Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

Microstructure and mechanical behavior of laser aided additive manufactured low carbon interstitial Fe49.5Mn30Co10Cr10C0.5 multicomponent alloy

Laser aided additive manufacturing(LAAM)was used to fabricate bulk Fe49.5Mn30Co10Cr10C0.5 interstitial multicomponent alloy using pre-alloyed powder.The room temperature yield strength(σy),ultimate tensile strength(σUTS)and elongation(εUST)were 645 MPa,917 MPa and 27.0％respectively.The as-built sample consisted of equiaxed and dendritic cellular structures formed by elemental segregation.These cellular structures together with oxide particle inclusions were deemed to strengthen the material.The other contributing components include dislocation strengthening,friction stress and grain bound-ary strengthening.The high εUTS was attributed to dislocation motion and activation of both twinning and transformation-induced plasticity(TWIP and TRIP).Tensile tests performed at-40℃and-130℃demonstrated superior tensile strength of 1041 MPa and 1267 MPa respectively.However,almost no twinning was observed in the fractured sample tested at-40℃and-130℃.Instead,higher fraction of strain-induced hexagonal close-packed(HCP)ε phase transformation of 21.2％were observed for fractured sample tested at-40℃,compared with 6.3％in fractured room temperature sample.     

Targeted Delivery of Anesthetic Agents to Bone Tissues using Conductive Microneedles Enhanced Iontophoresis for Painless Dental Anesthesia

Pain management during dental procedures is a cornerstone for successful daily practice. In current practice, the traditional needle and syringe injection is used to administer local anesthesia. However, the appearance of long needles and the pain associated with it often leads to dental anxiety deterring timely interventions. Microneedles (MNs) have emerged as a minimally invasive alternative to hypodermic needles and shown to be effective in transdermal drug delivery applications. In this article, the potential use of MNs for local anesthesia delivery in dentistry is explored. The development of a novel conductive MN array that can be used in combination with iontophoresis technique to achieve drug penetration through the oral mucosa and the underlying bone tissue is presented. The conductive MN array plays a dual-role, creating micro-conduits and lowering the resistance of the oral mucosa. The reduced tissue resistance further enhances the application of a low-voltage current that is able to direct and accelerate the drug molecules to target the sensory nerves supplying teeth. The successful delivery of lidocaine using this new strategy in a clinically relevant rabbit incisor model is shown to be as effective as the current gold standard.     

Poly(lactide)/cellulose nanocrystal nanocomposites by high-shear mixing

There is currently considerable interest in developing stiff, strong, tough, and heat resistant poly(lactide) (PLA) based materials with improved melt elasticity in response to the increasing demand for sustainable plastics. However, simultaneous optimization of stiffness, strength, and toughness is a challenge for any material, and commercial PLA is well-known to be inherently brittle and temperature-sensitive and to show poor melt elasticity. In this study, we report that high-shear mixing with cellulose nanocrystals (CNC) leads to significant improvements in the toughness, heat resistance, and melt elasticity of PLA while further enhancing its already outstanding room temperature stiffness and strength. This is evidenced by (i) one-fold increase in the elastic modulus (6.48 GPa), (ii) 43% increase in the tensile strength (87.1 MPa), (iii) one-fold increase in the strain at break (∼6%), (iv) two-fold increase in the impact strength (44.2 kJ/m²), (v) 113-fold increase in the storage modulus at 90°C (787.8 MPa), and (vi) 10³-fold increase in the melt elasticity at 190°C and 1 rad/s (∼10⁵ Pa) via the addition of 30 wt% CNC. It is hence possible to produce industrially viable, stiff, strong, tough, and heat resistant green materials with improved melt elasticity through high-shear mixing.     

Photoluminescence of Gallate Glass-Ceramics: Al2O3 Influence

Glass and Ceramics - The influence of Al2O3 as an additive and the heat-treatment regime on the luminescence spectra of gallate glass-ceramics was investigated. It is shown that its luminescence...     

Single Cell Bioprinting with Ultrashort Laser Pulses

Tissue engineering requires the precise positioning of mammalian cells and biomaterials on substrate surfaces or in preprocessed scaffolds. Although the development of 2D and 3D bioprinting technologies has made substantial progress in recent years, precise, cell-friendly, easy to use, and fast technologies for selecting and positioning mammalian cells with single cell precision are still in need. A new laser-based bioprinting approach is therefore presented, which allows the selection of individual cells from complex cell mixtures based on morphology or fluorescence and their transfer onto a 2D target substrate or a preprocessed 3D scaffold with single cell precision and high cell viability (93–99% cell survival, depending on cell type and substrate). In addition to precise cell positioning, this approach can also be used for the generation of 3D structures by transferring and depositing multiple hydrogel droplets. By further automating and combining this approach with other 3D printing technologies, such as two-photon stereolithography, it has a high potential of becoming a fast and versatile technology for the 2D and 3D bioprinting of mammalian cells with single cell resolution.     

Quantum-Confinement Effect in Silicon Nanocrystals during Their Dissolution in Model Biological Fluids

Semiconductors - In present work, we studied the mechanisms of dissolution of porous silicon nanoparticles (PSi NPs) during their incubation in model liquids, i.e. water and phosphate buffered...     

Effect of TiB on the local texture of α phases in titanium matrix composites

Journal of Materials Science - The crystallographic orientation of TiB is one of the main factors that influence the microstructure and texture evolution of Ti-TiB composites. Different...     

Phenomenon of Reduction in Friction at the Toe of Gravity Landslide under Seismic Vibration Effect

Journal of Mining Science - The article describes the lab-scale testing of dynamic instability in a block placed on a rough slope surface and subjected to small-amplitude vibrations. It is shown...