Experimentelle Untersuchung des Abwälzverhaltens von Beveloidverzahnungen mit lokal angepassten Verzahnungsdaten entlang der Zahnbreite

Forschung im Ingenieurwesen - Zur Übertragung von Drehmoment und Drehzahl in beliebiger Achsanordnung eignen sich bei kleinem Achswinkel bis 30° Beveloidverzahnungen. Besonders...     

Profiling hot isostatically pressed canister–wasteform interaction for Pu-bearing zirconolite-rich wasteforms

Zirconolite-rich full ceramic wasteforms designed to immobilize Pu-bearing wastes were produced via hot isostatic pressing (HIP) using stainless steel (SS) and nickel (Ni) HIP canisters. A detailed profiling of the elemental compositions of the major and minor phases over the canister–wasteform interaction zone was performed using scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (SEM-EDS) characterization. Bulk sample analyses from regions near the center of the HIP canister were also conducted for both samples using X-ray diffraction and SEM-EDS. The sample with the Ni HIP canister showed almost no interaction zone with only minor diffusion of Ni from the inner wall of the canister into the near-surface region of the wasteform. The sample with the SS HIP canister showed ∼100–120 μm of interaction zone dominated by high-temperature Cr diffusion from canister materials to the wasteform with the Cr predominantly incorporated into the durable zirconolite phase. We also examined, for the first time, changes to the HIP canister wall thickness caused by HIPing and demonstrated that no canister wall thinning occurred. Instead, in the areas examined, the canister wall thickness was observed to increase (up to ∼20%) due to the compression occurring during the HIP cycle. Further, only sparse formation of (Cr, Mn)-rich oxide particles were noted within the HIP canister inner wall area immediately adjacent to the ceramic material, with no evidence for reverse diffusion of ceramic materials. Though the HIP canister–wasteform interaction extends to ∼120 μm when using an SS HIP canister for the system investigated, this translates to <<1 vol.% for an industrial scale HIPed wasteform. Importantly, the HIP canister–wasteform interactions did not produce any obviously less durable phases in the wasteform or had any detrimental impact on the HIP canister properties.     

Live video streaming service with pay-as-you-use model on Ethereum Blockchain and InterPlanetary file system

Wireless Networks - In centralized video streaming platforms, the platform owner, rather than the content producer, controls most of the content uploaded on the centralized video...     

Stable Light-Emitting Electrochemical Cells Using Hyperbranched Polymer Electrolyte

The choice of an adequate electrolyte is a fundamental aspect in polymer light-emitting electrochemical cells (PLECs) as it provides the in situ electrochemical doping and influences the performance of these devices. In this study, a hyperbranched polymer (Hybrane DEO750 8500) blended with a Li salt is used as a novel electrolyte in state-of-the-art Super Yellow (a polyphenylenevinylene) based LECs. Due to the desirable properties of the hyperbranched polymer and the homogeneous and smooth films that it forms with the emitting polymer, PLEC with excellent electroluminescent properties are obtained using a pulsed current bias scheme. The devices are very stable, with lifetimes in excess of 2000 h with initial luminance values above 450 cd m⁻², a peak efficiency of 12.6 lm W⁻¹, and sub-minute turn-on times. The stability of the devices is also studied by measuring the photoluminescence (PL) of the semiconductor during electroluminescent operation. The findings suggest that it is possible to observe the quenching of the PL in vertically stacked devices due to the advancement of the doped fronts in the film and an immediate PL recovery when the bias is removed.     

Nanocomposite powders of hydroxyapatite-graphene oxide for biological applications

The repair of bone fractures is a clinical challenge for patients with impaired healing, such as osteoporosis. Currently, different strategies have been developed to design new biomaterials, enhancing their interactions with biological systems and conducting the cellular behavior in the desired direction to help fracture healing. In the present work, hydroxyapatite-graphene oxide (HA-GO) nanocomposites were produced and the morphological and physicochemical influences of the addition of 0.5 wt%, 1.0 wt% and 1.5 wt% of GO to HA were observed. FEG-SEM and TEM analyses of HA-GO nanocomposites showed HA nanoparticles adhered to the surface of the GO sheets, suggesting an effective method to form nanostructured graphene-based biomaterials. As confirmation, physicochemical analyses by Raman, FTIR and TGA demonstrated a strong affinity between HA and GO, according to the increase of concentration from 0.5 wt% to 1.5 wt% GO in the HA-GO nanocomposites. Also, in order to evaluate the HA-GO nanocomposites behavior under biological microenvironment, in vitro bioactivity and indirect cytotoxicity tests were performed. FEG-SEM analyses confirmed the positive results for the bioactivity properties of HA-GO nanocomposite and indirect cytotoxicity demonstrated that even with a decrease in the hDPSCs viability and proliferation, when increasing to 1.5 wt% of GO concentration, high level of cell viability was exhibited by HA-GO nanocomposites. These biological results suggested the 0.5 wt% HA-GO nanocomposite as a potential bioactive bone graft and a promising biomaterial for bone tissue regeneration, when compared to the pure HA.     

