Boronic acid‐based thin films that show saccharide‐responsive multicolor changes

A novel saccharide sensor that displays a distinct color change resembling a “traffic signal” was developed. By copolymerizing boronic acid and amine monomers on a glass plate, a boronic acid‐containing thin film was obtained. Anionic blue and yellow dyes were adsorbed on the thin film, and the film was immersed in aqueous saccharide solutions containing a cationic red dye. With increase in the saccharide concentration in the solution, the thin film changes color from green to red via yellow. The observed distinct changes in color were attributed to a stepwise release and binding of dyes. The sensitivity of the saccharide sensor was dependent on the monomer composition of the thin film and increased with increasing the boronic acid content. The pH of the saccharide solution was another key factor affecting the sensing behavior, and glucose‐responsive color changes were significantly enhanced at pH 7.8. By optimizing these conditions, significant color changes in response to glucose were achieved. Saccharide selectivity was found to be in the following order: fructose > glucose > galactose = mannose > sucrose. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42679.     

Capability of Utilizing CYP3A5 Polymorphisms to Predict Therapeutic Dosage of Tacrolimus at Early Stage Post-Renal Transplantation

While CYP3A5 polymorphisms are used to predict the initial dosage of tacrolimus therapy, the predictive capability of genetic information for dosing at early stage post-renal transplantation is unknown. We investigated the influence of polymorphisms over time. An initial oral dose of modified-release once-daily tacrolimus formulation (0.20 mg/kg) was administered to 50 Japanese renal transplant patients every 24 h. Stepwise multiple linear regression analysis for tacrolimus dosing was performed each week to determine the effect of patient clinical characteristics. The dose-adjusted trough concentration was approximately 70% higher for patients with the CYP3A5*3/*3 than patients with the CYP3A5*1 allele before the second pre-transplantation tacrolimus dose (0.97 (0.78–1.17) vs. 0.59 (0.45–0.87) ng/mL/mg; p < 0.001). The contribution of genetic factors (CYP3A5*1 or *3) for tacrolimus dosing showed increased variation from Day 14 to Day 28 after transplantation: 7.2%, 18.4% and 19.5% on Days 14, 21 and 28, respectively. The influence of CYP3A5 polymorphisms on the tacrolimus maintenance dosage became evident after Day 14 post-transplantation, although the tacrolimus dosage was determined based only on patient body weight for the first three days after surgery. Tacrolimus dosage starting with the initial administration should be individualized using the CYP3A5 genotype information.     

Design of multi‐input multi‐output minimum‐phase state control system with decoupling and feedforward compensation

This paper discusses the design of decoupling control for a multi‐input multi‐output (MIMO) linear system. A new configuration of the prepositional tandem matrix is presented as a decoupling compensator, and minimum‐phase state control is applied to the resulting decoupled system. In general, non‐minimum‐phase characteristics often accompany decoupled systems. Feedforward compensation makes the non‐minimum‐phase effect of each decoupled scalar system change to the delay time. A numerical example is given for the MIMO linear system, which conventionally results in non‐minimum‐phase systems. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 176(2): 53–61, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21117     

Scaling prospect of optically differential reconfigurable gate array VLSIs

Dynamic reconfigurable devices present new computational paradigms because programmable devices’ activity and performance can be improved dramatically by increasing its reconfiguration frequency. Therefore, this paper presents designs of optically differential reconfigurable gate array (ODRGA) VLSIs using 0.18 μm and 0.35 μm CMOS process technologies. Although they are a type of programmable gate array, they can be reconfigured optically in nanoseconds. This paper also discusses future scaling prospects of ODRGA-VLSIs.     

Surface Waves on Superfluid <Superscript>4</Superscript>He Under Reduced Gravity

Superfluid ⁴He was produced on a small jet plane for the first time using a small GM-refrigerator to condense the liquid and a scroll pump to get the superfluid by evaporation. The surface wave on superfluid under 0.5g _E, 0.1g _E and 0.05g _E, together with 2g _E and 1g _E, was successfully examined by an optical method utilizing parabolic flight. Here, g _E is the gravitational constant on the ground. Assuming that only the fundamental mode was excited as determined by the sample cell width, the resonance peak in the frequency domain was well reproduced by the gravity wave with corresponding gravity constant.     

