单晶LaB6热阴极直流发射特性实验研究

 实验利用二极管型电子枪研究了单晶LaB₆热阴极的直流发射特性。阴阳极间距5 mm,从直径为2 mm发射体上测得175 mA直流束流（阴极温度约为1 870 K、阴阳极电压6.5 kV、空间电荷限制状态）,电流密度为5.57 A/cm2。采用Longo方程拟合直流发射电流,该方法比以往单纯用Child或Richardson- Dushman公式更符合实际。实验还观测了阴极工作环境和表面状态对直流发射的影响,当真空度低于7×10^-4 Pa时,阴极发射能力逐渐下降,阴极表面碳、氧污染使发射体功函数升高。长时间加热后,石墨上会蒸镀LaB6,由此会造成热子电阻的下降。分析表明La原子补充不及时和表面气体吸附是影响直流发射能力的主要因素。     

铁电阴极制备与性能实验研究

 讨论了不同发射机理对铁电阴极材料性能的要求,对PZT（锆钛酸铅）系铁电陶瓷工艺过程中的关键步骤进行了研究。通过掺杂改性和改进预烧条件等手段,有效地改善了材料的性能参数,制备出相对介电常数大于3 000的弛豫相铁电陶瓷和压电常数大于500×10^-12C/N的铁电相铁电陶瓷。在初步的发射实验中,使用改进工艺后的PLZT8/65/35制备的铁电阴极,触发脉冲5.4 kV时,获得的发射电子电流密度达到800 A/cm^{2/sup>,远大于C-L定律计算的发射电流。}     

大直径钪酸盐阴极发射特性

 为获得kA级热发射电子束,研制了直径为100 mm钪酸盐热阴极组件,并建立了适应大面积热阴极实验环境的2 MV 注入器试验平台。实验在二极管真空3.7×10^-5 Pa、二极管电压1.95 MV、脉宽120 ns（FWHM）、阴极温度1 120 ℃时,获得最大收集电流1 038 A,发射电流密度约13 A/cm²。实验结果表明,工作状态下阴极发射能力与激活温度、系统真空度关系密切。     

强流四脉冲电子束源实验研究

 为了进行强流多电子束源研究，对现有2MeV LIA 注入器进行了四脉冲改造，二极管脉冲电压约500kV。实验研究了天鹅绒阴极在四脉冲条件下的发射能力、传导电流负载效应以及阴极等离子体运动对阴极电子发射和束能量的影响。利用空间电荷限制流模型推算出阴极等离子体膨胀速率在1 ~4cm/μs之间。     

Electron emission characteristics of the porous polycrystalline silicon diode

It is estimated that a porous polysilicon (PPS) diode with a structure of Au/PPS/n-type Si operates as an efficient stable surface emitting cold cathode. 2.0 μm of an non-doped polysilicon layer is formed on an heavily doped n-type silicon wafer and anodized in a solution of HF (50%):ethanol=1:1 under illumination by a 500 W tungsten lamp from a distance of 20 cm. The electron emission properties of the PPS diode were investigated as a function of anodizing condition such as anodizing current density. The electron emission trajectory was investigated, and it was also demonstrated their good uniformity in the emitting area.     

无铅铁电陶瓷电子发射性能

 铁电阴极材料，作为一种新型的功能材料，以其高的发射电流密度等优点而受到重视。鉴于目前研究的铁电阴极材料多局限于锆钛酸铅等含铅材料，作者采用无铅铁电陶瓷Na₁/2Bi_1/2TiO₃-BaTiO₃(BNBT)，进行了电子发射实验，获得发射电流密度达20A/cm²。初步实验结果表明，与锆钛酸铅相比，钛酸铋钠发射电流密度略低但性能稳定性较好。作为无铅铁电阴极，BNBT仍然具有良好的研究开发价值。     

Onset of breakdown and formation of cathode spots

When an increasing diode voltage is applied, enhanced field emission of electrons begins from a growing number of small spots or whiskers on the cathode surface. This stimulates desorption of weakly bound adsorbates from the surface of a whisker. As the diode voltage increases, the 100-V equipotential surface moving toward the cathode is met by the desorbed neutrals moving away from the cathode, resulting in sharp risetime for the onset of ionization of desorbed neutrals by field-emitted electrons. Positive ions produced in the ionization region a few microns from the electron emitting spot are accelerated back to it. This bombardment leads to surface heating of the spot. The onset of breakdown by this mechanism requires much less current than the Joule heating mechanism. The localized buildup of plasma above the electron emitting spot leads to pressure and electric field distributions that ignite unipolar arcs. The high current density of the unipolar arc and the associated surface heating by ions result in the explosive formation of cathode spot plasma     

