碳纳米管阴极的强流脉冲发射性能研究

采用丝网印刷和涂敷方法制备了两种碳纳米管阴极，并研究了两种阴极的强流脉冲发射特性，表征了阴极表面碳纳米管的形貌及分布.研究结果表明在脉冲宽度为100 ns、电压为1.64×10⁶ V的脉冲电场下，涂敷法制备阴极的场发射电流最高达5.11 kA，最高发射电流密度达260 A/cm².丝网印刷法制备阴极的场发射稳定性优于涂敷法制备阴极，但其发射电流低.阴极表面发射体的形貌与分布影响了阴极的脉冲发射性能.碳纳米管阴极的脉冲发射机理为爆炸电子发射.碳纳米管阴极可以作为强 关键词： 碳纳米管 阴极 脉冲发射 强电流     

改性剂对旋转法SiO2减反膜均匀性的影响

 分析了采用旋转涂膜法制备溶胶-凝胶SiO₂减反膜过程中条纹缺陷产生的机理,利用含氟醇类试剂对减反膜溶胶进行改性,使溶胶链段柔顺性及流动性得到改善。在光学显微镜下对改性前后的膜层进行了对比和分析,对膜层的表面形貌、表面粗糙度以及透射比等特性进行了表征。结果表明:溶胶改性之后的膜层未出现条纹缺陷,表面粗糙度均方根值从4.55 nm下降到小于1.00 nm,膜层表面质量有了较大提高;改性前后膜层的增透性能相当,在熔石英基片上制备的膜层峰值透射比为99.60%~99.89%,膜层激光损伤阈值为21.0~25.3 J/cm²。     

亚微米电子发射材料的合成及发射性能

介绍一种气-液相合成技术合成多元碳酸盐及其制备阴极的发射性能.实验表明：采用该方法合成碳酸盐结晶小,形貌呈细丝状,丝径小于1μm,这种亚微米丝状碳酸盐能明显提高氧化物阴极的发射性能.通过对阴极激活后阴极表面的SEM分析,初步讨论了亚微米碳酸盐的发射机理. 关键词： 亚微米碳酸盐 气-液相合成技术 氧化物阴极 发射性能     

三代微光像增强器制管工艺对阴极光电发射性能的影响

主要论述制管工艺对光电阴极发射性能的影响。通过分析仪器和光学检测方法对管子阴极制备的台内及台外工艺质量进行了在线追踪和监测．结果表明，影响台外工艺质量的主要因素是外延材料缺陷多、发射层表面氧化、杂质污染、掺杂浓度不均匀、掺杂浓度陡度变化小及GaAs与玻璃粘接产生的应力大；影响台内工艺质量的主要因素为阴极激活真空度低于8×10^-8Pa．真空残气H2O．CO．CO2及C分压大于10^-8Pa．阴极激活铯和氧源提纯不彻底。利用透反射光照法激活台内对组件表面测线．发现发射层表面针孔、裂纹和发雾是造成阴极发射性能低的关键因素。     

铁电阴极制备与性能实验研究

 讨论了不同发射机理对铁电阴极材料性能的要求,对PZT（锆钛酸铅）系铁电陶瓷工艺过程中的关键步骤进行了研究。通过掺杂改性和改进预烧条件等手段,有效地改善了材料的性能参数,制备出相对介电常数大于3 000的弛豫相铁电陶瓷和压电常数大于500×10^-12C/N的铁电相铁电陶瓷。在初步的发射实验中,使用改进工艺后的PLZT8/65/35制备的铁电阴极,触发脉冲5.4 kV时,获得的发射电子电流密度达到800 A/cm^{2/sup>,远大于C-L定律计算的发射电流。}     