Determination of the glass transition temperature of polymer/layered silicate nanocomposites from positron annihilation lifetime measurements

The glass transitions of acrylonitrile-butadiene rubber (NBR)/organoclay nanocomposites with various silicate contents were investigated using positron annihilation lifetime spectroscopy (PALS). The nanocomposites were prepared through melt intercalation of NBR with various concentrations of organoclay (OC30B) modified with the organic modifier, methyl tallow bis(2-hydroxyethyl) quaternary ammonium (MT2EtOH), i.e., Cloisite^® 30B. X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM) measurements of the NBR/OC30B nanocomposites showed that the NBR chains were intercalated between the silicate layers, thereby increasing the gallery heights of the organosilicates. The glass transition temperature of NBR was determined using differential scanning calorimetry (DSC). However, it seemed to be very difficult to clearly resolve the very small differences in T_gs caused from various loading of nanosized silicate in NBR/OC30B nanocomposites. Hence, we performed positron annihilation lifetime spectroscopy (PALS) on NBR/OC30B nanocomposites containing various amounts of OC30B (1-10 wt%). Significant changes in the temperature dependencies of free volume parameters (i.e., lifetimes and intensities) were observed at the transition temperature, T_g,PALS, and the T_g,PALS values were found to increase with increasing organoclay content in the samples. These observations are consistent with PALS having a higher sensitivity in the detection of very small changes in free volume properties. The present findings thus highlight the usefulness of PALS for studying phase transition phenomena in polymeric materials with nanoscale structural variations.     

Zirconia Coating on Stainless Steel Sheets from Organozirconium Compounds

The stability and the coating characteristics of a variety of organozirconium compounds have been investigated to coat ZrO₂ films on stainless steets for the improvement of heat resistance against oxidation. Zirconium tetraoctylate and zirconium tetrakis(acetylacetonate) were found to be more stable than zirconium alkoxides in an ambient atmosphere. The ZrO₂ films from zirconium alkoxides became white and discontinuous when the thickness of the films exceeded about 200 Å (20 nm). On the other hand, transparent ZrO₂ films were obtained from zirconium tetraoctylate and zirconium tetrakis(acetylacetonate). The IR spectra of the films showed that the heat treatment at 400°C for 5 min produced organic-free ZrO₂ films. The heat resistance of stainless steel sheets against oxidation was improved by the ZrO₂ coating, depending on the film thickness.     

Beta tricalcium phosphate ceramics with controlled crystal orientation fabricated by application of external magnetic field during the slip casting process

Beta tricalcium phosphate (β-TCP) is a resorbable bioceramic that has hitherto been utilized in the medical field. Since it crystallizes in the anisotropic hexagonal system, properties such as chemical and physical ones are expected to depend on its crystal axis direction and/or on its crystal plane (anisotropy). Control of crystal orientation is thus important when used in polycrystalline form. Meanwhile, application of a strong magnetic field has been found to be a promising technique to control crystal orientation of anisotropic shape or structured crystals. In this work, we attempted to fabricate β-TCP ceramics with controlled crystal orientation by applying an external magnetic field during the slip casting process and subsequently sintering them at 1050 °C, below the β–α transition temperature. Application of a vertical magnetic field increased intensities of planes perpendicular to c-plane on the top surface, while a horizontal one with simultaneous mechanical mold rotation decreased it. These results indicated that crystal orientation of β-TCP ceramics were successfully controlled by the external magnetic field and together that the magnetic susceptibility of β-TCP is χ_c⊥ > χ_c//.     

Observation of the solid-state formation of a TTF–CA complex by terahertz spectroscopy

The solid-state synthesis of a tetrathiafulvalene–chloranil (TTF–CA) complex was demonstrated, and progress in the formation of the complex was monitored using a GaP Raman terahertz (THz) spectrometer. Clear transitions in the THz absorption spectra indicated that the mixture of TTF and CA became the black phase TTF–CA complex. The results of X-ray diffraction, Raman scattering, and FTIR spectra are presented as supporting evidence.