Synthesis and slurry spray coating of barium strontium alumino silicate on SiC substrate

Barium strontium alumino silicate (BSAS); (Ba_0.6Sr_0.4Al₂Si₂O₈) was synthesized through solid state reaction between BaCO₃, SrCO₃, Al₂O₃ and SiO₂ subjected to wet milling in isopropanol for about 24 h. The sequence of the solid state reaction was studied by subjecting to DG/DTG from room temperature to 1550 °C. The crystallographic phase evolution was confirmed by X-ray diffraction of the powders calcined in the range 1000 to 1300 °C for 2 h. The monoclinic celsian phase obtained at 1300 °C, pelletized through uniaxial pressing was sinterable to 67 to 78% density in the temperature range of 1300 to 1500 °C. The density improved to 75 to 94% after ball milling for 76 h, while ZrO₂ addition further improved the density by 2%. The celcian phase of BSAS was dispersed in isopropyl alcohol, milled for about 24 h and spray coated on to plain SiC and mullite precoated SiC substrates. Sintering of coated samples and characterization for weight gain/loss, microstructure, scratch test prove that mullite + BSAS coating is more effective than single layer coating of BSAS on SiC substrates.     

Analytical Modeling of Threshold Voltage for Dual-Metal Double-Gate Gate-All-Around (DM-DG-GAA) MOSFET

Silicon - This paper presents, analytical modeling of surface potential,threshold voltage and DIBL for a Dual-Metal Double-Gate Gate-All-Around (DM-DG-GAA) MOSFET considering the parabolic...     

电磁脉冲辐射波模拟器双锥-平面线栅天线场分布规律

双锥-平面线栅结构的水平极化辐射波天线对辐射场半宽影响较小且架设方便、易于维护，掌握该型天线场分布规律是确定模拟器场均匀区、开展电磁脉冲效应实验的前提。利用天线理论研究双锥-平面线栅天线的场分布规律，结合数值模拟和实际天线试验对理论分析结果进行验证。结果表明：在天线结构和激励电压确定的条件下，双锥中心正下方辐射电场极化分量仅与测点到源的距离相关，二者呈反比；Oxz平面内以双锥中心为圆心的圆弧上任意一点辐射电场极化分量的幅值相等，并在同一时刻达到峰值；Oxz平面内同一水平线上的测点总辐射场幅值相等，方向沿测点所在圆弧的切线方向；各辐射场分量关于Oxz平面和Oyz平面对称分布；对于实际模拟器，地面反射会使辐射场波形下降沿陡降，导致地面附近辐射场半宽变小；线栅极板会影响附近的场分布，且极板外侧4个角点处的反射相对较强，其他位置辐射场分布与理论分析一致。     

Chromium-promoted preparation of forsterite refractory materials from ferronickel slag by microwave sintering

The chromium-promoted preparation of forsterite refractory materials from ferronickel slag was investigated by microwave sintering of the slag with the additions of sintered magnesia and 0–10 wt% chromium oxide (Cr₂O₃). The thermodynamic calculations revealed that the addition of Cr₂O₃ can promote the formations of spinel and liquid phase and maintain high content of forsterite below 1500 °C. The experimental results showed that there existed a stronger promoting effect of Cr₂O₃ additive on the properties of refractory materials in the microwave field than that in conventional sintering. It was attributed to the preferential formation and growth of spinel with stronger microwave absorption than other phases (e.g., enstatite), the existence of more forsterite, and the enhanced densification in association with the presence of more liquid phase at the same temperature. By microwave sintering of the mixture of ferronickel slag, 25 wt% sintered magnesia, and 4 wt% Cr₂O₃ at 1350 °C for 20 min, a superior refractory material with refractoriness of 1801 °C, thermal shock resistance of 6 times, bulk density of 2.97 g/cm³, apparent porosity of 1.4%, and compressive strength of 197 MPa was obtained. Compared with that prepared by conventional sintering at 1350 °C for 2 h, the refractoriness and thermal shock resistance were increased by 175 °C and 100%, respectively. The present study provided a novel method for preparing high-quality refractory materials from ferronickel slag and relevant industrial wastes.     