Nido-Hydroborate-Based Electrolytes for All-Solid-State Lithium Batteries

Hydroborate-based solid electrolytes have recently been successfully employed in high voltage, room temperature all-solid-state sodium batteries. The transfer to analogous lithium systems has failed up to now due to the lower conductivity of the corresponding lithium compounds and their high cost. Here LiB₁₁H₁₄ nido-hydroborate as a cost-effective building block and its high-purity synthesis is introduced. The crystal structures of anhydrous LiB₁₁H₁₄ as well as of LiB₁₁H₁₄-based mixed-anion solid electrolytes are solved and high ionic conductivities of 1.1 × 10⁻⁴ S cm⁻¹ for Li₂(B₁₁H₁₄)(CB₁₁H₁₂) and 1.1 × 10⁻³ S cm⁻¹ for Li₃(B₁₁H₁₄)(CB₉H₁₀)₂ are obtained, respectively. LiB₁₁H₁₄ exhibits an oxidative stability limit of 2.6 V versus Li⁺/Li and the proposed decomposition products are discussed based on density functional theory calculations. Strategies are discussed to improve the stability of these compounds by modifying the chemical structure of the nido-hydroborate cage. Galvanostatic cycling in symmetric cells with two lithium metal electrodes shows a small overpotential increase from 22.5 to 30 mV after 620 h (up to 0.5 mAh cm⁻²), demonstrating that the electrolyte is compatible with metallic anodes. Finally, the Li₂(B₁₁H₁₄)(CB₁₁H₁₂)  electrolyte is employed in a proof-of-concept half cell with a TiS₂ cathode with a capacity retention of 82% after 150 cycles at C/5.     

An automated treatment planning strategy for highly noncoplanar radiotherapy arc trajectories

Radiation therapy is a technology-driven cancer treatment modality that has experienced significant advances over the last decades, due to multidisciplinary contributions that include engineering and computing. Recent technological developments allow the use of noncoplanar volumetric modulated arc therapy (VMAT), one of the most recent photon treatment techniques, in clinical practice. In this work, an automated noncoplanar arc trajectory optimization framework designed in two modular phases is presented. First, a noncoplanar beam angle optimization algorithm is used to obtain a set of noncoplanar irradiation directions. Then, anchored in these directions, an optimization strategy is proposed to compute an optimal arc trajectory. The computational experiments considered a pool of twelve difficult head-and-neck tumor cases. It was possible to observe that, for some of these cases, the optimized noncoplanar arc trajectories led to significant treatment planning quality improvements, when compared with coplanar VMAT treatment plans. Although these experiments were done in a research environment treatment planning software (matRad), the conclusions can be of interest for a clinical setting: automated procedures can simplify the current treatment workflow, produce high-quality treatment plans, making better use of human resources and allowing for unbiased comparisons between different treatment techniques.     

Resistance variation of conductive ink applied by the screen printing technique on different substrates

This research study focuses on the application of conductive ink by the screen printing technique to evaluate the potential of creating printed electrodes and to investigate the effect of washing upon electrical resistance and flexibility. Two conductive inks were applied by a conventional screen printing method on four different textile substrates, 100% cotton, 50%/50% cotton/polyester, 100% polyester and 100% polyamide. The inks were also applied on a multifibre fabric. Atmospheric plasma treatment was applied to improve the adhesion to the samples, and the resistance values were compared with those of non‐treated samples. The values were measured before and after cleaning and washing tests, which were performed to simulate domestic treatment for garments to predict the behaviour of the inks after normal usage of the fabrics. Comfort properties like stiffness of the fabrics were also evaluated after five and 10 washing cycles. It was observed that PE 825 ink forms a thicker film on the fabric surface, contributing to the loss of flexibility of the textile. However, PE 825 ink also produced the best results in terms of durability and lower values of resistance. Polyamide fabrics lost their conductive property after five washing cycles due to weak bonding between the ink and the fibres, whereas cotton fibres provided the best results.