醛-尿素树脂、丙烯酸树脂等与二氧化钛、二氧化硅等无机粒子复合。并对石蜡基微胶囊相变材料的未来发展方向和应用前景进行展望,以期为今后研究提供借鉴。     

Controllable synthesis of CuS-P(AM-co-MAA) composite microspheres with patterned surface structures

Copper sulfide-poly(acrylamide-co-methacrylic acid) (CuS-P(AM-co-MAA)) composite microspheres with patterned surface structures have been synthesized in a controllable manner by means of the polymer microgel template method. The formation of CuS particles can be regulated by controlling the decomposition of thioacetamide (TAA) in acidic solution. Compared with the microgel template, the surface morphologies of the composite microspheres are characterized by compact and creased textures. The surface morphology of the composite microspheres has been found to be mainly influenced by the amount of copper sulfide precipitated and hence by the rate of H(2)S gas generation. This study might provide a potential route for controlling the synthesis of various metal sulfide-polymer composites with patterned surface structures.     

Adsorption of poly(N-isopropylacrylamide-co-4-vinylpyridine) onto core-shell poly(styrene-co-methylacrylic acid) microspheres

Adsorption of the thermoresponsive copolymer of poly(N-isopropylacrylamide-co-4-vinylpyridine) (PNIPAM-co-P4VP) onto the core-shell microspheres of poly(styrene-co-methylacrylic acid) (PS-co-PMAA) is studied. The core-shell PS-co-PMAA microspheres are synthesized by one-stage soap-free polymerization in water. The copolymer of PNIPAM-co-P4VP is synthesized by free radical polymerization of N-isopropylacrylamide and 4-vinylpyridine in the mixture of DMF and water using K₂S₂O₈ as initiator. Adsorption of PNIPAM-co-P4VP onto the core-shell PS-co-PMAA microspheres results in formation of the composite microspheres of PS/PMAA-P4VP/PNIPAM. The driven force to adsorb the copolymer of P4VP-co-PNIPAM onto the core-shell PS-co-PMAA microspheres is ascribed to hydrogen-bonding and electrostatic affinity between the P4VP and PMAA segments. The resultant composite microspheres of PS/PMAA-P4VP/PNIPAM with surface chains of PNIPAM are thermoresponsive in water and show a cloud-point temperature at about 33 °C.     

PMAA microgel surface-supported phase transfer catalyst as reusable microreactors for ultra-deep desulfurization

The reusable microreactors, poly(methacrylic acid) (PMAA) microgels surfacely covered with 3-(trimethoxysilyl)-propyldimethyloctadecyl ammonium chloride (AEM) and K₂{W(=O)(O₂)₂(H₂O)}₂ (W2) complexes, have been synthesized by using an ion exchange reaction between AEM located on PMAA microgels and W2 in aqueous solution. The final composite microspheres and intermediate products are characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, energy dispersive X-ray spectrophotometer, and thermogravimetric analysis, respectively. The results indicated the PMAA/AEM/W2 composite microspheres with surface-wrinkling morphology and core-shell structure. The feasibility of the composite microspheres used as reusable microreactors in catalytic oxidation of dibenzothiophene (DBT) was investigated. Additionally, the effects of some factors, including the amount of the microreactors, temperature, H₂O₂/DBT molar ratio, the loaded amount of AEM, DBT concentration, and recycling times, on the catalytic oxidation were examined. The results demonstrated that the prepared composite microspheres possess high catalytic performance and reusability in the catalytic oxidation of DBT.     

Effects of reaction temperature and reaction time on positive thermosensitivity of microspheres with poly(acrylamide)/poly(acrylic acid) IPN shells

We have successfully prepared monodispersed positively thermoresponsive core-shell hydrogel microspheres with poly(acrylamide-co-styrene) [P(AAM-co-St)] cores and IPN(interpenetrating polymer network)-based shells composed of poly(acrylamide)/poly(acrylic acid). The submicron-sized monodispersed P(AAM-co-St) core seeds were prepared by using a surfactant-free emulsion polymerization method, and the IPN-based shell layers were fabricated onto the core seeds by using a method of sequential IPN synthesis. Effects of reaction time and reaction temperature during preparation of IPN on the particle size, monodispersity, and thermoresponsive characteristics of microspheres were investigated. The results show that the sizes of particles with IPN shell layer are smaller than that of seeds, and the change of monodispersity among them is not obvious and the monodispersity of particles prepared under higher reaction temperature is higher than that of seeds and those particles prepared under lower reaction temperature. With increasing reaction time, thermoresponsive characteristics of microspheres increases. While thermoresponsive characteristics of microspheres decreases sharply with increasing reaction temperature. The results display preparation of IPN-structured microspheres is so careful to need longer reaction time and lower reaction temperature.     

