脲醛树脂合成反应过程的FTIR研究

利用傅里叶变换红外(FTIR)光谱研究了脲醛树脂合成中不同结构形成和变化情况. 对FTIR谱图解析和分析的结果表明, 在脲醛树脂预聚物合成过程中, 随着甲醛与尿素反应的进行, 红外谱图特征峰发生有规律的变化, 酰胺II带特征峰波数逐渐低移, 有更多羟甲基、醚键和—NHCH2—结构基元形成, 固化反应使上述结构基元相应减少. 着重分析了不同甲醛与尿素摩尔比(nF/nU)下尿素与甲醛反应产物结构的变化, 随nF/nU的增加, 酰胺II带特征峰波数逐渐低移, 碱性条件下醚键和—NHCH2—结构基元明显增加, 在较强酸性条件下Uron环、亚甲基桥和羟甲基显著增加, 而—NHCH2—结构基元含量下降.     

有机硅改性丙烯酸酯共聚乳液合成方法及胶膜性能的研究

用一次投料法、单体乳液滴加法和引发剂滴加法有机硅改性丙烯酸酯共聚乳液，聚合过程、胶粒形态及乳液稳定性的观测结果表明：单体乳液滴加法是合成该类乳液的最佳方法，研究了单体乳液滴加法中有机硅含量与聚合反及胶膜性能的关系，结果表明：有机硅含量在１５％以下时，聚合反应可以顺利进行，胶膜性能不仅依赖于聚合时有机硅单体的总量，而且还依赖于有机硅单体中活性硅氧烷所占的比例。     

Preparation of sulphonate-containing polymer particles <Emphasis Type="Italic">via</Emphasis> semi-continuous emulsion copolymerizaion of styrene and sodium styrene sulphonate

Submicron-sized P(St-NaSS) latexes were prepared via a semi-continuous emulsion copolymerization of styrene (St) and sodium styrene sulphonate(NaSS) in the presence of anionic surfactant,in which NaSS aqueous solution and St were separately dropwise charged into the polymerization system at the same time.The hydrodynamic diameter of the latex particles was measured by dynamic light scattering(DSL) method,and the NaSS unit content of the purified copolymer by water extraction was calculated based on the elementary analysis.Results showed that the copolymerization could be performed smoothly with the monomer conversion more than 96%in the absence of crosslinker,and PNaSS homopolymer could be removed from the latex product by water extraction for 28 h.The weight loss in the water extraction tended to decrease and the NaSS unit content of the purified copolymer tended to increase with the increase of monomer feeding time, and both of them increased with the increase of NaSS/St mole ratio in the charge.The introduction of divinyl benzene (DVB) could decrease the weight loss in the water extraction and increase the NaSS unit content of the purified copolymer. When 25/75 mole ratio of NaSS/St and 11 mol%DVB of total NaSS and St were used in the recipe,and the monomer feeding time was 3 h in copolymerization,the NaSS unit content of the purified copolymer reached 7.31 mol%.     

pH值和前驱体用量对核壳结构PSt/SiO2复合微球结构形态的影响

首先通过无皂乳液聚合法制得表面含羧基、粒径为360 nm的单分散聚苯乙烯(PSt)种子乳液,并在EtOH/H2O混合介质中用γ-氨丙基三乙氧基硅烷(KH-550)对其进行改性,制得表面含有活性硅乙氧基并带有正电荷的改性PSt乳胶粒,然后再加入原硅酸乙酯(TEOS)进行共水解与共缩聚反应,制备出了核壳结构PSt/SiO2...     

萘酰亚胺类荧光染料及共聚型荧光聚氨酯乳液的合成与性能

首先以4-溴-1,8-萘酐、2-氨基-1,3-丙二醇和甲醇钠为原料, 经亚胺化和取代两步反应合成出4-甲氧基-N-(2-羟基-1-羟甲基乙基)-1, 8-萘酰亚胺(MHHNA)活性荧光染料, 然后将其作为扩链剂通过相反转自乳化法制备出了共聚型荧光聚氨酯(PU) (PU-MHHNA)乳液, 并分别采用核磁共振氢谱(¹H NMR)、核磁共振碳谱(¹³CNMR)、元素分析、傅里叶变换红外(FTIR)光谱、紫外-可见(UV-Vis)吸收光谱、荧光光谱、粒度分析、氙灯老化等方法对所得荧光染料的化学结构、PU乳液及乳胶膜的性能进行了表征. 结果表明, MHHNA和PU-MHHNA的荧光量子产率分别为0.73 和0.92, MHHNA的用量对所得PU乳液的胶体性质没有明显影响. PU-MHHNA的丙酮溶液在UV-Vis 吸收光谱上的最大吸收波长(λ_max)为360.6 nm, 在荧光光谱上的最大激发波长(λ_ex)和最大发射波长(λ_em)分别为362和435 nm. 随着温度的升高, PU-MHHNA的荧光强度逐渐降低. PU-MHHNA乳胶膜的耐光色牢度和耐溶剂色牢度均明显高于共混型荧光聚氨酯(PU/MBNA)乳胶膜.     

