Simulation of producer gas flameless combustion with fresh reactant diluted by hot flue gas

Flameless combustion is considered as a flexible and efficient combustion process for low heating value gas fuel. This paper presents numerical simulations of premixed flameless combustion using producer gas as a fuel. Different initial conditions of the premixed fresh reactant (air/fuel mixture) and dilution levels are taken into account for the investigation. The numerical simulations were investigated using a network of chemical reactor models with the detailed reaction mechanism of GRI‐Mech 3.0. A threshold dilution level for flameless combustion fuelled by producer gas was determined. The numerical results show that dilution of the fresh reactant with hot combustion products and initial fresh reactant temperature play important roles in flameless combustion formation and its auto‐ignition behaviour, rather than equivalence ratio of the fresh reactant. In the flameless combustion regime, temperature and chemical concentrations were reduced while chemical kinetics process was decelerated, resulting in delay of the auto‐ignition process.     

Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Analysis of indoor PM2.5 exposure in Asian countries using time use survey

Most household fuels used in Asian countries are solid fuels such as coal and biomass (firewood, crop residue and animal dung). The particulate matter (PM), CO, NOx and SOx produced through the combustion of these fuels inside the residence for cooking and heating has an adverse impact on people's health. PM 2.5 in particular, consisting of particles with an aerodynamic diameter of 2.5 μm or less, penetrates deep into the lungs and causes respiratory system and circulatory system diseases and so on. As a result, the World Health Organization (WHO) established guideline values for this type of particulate matter in 2005. In this study, the authors focused on PM 2.5 and estimated indoor exposure concentrations for PM 2.5 in 15 Asian countries. For each environment used for cooking, eating, heating and illumination in which people are present temporarily (microenvironment), exposure concentrations were estimated for individual cohorts categorized according to sex, age and occupation status. To establish the residence time in each microenvironment for each of the cohorts, data from time use surveys conducted in individual countries were used. China had the highest estimate for average exposure concentration in microenvironment used for cooking at 427.5 μg/m³ , followed by Nepal, Laos and India at 285.2 μg/m³, 266.3 μg/m³ and 205.7 μg/m³ , respectively. The study found that, in each country, the PM2.5 exposure concentration was highest for children and unemployed women between the ages of 35 and 64. The study also found that the exposure concentration for individual cohorts in each country was greatly affected by people's use of time indoors. Because differences in individual daily life activities were reflected in the use of time and linked to an assessment of exposure to indoor air-polluting substances, the study enabled detailed assessment of the impact of exposure.     

中、日、欧的被试者对河川景观注视过程的比较研究

在景观认知·评价过程中,如果把眼球运动作为反映大脑所进行的视觉情报处理过程的外部参数,那么眼的运动方式就可能因评价者的生活经验、知识水平甚至价值观和思维方式的不同而产生差异。因此,可以设想被试者的社会文化背景的差异也有可能会从他们对景观的认知方式上得到体现。作为视觉认知中异域文化差异的比较研究之一,运用眼球运动跟踪仪对评价者的景观认知评价过程进行了跟踪测试,并试图通过对认知过程中的注视点分布、注视点数以及注视点的停留时间和注视内容的变化趋势这几个角度的分析比较来探讨社会文化背景的差异如何体现在人类视觉情报信息的收集整理的外部反应中,从而明确在地域特色景观的保留和营造上构成要素的布局方式的意义。     

Effects of SO2 on selective catalytic reduction of NO with NH3 over a TiO2 photocatalyst

The effect of SO₂ gas was investigated on the activity of the photo-assisted selective catalytic reduction of nitrogen monoxide (NO) with ammonia (NH₃) over a TiO₂ photocatalyst in the presence of excess oxygen (photo-SCR). The introduction of SO₂ (300 ppm) greatly decreased the activity of the photo-SCR at 373 K. The increment of the reaction temperature enhanced the resistance to SO₂ gas, and at 553 K the conversion of NO was stable for at least 300 min of the reaction. X-ray diffraction, FTIR spectroscopy, thermogravimetry and differential thermal analysis, x-ray photoelectron spectroscopy (XPS), elemental analysis and N₂ adsorption measurement revealed that the ammonium sulfate species were generated after the reaction. There was a strong negative correlation between the deposition amount of the ammonium sulfate species and the specific surface area. Based on the above relationship, we concluded that the deposition of the ammonium sulfate species decreased the specific surface area by plugging the pore structure of the catalyst, and the decrease of the specific surface area resulted in the deactivation of the catalyst.     