深紫外激光光发射与热发射电子显微镜在热扩散阴极研究中的应用

对热扩散阴极表面微区发射状态进行原位观察和分析一直是热阴极研究的重要课题.本文着重介绍深紫外激光光发射电子/热发射电子显微镜的基本原理及其在热扩散阴极研究中的典型实例.系统配备了高温激活所用的加热装置,样品可被加热至1400℃.系统具有光发射电子、阴极热发射电子、光发射电子和阴极热发射电子联合三种电子成像模式.应用表明,对于热扩散阴极而言,深紫外激光光发射电子像适于呈现阴极表面的微观结构形貌;热发射电子像适于反映阴极表面的本征热电子发射及均匀性;光电子和热电子联合成像适于对阴极表面的有效发射点做出精确定位.     

基于沉淀工艺制作四脚氧化锌纳米材料场致发射阴极的研究

采用沉淀法制备四脚氧化锌纳米材料场致发射阴极，将阴极和荧光屏封装起来抽真空并对屏施加电压，测试阴极的发射电流和荧光屏的发光亮度.利用沉淀法制备出面积为(13×15) cm²的阴极，测试结果表明，硅酸钾体积百分比在50×10^-3—83×10^-3范围，硝酸钡浓度在50×10^-4—77×10^-4 M范围，四脚氧化锌的浓度在82×10^-4—12×10^{-3相似文献}   

复合阴极材料发射特性分析

 基于对爆炸发射点火机制的分析,提出了介质增强场致爆炸发射的设想,研制并实验研究了金属-介质复合阴极的电子发射特性;同时,基于对表面闪络爆炸发射机制的分析,研制出了石墨-碳纤维复合阴极并进行了初步实验研究。研究结果表明,金属-介质复合阴极与石墨 碳纤维复合阴极电子发射密度均超过17 kA/cm²,使用寿命预计超过10⁵次。     

生长温度对纳米氧化锌场发射性能的影响

采用锌粉和银粉为蒸发源,用热蒸发法不同温度下制备了四针状纳米氧化锌,并以单独的锌粉做对照。采用扫描电子显微镜(SEM)观察其形貌,X射线衍射(XRD)谱表征其晶体结构。采用丝网印刷方法将其制备为场致电子发射阴极,将阴极与印刷有荧光粉的阳极板组装成二极结构场致发射显示屏,并进行了场致电子发射特性对比实验。结果表明较高温度制备的氧化锌具有较好的场致发射性能;掺杂银粉的蒸发源制备的样品的发射性能明显优于没有掺杂银粉的样品。实验证明ZnO是一种优良的场致发射冷阴极材料,在真空电子方面具有广阔的应用前景。     

碳纳米管阴极强流脉冲发射特性实验

 在2 MeV直线感应加速器注入器平台上研究了采用浸渍涂覆方法制备的大面积碳纳米管阴极发射体的强流发射特性。研究结果表明：在脉冲高压电场下,碳纳米管阴极具有强流电子束发射能力,发射电流密度较大;碳纳米管阴极发射电子过程为场致等离子体发射。实验过程中,阴极端取样电阻环收集到的最大发射电流达350 A,阳极端法拉第筒收集的发射电流为167 A,最大阴极发射电流密度为19.4 A/cm²。     

Work function distribution for W-Ir mixed metal matrix cathodes

Mixed metal matrix cathodes have inherent non-uniformity and patchiness of emission due to the presence of two-alloy phase structure on the surface. I-V characteristics of cathode studied in a close spaced diode configuration is one of the easy and cost effective methods to estimate the variation of work function on the cathode surface. Tungsten iridium mixed metal matrix dispenser cathodes of Ø1.4 mm (80 wt.% W-20 wt.% Ir) have been fabricated in the laboratory and their I-V characteristics have been investigated in diode configuration. In this paper the model suggested by Tonnerre et al. has been used to find out the work function distribution of W-Ir cathodes from I-V characteristics. An attempt has been made to correlate the microstructure with the work function values.     

