流量自动控制的设计与实现

文章通过分析多相流模拟井的实际工作要求 ,提出了简单实用的流量自动控制模型。应用成型的计算机数据采集和控制模块及稳定可靠的流量控制部件 ,实现了各相流量的自动控制过程。该流量自动控制系统调节精度高、速度快、整体造价低 ,在实际应用中取得了良好的效果。     

聚合物驱流线数值试井解释模型及其应用

针对生产和关井两个阶段分别建立了考虑复杂因素影响的聚合物驱流线数值试井解释模型，两个阶段均考虑了油藏非均质性、聚合物驱、油水两相流、多井等因素的影响。该流线试井解释模型采用最新的流线方法进行一维求解，具有更高的求解速度和稳定性，同时它比现有模型更加接近于油藏真实环境，具有更高的现场实用性。     

Al2O3/TiB2/SiCw三元复合材料的力学性能及显微结构

以Al₂O₃为基体,SiC晶须和TiB₂颗粒两种增韧剂,采用热压烧结工艺制备了Al₂O₃/TiB₂/SiC_w三元复合陶瓷材料。研究了热压工艺参数对材料致密度的影响和晶须含量对该复合材料的力学性能和显微结构的影响。结果表明;随晶须含量的增加,该复合材料的热压温度和保温时间需要相应的增加;晶须拔出、裂纹偏转和晶须的桥接为该复合材料的主要增韧机理;随晶须含量的增加,该材料的室温断裂韧性增加;该材料的断裂韧性随温度的升高而呈增大趋势,并且晶须含量越高,材料的高温断裂韧性增幅越大。     

ZrSiO4/Al2O3烧结氧化铝-莫来石复相陶瓷微观结构的研究

将氧化铝和锆英石混合物试样分别在1350℃、1550℃下烧成，结果发现在1350℃烧成、保温3h的样品中有莫来石生成，而在1550℃烧成、保温3h的情况下却未发现莫来石生成，本文对此作了分析和探讨。关键词：氧化铝一莫来石，复相陶瓷，微观结构。     

NUMERICAL SIMULATION OF THE GAS-PARTICLE FLOW IN RISERS I: THE MACRO FLOW BEHAVIOR

The steady gas-particle flow in risers under variant operating conditions was predicted based on a k-ε-k_p-ε_p-Θ two-fluid model, which describes the dense turbulent gas-particle flow by the Eulerian method, considering the turbulence of both gas and particles as well as the particles' collisional effects. Much information on the macro flow behavior in risers, such as the profiles of local particle axial velocity, solids volume fraction, and solids mass flux in different operating regimes was obtained, and the predicted results show satisfactory agreement with experimental data. Further analysis of the predictions gives the comprehension of flow characteristics on the macro scale.     

原位合成TiB2-TiCx复相陶瓷的显微组织

应用光学显微镜(OM)、X射线衍射(XRD)、透射电镜(TEM)和扫描电镜(SEM)对原位合成的TiB2-TiCx复相陶瓷显微结构进行了分析。并分析了Ti-B4C反应的原位生成机理。结果表明,Ti3B4相稳定存在于生成物中,其形态与形成温度和反应机理有关。     

Ti3SiC2/4SiC复相陶瓷的高温力学性能研究

为了进一步了解Ti3SiC2/nSiC复合材料优良的综合性能,特别是其高温力学性能,本文以热等静压原位合成技术制备的Ti3SiC2/4SiC复相陶瓷为试验材料,对其高温拉伸和高温弯曲行为进行研究。结果表明:Ti3SiC2/4SiC复相陶瓷的高温抗拉强度比室温抗拉强度高;Ti3SiC2/4SiC复相陶瓷的高温抗弯强度在900℃出现一极大值,1000℃后具有好的高温塑性。     

基于Potts模型的隐式曲面上的图像分割方法

针对隐式曲面上多相图像分割的问题,基于曲面的隐式表达、隐式曲面上的内蕴梯度等概念,将用于平面图像分割的Potts模型推广.首先对于隐式封闭曲面和隐式开放曲面,分别给出Potts模型的推广形式.然后对于传统梯度降方法计算效率低的问题,为曲面上的Potts模型设计了Split Bregman算法和对偶方法,并在对偶方法的基础上提出了一种改进的快速算法.多个数值实验结果表明,所提出的曲面上的Potts模型能有效地分割闭/开曲面上的分段常值图像,并且新的改进对偶方法在计算效率方面优于其他两种方法.     

The Yield Stress of Gas/Liquid/Fibre Suspensions

Yield stress measurements of gas/liquid/fibre suspensions, were conducted to examine the effect of gas concentration as well as fibre concentration. Obtaining a well mixed stable pulp suspension with gas was difficult. A transparent model system consisting of glass fibres submersed in refractive index matched liquid gave stable suspensions and had the additional advantage of allowing visual observations. The measurements were performed in a baffled shear tester and concentrations were in the range of 0–12.5% vol. gas and 8–14% wt. fibres. Results show that yield stress decreases with increasing gas fraction for constant fibre concentrations. Since the fibre concentration is defined in the liquid phase, the amount of fibres decreases with increasing gas concentration. This fact alone partly explains the decrease in yield stress, but the gas also has a direct impact on the decrease in yield stress. Further, as expected, the yield stress increases with increasing fibre concentrations when the gas fraction is kept constant.