Thermal Spray Using a High-Frequency Pulse Detonation Combustor Operated in the Liquid-Purge Mode

Experiments on thermal spray by pulsed detonations at 150 Hz were conducted. Two types of pulse detonation combustors were used, one operated in the inert gas purge (GAP) mode and the other in the liquid-purge (LIP) mode. In both modes, all gases were supplied in the valveless mode. The GAP mode is free of moving components, although the explosive mixture is unavoidably diluted with the inert gas used for the purge of the hot burned gas. In the LIP mode, pure fuel-oxygen combustion can be realized, although a liquid-droplet injector must be actuated cyclically. The objective of this work was to demonstrate a higher spraying temperature in the LIP mode. First, the temperature of CoNiCrAlY particles heated by pulsed detonations was measured. As a result, the spraying temperature in the LIP mode was higher than that in the GAP mode by about 1000 K. Second, the temperature of yttria-stabilized zirconia (YSZ) particles, whose melting point was almost 2800 °C, heated by pulsed detonations in the LIP mode was measured. As a result, the YSZ particles were heated up to about 2500 °C. Finally, a thermal spray experiment using YSZ particles was conducted, and a coating with low porosity was successfully deposited.     

Material performance of age-hardened beryllium–copper alloy,CDA-C17200, in a high-pressure,gaseous hydrogen environment

In order to develop safer and more energy-efficient, hydrogen pre-cooling systems for use in hydrogen refueling stations, it is necessary to identify a high-strength metallic material with greater thermal conductivity and lower susceptibility to hydrogen embrittlement, as compared with ordinary, stable austenitic stainless steels. To accomplish this task, the hydrogen compatibility of a precipitation-hardened, high-strength, copper-based alloy was investigated by slow-strain-rate tensile (SSRT), fatigue-life, fatigue-crack-growth (FCG) and fracture toughness tests in 115-MPa hydrogen gas at room temperature. The hydrogen solubility and diffusivity of the alloy were also determined. The hydrogen solubility of the alloy was two or three orders of magnitude lower than that of austenitic stainless steels. The alloy also demonstrated absolutely no hydrogen-induced degradation of its strength properties, a factor which could contribute to the reduction of costs related to the construction and maintenance of hydrogen refueling stations, owing to the downsizing and improved cooling performance of the pre-cooling systems.     

Threshold stress intensity factor for hydrogen-assisted cracking of CR-MO steel used as stationary storage buffer of a hydrogen refueling station

In order to determine appropriate value for threshold stress intensity factor for hydrogen-assisted cracking (K_IH), constant-displacement and rising-load tests were conducted in high-pressure hydrogen gas for JIS-SCM435 low alloy steel (Cr-Mo steel) used as stationary storage buffer of a hydrogen refuelling station with 0.2% proof strength and ultimate tensile strength equal to 772 MPa and 948 MPa respectively. Thresholds for crack arrest under constant displacement and for crack initiation under rising load were identified. The crack arrest threshold under constant displacement was 44.3 MPa m^1/2 to 44.5 MPa m^1/2 when small-scale yielding and plane-strain criteria were satisfied and the crack initiation threshold under rising load was 33.1 MPa m^1/2 to 41.1 MPa m^1/2 in 115 MPa hydrogen gas. The crack arrest threshold was roughly equivalent to the crack initiation threshold although the crack initiation threshold showed slightly more conservative values. It was considered that both test methods could be suitable to determine appropriate value for K_IH for this material.