Sol-Gel Preparation and Spectroscopic Properties of Modified Sodium Silicate /Tartrazine Dye Nanocomposite

Silicon - Thin film nanocomposites of sodium silicate (80 SiO2 –20 Na2O)/ tartrazine dye (E102) prepared using sol gel process in acidic system. The change in the physicochemical properties...     

Interference analysis for asynchrounous OFDM/FBMC based cognitive radio networks over Rayleigh fading channel

In the future fifth generation networked society, devices will suffer from the asynchronous multi-carrier effect which impacts the user’s quality of experience. This paper investigates the timing misalignment effect on interference level in the context of a cognitive radio (CR) network. Our study considers both multicarrier techniques orthogonal frequency division multiplexing (OFDM) and filter bank multicarrier (FBMC). The originality of our paper consists in proposing a simple but accurate analytical model to evaluate our system’s performance in terms of interference level, signal-to-interference-plus-noise ratio and bit error rate. Specifically, two case studies are considered, a single-user case (one primary user and one secondary user) and a multi-user case with exact theoretical expressions of interference level. We had also made a comparison between OFDM and FBMC techniques. The most striking observation to emerge from our results is that the asynchronous interference is inversely propositional to timing offset even for the multi-user case, and that differences in the normalized interference level between the single/multi-user cases is barely perceived for the FBMC technique, proving its efficiency. Our simulations’ results had further strengthened our confidence in the suggested model. It shows that FBMC is best suited for CR networks since it provides BER improvements compared to OFDM.

     

Live video streaming service with pay-as-you-use model on Ethereum Blockchain and InterPlanetary file system

Wireless Networks - In centralized video streaming platforms, the platform owner, rather than the content producer, controls most of the content uploaded on the centralized video...     

Simulation of the deflected cutting tool trajectory in complex surface milling

Since industry is rapidly developing, either locally or globally, manufacturers witness harder challenges due to the growing competitivity. This urges them to better consider the four factors linked to production and output: quality, quantity, cost and price, quality being of course the most important factor which constitutes their main concern. Efforts will be concentrated??in this research??on improving the quality and securing more accuracy for a machined surface in ball-end milling. Quality and precision are two essential criteria in industrial milling. However, milling errors and imperfections, due mainly to the cutting tool deflection, hinder the full achieving of these targets. Our task, all along this paper, consists in studying and realizing the simulation of the deflected cutting tool trajectory, by using the methods which are available. In a future stage, and in the frame of a deeper research, the simulation process will help to carry out the correction and the compensation of the errors resulting from the tool deflection. The corrected trajectory which is obtained by the method mirror will be sent to the machine. To achieve this goal, the next process consists??as a first step??in selecting a model of cutting forces for a ball-end mill. This allows to define??later on??the behavior of this tool, and the emergence of three methods namely the analytical model, the finite elements method, and the experimental method. It is possible to tackle the cutting forces simulation, all along the tool trajectory, while this latter is carrying out the sweeping of the part to be machined in milling and taking into consideration the cutting conditions, as well as the geography of the workpiece. A simulation of the deflected cutting tool trajectory dependent on the cutting forces has been realized.     

Structural transition of a homopolymer in solvents mixture

The present work is aimed at studying the thermodynamic behaviour of a polymer in solvents mixture. Dynamic light scattering is used to measure the hydrodynamic radius of polyvinylpyrrolidone (M_w = 360,000 g/mol), in water/methanol solvents mixture, versus the mixed solvents composition at 25 °C. Then, we show that the polymer conformation adopts the Coil–Globule–Coil structure when the methanol molar fraction X_A is varied. This transition is attributed to solvent quality change which result from water and methanol complex formation. The polymer contraction rate calculated for each composition takes its maximum value at X_A = 0.17. Hildebrand theory assuming the solvents mixture as an equivalent solvent was used to analyze the change in mixed solvents quality. These changes can be attributed to dispersive forces in solvents mixture.     

“<Emphasis Type="SmallCaps">disassembly plan approach based on subassembly concept</Emphasis>”

A three-dimensional numerical model is established to study the temperature and fluid flow fields in the twin-wire gas metal arc welding (GMAW) process. The high-speed photography system is used to capture the images of the weld pool during the welding. Based on simulation and experimental results, the weld pool formation, convection, and stability in twin-wire GMAW process are investigated. Both “push-pull” and outward flow patterns exist in the twin-wire GMAW weld pool, which can contribute to decreasing the height of the bulge and increasing the width of the pool. The convection in the weld pool can proceed adequately, the arc force between the leading and trailing arcs is relatively balanced, surface tension normal force is uniform along the liquid channel, and the liquid channel is capillary stable, all of those contribute to the stability of the weld bead. The simulation results are in good agreement with those in the experiment.     

FPGA architecture of the LDPS Motion Estimation for H.264/AVC Video Coding

Motion estimation is a highly computational demanding operation during video compression process and significantly affects the output quality of an encoded sequence. Special hardware architectures are required to achieve real-time compression performance. Many fast search block matching motion estimation (BMME) algorithms have been developed in order to minimize search positions and speed up computation but they do not take into account how they can be effectively implemented by hardware. In this paper, we propose three new hardware architectures of fast search block matching motion estimation algorithm using Line Diamond Parallel Search (LDPS) for H.264/AVC video coding system. These architectures use pipeline and parallel processing techniques and present minimum latency, maximum throughput and full utilization of hardware resources. The VHDL code has been tested and can work at high frequency in a Xilinx Virtex-5 FPGA circuit for the three proposed architectures.     

Performance enhancement of the 3D OCDMA system by using dynamic cyclic shift and multi-diagonal codes

Photonic Network Communications - A new three-dimensional (3D) code is developed for spectral/time/spatial optical code division multiple access (OCDMA) system namely 3D dynamic cyclic...