射孔孔眼中散射超声脉冲波的FEM模拟

采用有限元素法 ,分别数值计算了平底孔道、台阶式孔道和尖劈状孔道等 3种孔眼模型中不同中心频率 (10 0 k Hz、5 0 0 k Hz、1MHz)的散射超声脉冲波。计算结果表明 ,无论选用哪一种孔底模型 ,均可以得到较为明显的对应于孔底的声波信号。但是 ,孔道越不规则 ,使用的超声信号的主频越高 ,则孔底信号越差。为了兼顾孔底信号质量和信号采集、传输的代价 ,在未来的检测仪器中应采用尽可能低的测量频率 (低于 5 0 0 k Hz)     

Numerical simulation of flying phenomena of the running tape on rotating drum

This paper analyzes the running mechanism of flexible and thin tape above rotating protrusion through a numerical simulation. The scope of analysis is confined to the phenomena of elastohydrodynamic lubrication between the rotating drum with a protrusion and the running tape. This model is based on the modified Reynolds equation and the equation of plate considering the effect of geometric nonlinearity and geometry of protrusion. Finite element method of Bubnov-Galerkin type is adopted as a numerical simulation technique to solve the above two coupled nonlinear equations. In numerical simulation, the influences of tape tension and protrusion velocity are evaluated in simple model. In complex models, the reciprocal action of two protrusions is simulated.     

基底元素表面富集与扩散阻档层

根据An－Ag系统以及An－Cu系统的扩散系数计算，提出了扩散阻挡层模型。利用这个模型对Au－Ag系统进行有关实验，得利了较好的验证。     

A scheme to randomly generate surface dust points for the 3D complex variable boundary element method (CVBEM)

A scheme to randomly generate dust points on the surface of a three-dimensional (3D) object is proposed. This scheme will potentially eliminate the bias of a density of points which are approximately equally spaced on the surface, as well as eliminate possible weighting requirements for areas of higher density. This method has the potential to reduce computational effort, as fewer points might be required to define the surface area. The global trial function vector can be assigned to these dust points and then entered into the complex variable boundary element method (CVBEM) commercial code. This scheme can be applied to each piece of a system that is comprised of a connected multiple geometry. A noticeable benefit of this approach is that the same problem can be studied several times, using a new random distribution of surface points each time. The smallest error can then be determined and that run selected. The Mathematica code used to generate the scheme is attached as an appendix.     

大功率柴油机连杆三维精细分析

连杆作为柴油机的关键零部件，其刚度和强度对于柴油机的性能和功率的提高起到至关重要的作用。采用MSC／MARC程序及三维多体接触的方法，对G32柴油机连杆的应力场和位移场进行了数值模拟。进而为降低机械负荷、改善应力分布和进一步强化奠定基础。     

From the individual element test to finite element templates: Evolution of the patch test

This paper starts a sequence of three articles that follow an unconventional approach in finite element research. The ultimate objective is to construct high-performance elements and element-level error estimators for those elements. The approach takes off from our previous work in high-performance elements and culminates with the development of finite element templates. The present paper concentrates on the patch test and evolved versions of the test that have played a key role in this research. Following a brief review of the historical roots, we present the Individual Element Test (IET) of Bergan and Hanssen in an expanded context that encompasses several important classes of new elements. The relationship of the IET to the multielement forms A, B and C of the patch test and to the single-element test are investigated. An important consequence of the IET application is that the element stiffness equations decompose naturally into basic and higher-order parts. The application of this decomposition to the “sanitization” of the non-convergent BCIZ element is described and verified with numerical experiments. Two sequel papers in preparation are subtitled ‘the algebraic approach’ and ‘element-level error estimation’. These apply the fundamental decomposition to the derivation of templates for specific mechanical elements and to the construction of element-level error estimators, respectively.     

基于Adaline的数控系统位置控制器研究

针对机床数控系统进给位置控制的性能要求,必须根据其工作方式和误差情况实行变增益控制策略,才能较好地兼顾动态和静态指标,为此,选用自适应线性神经元(Adaline)代替原有的比例环节,可以获得相应的控制性能。经数字仿真和实际使用表明,在数控系统中引入人工神经网络控制思想是合理可行和有效的,并且还可以进一步通过硬化实现,达到实时在线控制的目的。     

Thermal Analysis of CNT-Based Nano-Composites by Element Free Galerkin Method

This paper deals with the thermal analysis of carbon nanotube (CNT) based composites by meshless element free Galerkin method. Cylindrical representative volume element (cylindrical RVE) has been chosen to evaluate the thermal properties of nano-composites using multi-domain and simplified approaches. The values of temperature have been calculated at different points and plotted against RVE length and RVE radius. A sensitivity analysis of RVE as well as CNT dimensions has been carried out in detail. The present computations show that the equivalent thermal conductivity is a function of CNT length, CNT radius, RVE length and RVE radius. Based on present numerical simulations, an approximate formula is proposed to calculate the equivalent thermal conductivity of nano-composites. The results obtained by simplified approach have been found in good agreement with those obtained by multi-domain approach.     

摇臂参数设计方法

建立了中小功率内燃机常用摇臂参数化设计模型。采用可变参数构成摇臂结构，并作结构的有限元网络，此后再进行有限元分析，计算出摇的质量、刚度、转动惯量 力。使摇臂的设计归结为几个主要参数的优选。实例分析表明，计算值和实测值基本相符，优选出的摇避设计优于原设计。     

CNC机床结构动态设计方法研究

提出机床结构动态设计基本原则。以某数控弧齿铣齿机为研究对象,应用相关的动态设计原则,通过变量化设计与有限元分析,对该机床进行结构动态设计。结果表明,应用该方法设计的机床结构具有良好的动静态特性。