二极管爆炸发射阴极等离子体的膨胀扩展

分析了二极管中爆炸发射产生阴极等离子体的演化特征,在考虑了阴极等离子体朝阳极膨胀运动使二极管阴阳极间距缩短这一效应的同时,还计入了阴极等离子体沿发射表面径向扩展运动对二极管有效发射面积的影响。基于Child-Langmuir定律,利用在一个四脉冲强流电子束源装置上得到的电流、电压等实验数据,假定阴极等离子体轴向膨胀和径向扩展速度近似相等,研究了阴极等离子体的膨胀扩展动力学行为。计算结果表明,阴极等离子体朝阳极的膨胀和沿径向的扩展速度为0.9～2.8 cm/s。     

GaAlAs快速边发光管发射端面沉积Al2O3抗反射层的研究

本文报导了在快速DH GsAs-GaAlAs边发光管发射端面上溅射沉积Al2O3抗反射层的研究,涂层厚度与输出光功率的提高密切相关,层厚接近λ/4值时,在200mA下光功率输出的提高达~80%.     

稳定的蓝色及白色有机薄膜电致发光器件

报道了一种稳定的蓝色和白色有机薄膜电致发光器件,蓝色器件最大亮度为7526cd／m^2,最大效率1．451m／W,半亮度寿命1035h(初始亮度l00cd／m^2)。白色器件的最大亮度为14850cd／m^2,最大效率2．881m／W,色度x=0．31,y=0．38,且色度不随电流增大而变化,半亮度寿命为2860h(初始亮度100cd／m^2)。     

电化学刻蚀法制备LaB6场发射微尖锥阵列

采用电化学刻蚀方法,成功制备出单尖的六硼化镧、钼、钨及钨铼合金场发射冷阴极尖锥,并对这几种场发射单尖锥阴极的电子发射性能进行了测试比较.结果表明,LaB₆作为场发射阴极,具有良好的发射性能和稳定性.在〈111〉面单晶LaB₆基片上,用PECVD法沉积非晶硅作掩膜,制备出具有一定高度的LaB₆微尖锥场发射阵列,结果发现,LaB₆基底较为平整,尖锥阵列呈现出各向异性.该结论对LaB₆材料在场发射阴极方面的进一步研究具有重要的指导意义.     

CSRm束流径向和轴向振荡的耦合

介绍了由于磁铁的安装误差和螺线管的存在而造成的束流径向和轴向的耦合，以及耦合对束流稳定的影响。结合CSRm结构的典型参数分析得出:二极磁铁和四极磁铁在纵向角安装偏差为-0.5~0.5 mrad；有螺线管存在的情况下，工作点落在和共振线时，将导致束流不稳定而大量损失，落在差共振线时，束流稳定。通过模拟计算发现:螺线管产生的耦合远大于磁铁的纵向角安装偏差产生的耦合。     

低阻抗大面积二极管的研制

采用高纯石墨环状阴极和有机玻璃绝缘子,研制了一套低阻抗大面积二极管系统。使用理论计算和数值模拟方法对二极管进行优化设计,在保证绝缘要求的同时,尽量优化二极管轴向长度和内外筒距离以减小二极管的回路电感。实验结果表明,优化后的二极管能在200 kV左右的电压上稳定工作,绝缘结构未发生击穿现象;实验中最高输出电压为213 kV,电流为221 kA,特性阻抗约为1 ,电流密度为8 kA/cm2,脉宽(FWHM)为50 ns。     

多晶LaB6阴极的脉冲热发射特性

 采用多晶LaB₆材料制成平板二极管阴极，阳极采用钼材料，阴极采用热传导与热辐射加热，加热体为石墨。实验研究了不同阴极温度、不同真空度下的脉冲发射特性，并对热发射稳定性进行了分析。结果表明： 在动态真空系统中， 阴极发射面积为0.012 1 cm²， 工作真空度为2×10^-4 Pa， 阴极温度分别为1 600， 1 650和1 700 ℃，在脉冲宽度为40 ms、重复频率为107 Hz的条件下，最大脉冲发射电流密度分别为34.0，44.0和53.8 A/cm²; 2×10^-4，5×10^-4和2×10^-3 Pa压强下的发射能力没有明显的差异;脉冲宽度的变化不影响发射电流密度的变化。     

