SIL验证与安全仪表系统的优化设计

安全仪表功能(SIF)回路是为了降低特定场景的安全风险而设置的,定级报告中SIF回路的功能描述是工艺设计的完整逻辑要求,包含关键动作及附件动作。安全完整性等级(SIL)验证属于概率学领域研究范畴,影响失效率的因素多且复杂。如果SIL验证无法通过,将造成大量的设计变更,浪费工程投资,影响工期。设计人员应关注SIL定级报告中关键动作的识别、要求平均失效概率以及SIF回路架构的约束。按照文中方法优化测量元件、逻辑控制器、执行元件及辅助元件的设计,可增加通过验证的概率。在没有预验证及安全要求规格书时,可以参考文中典型可通过SIL验证的SIF回路的经验架构进行优化设计,以减少工程变更。     

Simultaneous fractionation of multiple classes of polyphenols from honeybush tea using solid-phase extraction

The structural diversity of polyphenols and the inherent limitations of current extraction techniques pose a challenge to extract polyphenols using a simple and green method. Hence, in this study, a method was developed to simultaneously fractionate multiple classes of polyphenols by only varying ethanol-water solutions. Honeybush tea, which is rich in polyphenols, was selected as a model for this study. Solvent extraction followed by solid-phase extraction (SPE) was developed to obtain a polyphenol-rich fraction from six honeybush samples. Based on a gradient elution programme (10%, 30%, 50%, 70% and 90% (v/v) ethanol-water solution) of SPE, the Strata X cartridge showed a better recovery of most targeted polyphenols under 0.9 mL of the drying volume and 1 mL min⁻¹ of the dispensing speed. The elution programme for fractionating most polyphenols was as follows: single elution with 50% ethanol, followed by twice elution with 70% ethanol. The antioxidant capacity was used to analyse the differences among the polyphenol-rich fractions from six honeybush samples. Principal component analysis (PCA) revealed that unfermented C. genistoides (GG) has the greatest antioxidant capacity among the honeybush species studied. Additionally, mangiferin, isomangiferin and vicenin-2 were the main contributors to the antioxidant capacity in six honeybush fractions according to the correlation study.     

Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.     

Corrosion Behaviour of Type 316L Stainless Steel in Hot Caustic Aqueous Environments

Metals and Materials International - The corrosion behaviour of type 316L stainless steel in aqueous 30–50&nbsp;wt%. NaOH at temperatures up to 90&nbsp;°C has been elucidated....     

Investigating measurements of fine particle (PM2.5) emissions from the cooking of meals and mitigating exposure using a cooker hood

There is growing awareness that indoor exposure to particulate matter with diameter ≤ 2.5 μm (PM_2.5) is associated with an increased risk of adverse health effects. Cooking is a key indoor source of PM_2.5 and an activity conducted daily in most homes. Population scale models can predict occupant exposures to PM_2.5, but these predictions are sensitive to the emission rates used. Reported emission rates are highly variable and are typically for the cooking of single ingredients and not full meals. Accordingly, there is a need to assess PM_2.5 emissions from the cooking of complete meals. Mean PM_2.5 emission rates and source strengths were measured for four complete meals. Temporal PM_2.5 concentrations and particle size distributions were recorded using an optical particle counter (OPC), and gravimetric sampling was used to determine calibration factors. Mean emission rates and source strengths varied between 0.54—3.7 mg/min and 15—68 mg, respectively, with 95% confidence. Using a cooker hood (apparent capture efficiency > 90%) and frying in non‐stick pans were found to significantly reduce emissions. OPC calibration factors varied between 1.5 and 5.0 showing that a single value cannot be used for all meals and that gravimetric sampling is necessary when measuring PM_2.5 concentrations in kitchens.     

Down-link OFDRMA communications

Wireless Networks - Orthogonal frequency-division multiplexing with random multiple access (OFDRMA) is discussed for down-link communications, whereby a single base-station transmits information...