Facile synthesis of hollow polymer microspheres with movable cores with the aid of hydrogen-bonding interaction

Poly(divinylbenzene-co-acrylic acid) (poly(DVB-co-AA)) hollow microspheres with movable poly(DVB-co-AA) cores were prepared by a facile route. In this approach, poly(DVB-co-AA) microspheres were first used as templates to synthesize poly(DVB-co-AA)@PAA core-shell particles with a non-crosslinked PAA shell by distillation precipitation polymerization in acetonitrile. In situ polymerization to prepare poly(DVB-co-AA)@PAA@poly(DVB-co-AA) trilayer microspheres was then developed, in which the hydrogen-bonding interaction between the carboxylic acid groups played a key role as the driving force for the formation of monodisperse trilayer structure polymer microspheres. After removal of the non-crosslinked poly(acrylic acid) (PAA) midlayer of the poly(DVB-co-AA)@PAA@poly(DVB-co-AA) microspheres in ethanol under basic conditions, poly(DVB-co-AA) hollow microspheres with movable poly(DVB-co-AA) cores were obtained. Functional poly(DVB-co-AA) cores could be released successfully when the hollow structure was destroyed. The resultant core-shell, trilayer polymer microspheres and hollow polymer microspheres with movable cores were characterized by transmission electron microscopy (TEM), dynamic laser scattering (DLS), and Fourier transform infrared (FT-IR) spectra.     

SYNTHESIS OF POLY(DIVINYLBENZENE-co-ACRYLIC ACID) HOLLOW MICROSPHERES WITH GOLD NANOPARTICLES ON THE INTERIOR SURFACE

Poly(divinylbenzene-co-acrylic acid) (poly(DVB-co-AA)) hollow microspheres with gold nanoparticles on the interior surfaces were prepared from the gold nanoparticles-coated poly(methacrylic acid) (PMAA@Au@poly(DVB-co-AA)) core-shell microspheres by removal of the PMAA core in water.Au nanoparticles-coated PMAA microspheres were afforded by the in-situ reduction of gold trichloride with PMAA microsphere as stabilizer via the interaction between carboxylic acid groups and Au nanoparticles.Gold nanoparticle...     

Reparation of silica/poly(methacrylic acid)/poly(divinylbenzene-co-methacrylic acid) tri-layer microspheres and the corresponding hollow polymer microspheres with movable silica core

 Hollow poly(divinylbenzene-co-methacrylic acid) (P(DVB-co-MAA)) microspheres were prepared by the selective dissolution of the non-crosslinked poly(methacrylic acid) (PMAA) mid-layer in ethanol from the corresponding silica/PMAA/P(DVB-co-MAA) tri-layer hybrid microspheres, which were afforded by a three-stage reaction. Silica/PMAA core-shell hybrid microspheres were prepared by the second-stage distillation polymerization of methacrylic acid (MAA) via the capture of the oligomers and monomers with the aid of the vinyl groups on the surface of 3-(methacryloxy)propyl trimethoxysilane (MPS)-modified silica core, which was prepared by the Stöber hydrolysis as the first stage reaction. The tri-layer hybrid microspheres were synthesized by the third-stage distillation precipitation copolymerization of functional MAA monomer and divinylbenzene (DVB) crosslinker in presence of silica/PMAA particles as seeds, in which the efficient hydrogen-bonding interaction between the carboxylic acid groups played as a driving force for the construction of monodisperse hybrid microspheres with tri-layer structure. The morphology and the structure of silica core, silica/PMAA core-shell particles, the tri-layer hybrid microspheres and the corresponding hollow polymer microspheres with movable silica cores were characterized by transmission electron microscopy (TEM), Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy (XPS).