碳纳米管阴极强流脉冲发射特性实验

 在2 MeV直线感应加速器注入器平台上研究了采用浸渍涂覆方法制备的大面积碳纳米管阴极发射体的强流发射特性。研究结果表明：在脉冲高压电场下,碳纳米管阴极具有强流电子束发射能力,发射电流密度较大;碳纳米管阴极发射电子过程为场致等离子体发射。实验过程中,阴极端取样电阻环收集到的最大发射电流达350 A,阳极端法拉第筒收集的发射电流为167 A,最大阴极发射电流密度为19.4 A/cm²。     

常见场致发射阴极材料的发射特性

利用三阴极加速器平台,对不锈钢、黄铜、铝、天鹅绒和石墨等几种常见场致发射材料的电流发射能力、相对启动延迟时间及其抖动进行了实验研究。实验结果表明:在二极管电压近似恒定时,不锈钢阴极启动时间延迟抖动小于8 ns,天鹅绒阴极及石墨阴极启动时间延迟抖动小于4 ns;且材料在阴极频繁工作时启动时间加快;常见金属材料中不锈钢阴极的综合性能较好;非金属材料中,天鹅绒阴极的发射能力最强,且发射延迟时间最短,但考虑到天鹅绒材料严重的出气问题,非金属材料中以石墨阴极的性能为优。     

碳纳米管/金刚石复合材料的场发射特性

采用微波烧结方法制备了碳纳米管/金刚石复合材料。将碳纳米管和纳米金刚石粉末混合后研磨压片,然后在微波等离子气相沉积系统中采用微波烧结。利用扫描电镜对复合材料的表面形貌和微观结构进行了分析,结果显示碳纳米管比较均匀地分散于复合材料中,并在表面形成了发射微尖。利用二极管结构在动态真空室中对复合材料的场发射特性进行了研究,复合材料有较好的场发射特性,电流密度接近15mA/cm2。     

Generation and transport of high-current, low-energy electron beams in a system with a gas-filled diode

Investigations of the generation and transport of a high-current, low-energy electron beam are performed in a system with a gas-filled diode based on a plasma cathode. At accelerating voltages of up to 20 kV and pressures of (1–5)×10⁻¹ Pa, a beam with an emission current of 600 A, emission current density of 12 A/cm² and pulse duration of 30 μs if obtained in a diode with a grid-stabilized emission opening having a diameter equal to 8 cm. The beam is transported in the absence of an external magnetic field over a distance of 20 cm. The beam is compressed by its self-magnetic field, and the current density at the collector reaches 100 A/cm² when the beam diameter is 3 cm. Zh. Tekh. Fiz. 68, 44–48 (January 1998)     

太赫兹源场致发射电子源

通过粒子模拟(PIC)软件模拟计算了在ps级别下二极与三极结构碳纳米管场致发射的电流密度与电子注聚焦性能。阳极电压在2 kV时,二极结构下电流密度达到1.85 A/cm2;三极结构下,栅压700 V时发射电流密度达到2.3 A/cm2,且在一定的三极结构参数与电极电压下,可以获得较好的电子注聚束效果。通过碳纳米管二极管发射实验,获得了6.6 A/cm2的发射电流密度,总发射电流达到52.1 mA,可以为太赫兹器件提供连续发射的电子注。     

Study of Intense Electron Beams Produced by High-Voltage Pulsed Glow Discharges

We report the generation of high-current-density (20 A/cm2) pulsed electron beams from high-voltage (48-100 kV) glow discharges using cathodes 7.5 cm in diameter. The pulse duration was determined by the energy of the pulse generator and varied between 0.2 ?s and several microseconds, depending on the discharge current. The largest electron beam current (900 A) was obtained with an oxidized aluminum cathode in a helium-oxygen atmosphere. An oxidized magnesium cathode produced similar results, and a molybdenum cathode operated at considerably lower currents. A small-diameter (<1 mm) well-collimated beam of energetic electrons of very high current density (>1 kA/cm2) was also observed to develop in the center of the discharge. Electrostatic probe measurements show that the negative glow plasma density and the electron beam current have a similar spatial distribution. Electron temperatures of 1-1.5 eV were measured at 7 cm from the cathode. The plasma density (8.5 · 1011 cm-3 at 450 A) was found to depend linearly on the discharge current. In discharges at high currents a denser and higher temperature plasma region was observed to develop at approximately 20 cm from the cathode. We have modeled the process of electron beam generation and predicted the energy distribution of the electron beam. More than 95 percent of the electron beam energy is calculated to be within 10 percent of that corresponding to the discharge voltage.