A novel ceramic matrix composite based on YNbO4–TiO2 for microwave applications

This work presents the dielectric properties of YNbO₄ (YNO)–TiO₂ composites in the microwave range. X-ray diffraction analysis demonstrates that the addition of TiO₂ to YNO results in the formation of a Y(Nb_0.5Ti_0.5)₂O₆ phase. In the microwave range, the values of permittivity and dielectric loss did not present major changes with the increment of TiO₂. Moreover, the addition of TiO₂ results in an improvement in the thermal stability of YNO, with YNO63 demonstrating a resonant frequency of ?8.96 ppm.°C^?1. We utilised numerical simulations to evaluate the behaviour of these materials as dielectric resonator antennae and it is found that they exhibit a reflection coefficient below ?10 dB at the resonant frequency, with a realised gain of 4.94 – 5.76 dBi, a bandwidth of 665–1050 MHz and a radiation efficiency above 84%. Our results indicate that YNO–TiO₂ composites are interesting candidates for microwave operating devices.     

Increasing the photocatalytic and fungicide activities of Ag3PO4 microcrystals under visible-light irradiation

The present study reports for the first time the performance of silver phosphate (Ag₃PO₄) microcrystals as photocatalyst (degradation of Rodamine B-RhB) and antifungal agent (against Candida albicans–C. albicans) under visible-light irradiation (455 nm). Ag₃PO₄ microcrystals were synthesized by a simple co-precipitation (CP) method at room temperature. The structural and electronic properties of the as-synthetized Ag₃PO₄ have been investigated before and after 4 cycles of RhB degradation under visible light using X-ray diffraction (XRD), micro-Raman spectroscopy, UV–Vis spectrophotometer and field emission scanning electron microscopy (FE-SEM) images. The antifungal activity was analyzed in planktonic cells and 48h-biofilm of C. albicans by colony forming units (CFU) counting, confocal laser and FE-SE microscopies. Statistical analysis was carried out using SPSS software. Morphological and structural modifications of Ag₃PO₄ were observed upon recycling. After 4 recycles, the material maintained its photodegradation property; an eightfold increase in the efficiency of Ag₃PO₄ was observed in planktonic cells and a two fold increase in biofilm when irradiated under visible light. Thus, higher antifungal effectiveness against C. albicans was obtained when associated with visible-light irradiation.     

Development of low-alcohol isotonic beer by interrupted fermentation

Alcohol-free beer with isotonic properties is getting more popular and its production can be carried out by different production strategies; however, interrupted fermentation is still a challenge. Therefore, the objective of this study was to develop a low-alcohol isotonic beer (<0.5% v/v) by interrupted fermentation. Moreover, the major objective is to compare the developed product to commercial beverages (sports drinks, ‘Pilsen' regular beer, alcohol-free beers and low-alcohol isotonic beer). The beverages were evaluated based on pH, alcohol content (% v/v), total titratable acidity (mEq L⁻¹), osmolality (mOsmol kg⁻¹), bitterness International Bitterness Units, colour European Brewery Convention, total phenolic compounds (mg L⁻¹ gallic acid), reducing and total sugars (%) and Na and K contents (mg L⁻¹). The developed low-alcohol isotonic beer presented characteristics similar to sports drinks, with the advantage of being richer in phenolic compounds and suitable osmolality. Despite salts were added in its formulation, the grades attributed to all beers employed in the sensory evaluation, as well as the purchase intention did not present significant differences.     

Dielectric relaxation of vegetable-based polyurethane

Vegetable-based polyurethane (PU) was prepared in the thin film form by spin coating. This polymer is synthesised from castor oil, which can be extracted from the seeds of a native plant in Brazil called mamona. This polymer is biocompatible and is being used as material for artificial bone. The PU was characterised by dielectric spectroscopy in a wide range of frequency (10^–5 Hz to 10⁵ Hz) and by thermally stimulated discharge current (TSDC) measurements. The glass transition temperature (T _g = 39°C) was determined and using the initial rise method the activation energy was found to be 1.58 eV.     

Characterization of the Residence Time Distribution in Spray Dryers

In this work it is presented a study on the residence time distribution (RTD) of particles in a co-current pilot-plant spray dryer operated with a rotary atomization system. A nuclear technique is applied to investigate the RTD responses of spray dryers. The methodology is based on the injection of a radioisotope tracer in the feed stream followed by the monitoring of its concentration at the outlet stream. The experiments were performed during the drying of aqueous suspensions of gadolinium oxide. The RTD responses obtained experimentally presented good reproducibility, indicating that the technique applied is well suited to investigating fluid-dynamics of spray dryers. In addition to the experimental investigation, a mathematical model was used to describe the RTD experimental curves.     

Synthesis and physicochemical characterization of a well-defined poly(butadiene 1,3)-block-poly(dimethylsiloxane) copolymer

For the first time, order-order and order-disorder transitions were detected and characterized in a model diblock copolymer of poly(butadiene-1,3) and poly(dimethylsiloxane) (PB-b-PDMS). This model PB-b-PDMS copolymer was synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene 1,3 (B) and hexamethylciclotrisiloxane (D₃), and subsequently characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size exclusion chromatography (SEC), Fourier Transform infrared spectroscopy (FTIR), Small-Angle X-ray scattering (SAXS) and rheology. SAXS combined with rheological experiments shows that the order-order and order-disorder transitions are thermoreversible. This fact indicates that the copolymer has sufficient mobility at the timescale and at the temperatures of interest to reach their equilibrium morphologies.     

Node and element resequencing using the Laplacian of a finite element graph: Part I—General concepts and algorithm

A Finite Element Graph (FEG) is defined here as a nodal graph (G), a dual graph (G*), or a communication graph (G˙) associated with a generic finite element mesh. The Laplacian matrix ( L (G), L (G*) or L (G˙)), used for the study of spectral properties of an FEG, is constructed from usual vertex and edge connectivities of a graph. An automatic algorithm, based on spectral properties of an FEG (G, G* or G˙), is proposed to reorder the nodes and/or elements of the associated finite element mesh. The new algorithm is called Spectral PEG Resequencing (SFR). This algorithm uses global information in the graph, it does not depend on a pseudoperipheral vertex in the resequencing process, and it does not use any kind of level structure of the graph. Moreover, the SFR algorithm is of special advantage in computing environments with vector and parallel processing capabilities. Nodes or elements in the mesh can be reordered depending on the use of an adequate graph representation associated with the mesh. If G is used, then the nodes in the mesh are properly reordered for achieving profile and wavefront reduction of the finite element stiffness matrix. If either G* or G˙ is used, then the elements in the mesh are suitably reordered for a finite element frontai solver, A unified approach involving FEGs and finite element concepts is presented. Conclusions are inferred and possible extensions of this research are pointed out. In Part II of this work,¹ the computational implementation of the SFR algorithm is described and several numerical examples are presented. The examples emphasize important theoretical, numerical and practical aspects of the new resequencing method.     

Screening of supports for the immobilization of pectinmethylesterase from acerola (Malpighia glabra L)

A partially purified extract of pectinmethylesterase (PME) from acerola fruit was immobilized on various supports: glass, celite, chrysotile, agarose, concanavalin A Sepharose 4B, egg shell, polyacrylamide and gelatin. In addition, reticulation with glutaraldehyde was assessed, as well as the use of gelatin in the presence of celite, glass and silica. The highest immobilization yields were obtained when the pectinmethylesterase was immobilized in concanavalin A Sepharose 4B (81.7%) and in gelatin‐water (78.0%). Copyright © 2004 Society of Chemical Industry