种子乳胶粒表面修饰法制备核壳结构PSt/TiO_2复合微球

首先采用无皂乳液聚合法合成了表面带负电荷、粒径为360 nm的单分散聚苯乙烯(PSt)乳液,并利用聚乙烯亚胺(PEI)在25℃下对PSt乳胶粒表面进行修饰,得到了表面带有正电荷的PSt种子乳液;然后以乙醇和水的混合物为反应介质,采用种子乳液加入法,使钛酸正丁酯(TBT)在修饰后的乳胶粒表面进行水解与缩合,制备出了核壳结构PSt/TiO2复合微球,利用电镜对复合微球的结构形态进行了表征.结果表明,PSt乳液改性时体系的zeta电位随着PEI用量的增加而升高,当PEI用量为PSt聚合物重量的15%时,体系的zeta电位从原来的-40.3 mV升高到了38.3 mV,达到对PSt乳胶粒表面改性的最佳值;在制备PSt/TiO2复合微球时,TiO2包覆量随着反应时间的延长而增加,反应7 h时达到90.2%的最大值;随介质中水含量的增加,吸附到复合微球表面上的TiO2纳米颗粒逐渐减少,复合微球表面逐渐变得光滑,当EtOH/H2O质量比为100/6.0时,得到结构均一、壳层厚度为29 nm的核壳结构PSt/TiO2复合微球.     

新型可聚合蒽醌染料单体及其共聚物乳液的制备及性能

通过多步有机反应合成了新型蒽醌染料单体1-(间(2-(2-(丙烯酰氧基)乙氧基)乙基砜基)苯胺基)蒽醌(AVSAQ),对其化学结构进行了表征;然后将其与苯乙烯(St)、丙烯酸丁酯(BA)和甲基丙烯酸(MAA)进行半连续乳液共聚合,制备出了共价键合型P(St-BA-MAA-AVSAQ)橙红色聚合物乳液,并对乳液以及乳胶膜的性能进行了表征,系统考察了AVSAQ和过硫酸铵(APS)用量对单体总转化率以及乳液胶体性质的影响.结果表明,当AVSAQ用量不高于单体总量的4.0 wt%、APS用量不低于单体总量的0.5 wt%时,聚合反应可以平稳进行,所得乳胶粒水合粒径均在60 nm左右.总单体转化率和AVSAQ转化率随着AVSAQ用量的增加而降低,当AVSAQ用量达到4.0 wt%时,二者分别为95.0%和93.6%.P(St-BA-MAA-AVSAQ)的UV-Vis吸收光谱特性与AVSAQ完全一致,最大吸收波长均为486.8 nm.与相应非共价键合型橙红色聚合物乳液相比,P(StBA-MAA-AVSAQ)聚合物乳液具有良好的储存稳定性和保色性,乳胶膜的光色牢度和耐溶剂牢度也显著提高.     

Effect of the Shell Crosslinking Level andCore/Shell Ratio on the Morphology of LatexParticles in the Preparation of Hollow Latexes简

Three-layer core/shell latex particles with various shell crosslinking level and shell thickness were prepared by multistep emulsion polymerization, and the hollow latex particles with different morphologies were then obtained after alkali post-treatment. Influences of divinyl benzene(DVB) content and the core/shell mass ratio on emulsion polymerization and particle morphology were investigated. Results showed that with the increase of DVB content, the percentage of total amount of ―COOH on the particle surface and free in aqueous phase(PSFa) decreased, and the morphology of the post-treated particles underwent evolution from cracked, intact hollow to deficient swelling structure. Decreasing the core/shell mass ratio could not only make more carboxyl groups encapsulated by the shell, but also increase the shell resistance to the swelling of the core. The uniform hollow latex particles with intact morphology were obtained when the DVB content was 3.54 wt% and the core/shell mass ratio was 1/6.     

Investigation of cationic soapless P(St-<Emphasis Type="Italic">co</Emphasis>-DMAEMA) latex and its electrostatic adsorption of laponite

Cationic poly(styrene-co-N,N-dimethylaminoethyl methacrylate) (P(St-co-DMAEMA)) latexes were prepared in the absence of surfactant by using 2,2’ -azobis (2-methylpropionamidine) dihydrochloride (AIBA) as the initiator. The effects of the AIBA concentration, HCl/DMAEMA molar ratio and DMAEMA amount on the emulsion polymerization and the latex properties were investigated. The particle morphology and size, the zeta potential and the amino distribution of the P(St-co-DMAEMA) latexes were characterized by transmission electron microscope (TEM), dynamic light scattering (DLS) and conductometric titration, respectively. Results showed that the emulsion polymerization performed smoothly with high monomer conversion and narrow particle size distribution under the optimized conditions with AIBA concentration of 1 wt%, HCl/DMAEMA molar ratio of 1.2 and DMAEMA content of 5 wt%. The diameter of the dried latex particles decreased and the density of amino groups on the particle surfaces increased with increasing the DMAEMA content. The zeta potential of the P(St-co-DMAEMA) latexes was pH-dependent and the zero point was around at pH 7.2. A facile method was developed to fabricate P(St-co-DMAEMA)/laponite hybrid nanoparticles via electrostatic adsorption, in which the loading capacity of laponite platelets reached 17.7 wt%, and the resultant hybrid nanoparticles showed good thermal stability.     

单组分室温交联聚合物乳液研究进展

水性聚合物产品具有环境友好、成本低、节约资源和能源等优点,因而油漆、涂料、粘合剂等重要化学品的水性化是社会发展的必然需求.而聚合物乳液作为水性聚合物产品的成膜物,其适当的交联是提高产品性能的重要途径之一.本文对不同交联机理的单组分室温交联水性聚合物乳液进行了综述,着重介绍了该领域的一些重要交联体系和进展情况.