金属基底对石墨烯薄膜阴极气体击穿稳定性影响

利用石墨烯二维材料极好的场发射能力和发射稳定性,提出了石墨烯阴极提高气体开关击穿稳定性的技术路线。采用化学气相沉积法和基底腐蚀转移法两种方法制备金属基底石墨烯薄膜阴极。利用扫描电子显微镜和拉曼光谱表征了石墨烯薄膜阴极质量,确认了石墨烯层数和均匀性。实验研究了两种石墨烯薄膜阴极气体开关,在微秒脉冲均匀电场作用下的击穿特性,获得了击穿电压幅值和分散性的变化规律。结果表明:当气体为0.6 MPa N2、电极间距为5 mm时,铜基底石墨烯薄膜阴极平均击穿电压为85.9 kV,相对标准差为3.2%;不锈钢基底石墨烯薄膜阴极平均击穿电压仅为59.8 kV,相对标准差为2.4%。当两种阴极击穿电压均为80 kV时,相对标准差比较,不锈钢基底仅为铜基底的44%。分析认为,不锈钢基底石墨烯薄膜质量优于铜基底,石墨烯薄膜导致阴极表面微观场增强因子更高,表面分布更均匀,在电场作用下场致发射产生均匀稳定的大量初始电子流,降低了气体开关击穿电压,有效提高了击穿稳定性。     

Sc2O3-W matrix impregnated cathode with spherical grains

Sc₂O₃-W matrix cathodes have been prepared by using a liquid-liquid doping method combined with high-temperature sintering. The microstructure and physical behavior of active substances of scandia-doped tungsten matrix and impregnated cathode has been studied by SEM and AES methods. The results show that the matrix has a homogeneous structure composed of W grains with spherical shape and superfine Sc₂O₃ particles dispersed uniformly over and among W grains. After impregnation, this Sc-type impregnated cathode has high emission capability. Space-charge-limited current density could reach 52 A/cm² at 850 °C_b. The high emission results from a Ba-Sc-O active layer with a thickness of about 80 nm, which is formed at the cathode surface during the activation period. Both the decrease of the thickness of active surface layer and the decrease of the content of Sc at the surface could lead to the degradation of current density during operation.     

中间层Re的加入对覆膜钡钨阴极性能的改善

研究了一种新型的覆膜钡钨阴极——双层膜(Os-W/Re膜)钡钨阴极.对这种新型阴极的发射性能进行了测试，重点对其老炼前后表面薄膜的微观形貌进行了分析，表明中间层Re膜的加入使覆膜钡钨阴极的性能得到了改善.通过对Os-W双元合金膜钡钨阴极和Os-W/Re双层膜钡钨阴极发射特性的比较，发现Os-W/Re双层膜阴极的直流发射性能好于Os-W合金膜阴极.对两种阴极激活后发射表面的X射线光电子能谱分析表明，Os-W/Re双层膜阴极激活后表面形成的三元合金膜是其发射特性优于Os-W合金膜阴极的主要原因.应用扫描电子显微镜分析比较两种阴极激活老炼后的表面状态，结果表明：Os-W合金膜阴极在老炼一段时间后，其表面薄膜出现开裂，这会导致阴极发射均匀性下降；而Os-W/Re双层膜阴极在同样老炼条件下，发射表面薄膜均匀并保持完整，从而确保覆膜钡钨阴极发射均匀性和工作可靠性. 关键词： 双层膜钡钨阴极 Os-W/Re膜 Os-W膜 薄膜开裂     

