Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

开关磁阻电机结构性转矩脉动抑制方法

开关磁阻电机具有结构简单、成本低和调速范围广等优势,但其双凸极结构和控制器的开关特性,导致存在转矩脉动现象,使得抑制转矩脉动成为焦点问题。首先从开关磁阻电机的结构和运行机理出发,针对线性解析方法难以分析转矩特征的问题,建立电机有限元模型求解出转矩特征并进行样机验证试验。分析样机结构参数对转矩脉动的影响,针对结构参数耦合问题,选择NSGA-Ⅱ算法在参数优化平台上对样机结构参数进行多目标寻优,在保证优化后样机的转矩脉动系数和平均转矩均优于初始电机的条件下,最终获得样机最优化结果。结果表明,不同结构参数对电机转矩的影响有较大的差异,对结构参数的优化能有效地抑制转矩脉动,该参数优化方法可以为开关磁阻电机结构性转矩脉动抑制提供参考。     

Designed damping controller for SSSC to improve stability of a hybrid offshore wind farms considering time delay

This paper presents the stability improvement results of hybrid doubly fed induction generator (DFIG)-based and permanent magnet generator (PMG)-based offshore wind farms (OWFs) using a static synchronous series compensator (SSSC). An adaptive-network-based fuzzy inference system (ANFIS) controller of the proposed SSSC is designed to render adequate damping characteristics to the studied system. A frequency-domain approach based on a linearized system model using eigenvalue technique analysis is performed. A time-domain scheme based on a nonlinear system model subject to a three-phase short circuit fault at infinite bus with variations in the signal transmission delays has also been investigated to compare the damping of the studied system in cases of with and without controller. The simulation results with MATLAB/SIMULINK toolbox have been presented. It can be concluded from the simulation results that the proposed SSSC joined with the designed ANFIS damping controller can offer adequate damping performance to the studied hybrid DFIG-based and PMG-based OWFs under severe disturbance.     

100 MeV质子回旋加速器二期辐照效应管道设计

针对中国原子能科学研究院100 MeV质子回旋加速器上的单粒子效应辐照装置进行了二期管道设计，采用八极磁铁校正法对束流进行了扩束及均匀化，最终在靶上得到了一个30 cm×30 cm、均匀性好于92%的均匀分布的束斑，满足了单粒子效应实验的需求。为降低靶站处的束流能散及中子本底，采用两级降能的方案，在偏转磁铁前放置1个降能片，将能量分为100 MeV和40 MeV两档，并分别针对这两个能量点进行方案设计，束流利用率均在42%以上。公差分析结果表明，四极磁铁对靶上束斑均匀性的影响大于八极磁铁，安装过程中应优先保证四极磁铁的安装公差。     

基于时频域的卷积神经网络运动想象脑电信号识别方法

针对目前运动想象脑电（EEG）信号识别率较低的问题，考虑到脑电信号蕴含着丰富的时频信息，提出一种基于时频域的卷积神经网络（CNN）运动想象脑电信号识别方法。首先，利用短时傅里叶变换（STFT）对脑电信号的相关频带进行预处理，并将多个电极的时频图组合构造出一种二维时频图；然后，针对二维时频图的时频特性，通过一维卷积的方法设计了一种新颖的CNN结构；最后，通过支持向量机（SVM）对CNN提取的特征进行分类。基于BCI数据集的实验结果表明，所提方法的平均识别率为86.5%，优于其他传统运动想象脑电信号识别方法；同时将该方法应用在智能轮椅上，验证了其有效性。     

Robust Control of Permanent Magnet Synchronous Motors

In this paper, permanent magnet synchronous motors (PMSMs) are investigated. According to the feature of PMSMs, a novel state equation of PMSMs is obtained by choosing suitable state variables. Based on the state equation, robust controllers are designed via interval matrix and PI control idea. In terms of bilinear matrix inequations, sufficient conditions for the existence of the robust controller are derived. In order to reduce the conservation and the dependence on parameter, the control inputs of PMSMs are divided into two parts, a feedforward control input and a feedback control input, and relevant sufficient conditions for the existence of the controller are obtained. Because of the suitable choice of state variables, the proposed control strategies can cope with the load uncertainty and have robustness for disturbance. Finally, simulations are carried out via Matlab/Simulink soft to verify the effectiveness of the proposed control strategies. The performance of the proposed control strategies are demonstrated by the simulation results.      

开关磁阻直线电机的设计及其推力优化

设计了一种开关磁阻直线电机,使用JMAG软件对其进行了仿真和优化。进行了推力公式的推导,研究了导通顺序和初始位置对电机推力的影响,并分析了三种典型情况的磁力线分布。对电机的定子和动子的齿部和轭部高度、宽度及铁耗进行仿真优化,得出了最优参数。将有取向硅钢应用于该电机,研究了推力与轧制角的关系,并与使用普通硅钢的开关磁阻直线电机进行了对比,推力有一定提升。提出在动子齿部开切向槽的方案,结果表明,开切向槽对推力的影响较小,并能显著减小推力波动。     

卫星激光通信粗跟踪系统复合控制策略

针对卫星激光通信粗跟踪系统的跟踪稳定精度指标要求高的特点,建立了基于永磁同步电机直接驱动的粗跟踪系统模型并进行了跟踪稳定误差分析。在采用传统PID控制策略存在跟踪误差较大、动态性能较差等不足的基础上,提出了一种基于粗跟踪系统的改进型前馈复合控制策略。从理论上分析了前馈复合控制策略提高了粗跟踪系统的动态性能,为降低跟踪稳定误差提供了改善方案。地面实验验证结果表明,与传统控制策略相比,改进型复合控制策略极大地降低了系统的动态跟踪误差,动态跟踪误差由606μrad降低至13μrad(1δ)。进一步的在轨实验也验证了改进型复合控制策略的合理性和先进性,总体指标满足了卫星激光通信终端的极高精度要求。本文所提出的控制策略对其他高性能跟踪伺服系统设计也具有较大的借鉴意义。     

基于DSP的多元数据同步采集与存储系统的设计与实现

从硬件和软件两个角度出发,介绍基于DSP的多元数据同步采集与存储系统的组成、工作模式以及功能的测试。系统主要由上位机和数字采集与存储单元组成,其中数字采集与存储单元的硬件部分包括电源模块,值班电路模块,数据采集模块,数据存储模块,时钟同步模块。系统采用DSP作为中央处理芯片,利用经过同步后的秒脉冲作为触发信号,实现同步数据采集。以CF卡作为存储介质,实现数据自容式存储。软件部分实现自检、同步、数据采集存储功能。经过测试,系统工作稳定,功能正常,同步精度在100ns以内。     

基于AMESim的液压马达加载系统研究

液压马达作为液压系统的执行元件在工程机械上广泛应用,针对液压马达加载工况下的输出特性,利用Simulink和AMESim软件对系统进行联合仿真建模,并对系统的运行状态、控制性能、回收性能进行研究,对液压马达加载系统的设计和改进具有重要的参考意义。