Numerical simulation analysis and experimental validation on wear/fracture mechanisms of polycrystalline cubic boron nitride superabrasives in high-speed grinding

In this study, a two-dimensional finite element model is proposed to investigate the wear/fracture mechanisms of polycrystalline cubic boron nitride (PCBN) superabrasives in high-speed grinding process. The special geometric microstructures of PCBN grains are constructed by using the classic Voronoi tessellation technique, and cohesive elements are embedded into the geometric model of PCBN grains as the potential crack propagation paths for simulating the wear/fracture behaviours of PCBN grains under grinding loads. The effects of uncut chip thickness per grain (a_gmax) on the stress distribution characteristics and wear/fracture behaviours of PCBN grains during grinding are discussed in detail. Results show that the wear behaviour of PCBN grains during grinding mainly occurs around the grain vertex region; however, the fracture behaviour, leading to the quick failure of PCBN grains, is prone to appear around the grain–filler bonding interface, which is usually on the opposite side of the in-feed direction. Moreover, to separate the PCBN grains from the macro-fracture during grinding, the uncut chip thickness per grain should be kept smaller than 1.0?µm to prevent the unfavourable fracture behaviour from appearing around the grain–filler bonding interface. Furthermore, the corresponding single-grain grinding trials are performed to validate the numerical simulation results by evaluating the wear/fracture morphologies of the PCBN superabrasives in the actual grinding operation.     

Development of cellulose nanofibrils reinforced polyvinyl alcohol films incorporated with alizarin for intelligent food packaging

Visual pH-sensing films were fabricated using cellulose nanofibrils (CNF) reinforced polyvinyl alcohol (PVA) and alizarin. The relationships between the ratio of PVA: CNF hydrogel (2:1, 1:1, 1:2) and the physical properties and colour response efficiency of indicator films were investigated. Fourier transform infrared spectroscopy of films evidenced alizarin and CNF was properly incorporated by physical interaction. A new weak X-ray diffraction peak appeared at 2θ = 22.4°, which was affected by the incorporation of CNF. The increase in the CNF content induced enhancements of thermal stability, tensile strength, water contact angle and colour sensitivity of the indicator films. The colourimetric films had a higher sensitivity to discolouration when exposed to acidic vapours than alkaline vapours. The films presented a remarkable colour change varied from purple in alkaline condition to yellow in acidic condition. Therefore, this colourimetric film can be used as a volatile acid sensor for intelligent packaging.     

Review on zirconate-cerate-based electrolytes for proton-conducting solid oxide fuel cell

The performance of low-to-intermediate temperature (400–800?°C) solid oxide fuel cells (SOFCs) depends on the properties of electrolyte used. SOFC performance can be enhanced by replacing electrolyte materials from conventional oxide ion (O^2-) conductors with proton (H⁺) conductors because H⁺ conductors have higher ionic conductivity and theoretical electrical efficiency than O^2- conductors within the target temperature range. Electrolytes based on cerate and/or zirconate have been proposed as potential H⁺ conductors. Cerate-based electrolytes have the highest H⁺ conductivity, but they are chemically and thermally unstable during redox cycles, whereas zirconate-based electrolytes exhibit the opposite properties. Thus, tailoring the properties of cerate and/or zirconate electrolytes by doping with rare-earth metals has become a main concern for many researchers to further improve the ionic conductivity and stability of electrolytes. This article provides an overview on the properties of four types of cerate and/or zirconate electrolytes including cerate-based, zirconate-based, single-doped cerate–zirconate and hybrid-doped cerate–zirconate. The properties of the proton electrolytes such as ionic conductivity, chemical stability and sinterability are also systematically discussed. This review further provides a summary of the performance of SOFCs operated with cerate and/or zirconate proton conductors and the actual potential of these materials as alternative electrolytes for proton-conducting SOFC application.     

Facile Synthesis of Fluorine Doped Rutile TiO2 Nanorod Arrays for Photocatalytic Removal of Formaldehyde

Catalysis Letters - It is crucial to explore a facile synthesis of rutile TiO2 nanorods anchored at carbon cloth at low temperature for applicable air purifier. Herein, antler-like TiO2 rectangular...     

Numerical Simulation on Design of Temperature Control for Side Heater in Directional Solidification System of Multi-Crystalline Silicon

In this paper, the transient numerical simulation was used to study the effects of temperature variation in three ways (the open downward parabola, the str