Fast turn-on characteristics of tungsten-based dispenser cathodes. II

In the Proceedings of the 1982 Tri-Service Cathode Workshop, the authors described studies of the reactivations of tungsten-based dispenser cathodes following poisonings of the kind expected during shelf storage of a microwave tube [Appl. Surface Sci. 16 (1983) 73]. Further work on the problems of reactivation following such poisoning is described here. In addition to coated (“M”) and uncoated tungsten matrix cathodes, the tungsten-iridium mixed metal matrix (“MM”) cathode has been studied. In general reproducible results have been obtained from different examples of the same type of “M” and uncoated cathodes. However, although some “MM” cathodes have exhibited good reactivation characteristics, a large variation has been observed between different examples of “MM” cathodes. The composition of the impregnant in the dispenser cathodes has been found to be an important factor in determining the reactivation rate of a cathode. As the barium oxide concentration in the impregnant increases, the cathode will recover faster from a poisoning exposure. Studies of the poisoning caused by combinations of different gases suggest that poisoning will occur if there is a sufficient exposure of a poisoning agent, regardless of the total exposure. The exposures necessary to poison a cathode are so small, that poisoning of the cathode appears probable during shelf storage of a microwave tube. The reactivation results have been summarised in terms of the times and temperatures required to achieve both a given current density and a given degree of reactivation from a poisoned cathode. The studies also indicate that the limiting step during the reactivation process involves the dispensing of fresh material to the cathode surface rather than the desorption or conversion of a poisoned surface layer.     

Changes in surface chemistry of an Ir---W mixed metal coated cathode during activation

A comparative study has been made between a mixed metal (60% Ir-40%W) coated cathode and a “B” cathode during activation and also in their respective steady states. The rate limiting factor in the activation of the coated cathode is the oxidation of the initial Ba type surface to a BaO type surface. Since on the “B” cathode Ba and O emerge together, its activation is faster than the coated cathode. In the steady state of operation, both cathodes exhibit a surface near BaO stoichiometry which is the optimum composition for the minimum work function. This work function is about 0.2 eV lower on the coated cathode than on the “B” cathode. An accelerated life test at 1575 K indicated a gradual decrease of the Ir concentration in the coating.     

单壁碳纳米管在场发射显示器中的应用研究

采用丝网印刷法将利用电弧放电法制备的单壁碳纳米管印刷在玻璃板上作为场发射显示器阴极材料，利用荧光粉阳极测试了其发光亮度，并研究其场发射性能.实验结果表明，单壁碳纳米管作为场发射显示器阴极材料具有较低的开启电场和较大的场发射电流密度，显示出良好的场发射特性.     

Diffusion and desorption of barium and oxygen on tungsten dispenser cathode surfaces

Auger measurements have been made on the concentration of barium and oxygen diffusing out of a pore and slot onto the surface of a simulated tungsten dispenser cathode. Profiles of concentration vs distance from the source were obtained at different temperatures. It is found that at cathode operating temperatures very little gradient of oxygen concentration exists on the surface, and under steady state conditions Ba is the main diffusing species. Ba diffusion distances derived are consistent with previous measurements. However it is found that this distance increases with concentration in spite of the fact that the Ba surface lifetime decreases with concentration. Time dependent measurements made on a clean surface show that the rate of Ba and O build up is limited by the supply rate of oxygen to the surface. This supply rate is not diffusion limited but seems to be limited by the mechanism generating free oxygen. A comparison of emission microscope measurements on a tungsten matrix dispenser cathode with the simulated cathode data indicates that similar oxygen generation processes may be controlling the activation of these cathodes.     

热阴极径向温度非均匀性对本征发射度的影响

从热发射理论出发,推导了非均匀发射阴极的均方根本征发射度的一般计算形式。针对一种最常见的温度径向分布近似模型,给出了均方根发射度随温度非均匀性变化趋势的理论数值解。基于有限差分法粒子仿真技术统计了热阴极的本征发射度,仿真结果与理论解一致,验证了非均匀发射热阴极本征均方根发射度一般形式的正确性。结果表明,径向温度非均匀性引起均方根发射度显著变化,非均匀系数为10%时引起均方根发射度下降约15%。本文建立的理论形式和仿真方法可以有效评估束流品质控制目标和工程热设计之间的依赖关系,以指导高效费比的工程设计。