Synthesis, spark plasma sintering and electrical conduction mechanism in BaTiO3-Cu composites

BaTiO₃-Cu composite powders were prepared via an alkoxide-mediated synthesis approach. As-synthesized BaTiO₃ nanoparticles were as small as 40 nm and coated partially larger Cu particles of approximately 1 μm in size. Thermogravimetric analysis (TGA) and dilatometry revealed a gradual increase in weight loss and retarded shrinkage with the increase of Cu addition. BaTiO₃-Cu composites were successfully densified by spark plasma sintering (SPS). The microstructures show an average grain-size for BaTiO₃ of around 100 nm and a crystallite size of about 1 μm for the Cu inclusions. The AC conductivity of the BaTiO₃-Cu composites increased with increasing Cu content or with temperature. The dominant electrical conduction mechanism in SPSed BaTiO₃-Cu composites changed from migration of oxygen vacancies to band conduction of trapped electrons in oxygen vacancies with the increase of Cu content.     

Building micro and nanosystems with electrochemical discharges

Since the discovery of the electrochemical discharge phenomenon by Fizeau and Foucault, several contributions have expanded the wide range of applications associated with this high current density electrochemical process. The complexity of the phenomenon, from the macroscopic to the microscopic scales, led since then to experimental and theoretical studies from different research fields. This contribution reviews the chemical and electrochemical perspectives where a mechanistic model based on results from radiation chemistry of aqueous solutions is proposed. In addition applications to micro-machining and fabrication of nanoparticles are discussed.     

Static and dynamic mechanical properties of boron carbide processed by spark plasma sintering

Spark plasma sintering (SPS) has become a popular technique for the densification of covalent ceramics. The present investigation is focused on the static mechanical properties and dynamic compressive behavior of SPS consolidated boron carbide powder without any sintering additives. Fully dense boron carbide bodies were obtained by a short high temperature SPS treatment. The mechanical properties of the SPS-processed material, namely hardness (32 GPa), Young modulus (470 GPa), fracture toughness K_C (3.9–4.9 MPa m^0.5), flexural strength (430 MPa) and Hugoniot elastic limit (17–19 GPa) are close or even better than those of hot-pressed boron carbide.     

Simultaneous synthesis and densification of transparent,photoluminescent polycrystalline YAG by current activated pressure assisted densification (CAPAD)

We report a method for the synthesis and processing of transparent bulk polycrystalline yttrium aluminum garnet (YAG) and photoluminescent Ce-doped YAG ceramics via solid-state reactive-current activated pressure assisted densification (CAPAD). The process uses commercially available γ-Al₂O₃, Y₂O₃, and CeO₂ nanopowders. The nanopowders were reacted and densified simultaneously at temperatures between 850 °C and 1550 °C and at a maximum pressure of 105 MPa. The solid-state reaction to phase pure YAG occurs in under 4 min at processing temperatures 1100 °C which is significantly faster (on the order of tens of hours) and occurs at much lower temperatures (∼600 °C) compared to conventional reaction sintering. We found that the reaction significantly improves densification – the shrinkage rate of reaction-produced YAG was three times higher than that of YAG using pre-reacted powder. The Ce additions were found to retard the reaction driven shrinkage kinetics by a factor ∼3, but are still faster (by a factor ∼1.6) than those associated with direct densification (no synthesis). Densities >99% were achieved in both pure YAG and Ce doped YAG (Ce:YAG). Results of optical measurements show good transparency in the visible and photoluminescence (PL) in the Ce:YAG. The PL peak is broad and appears white when excited using blue light confirming that the ceramics can be used in solid state lighting to produce white light.     

Discharge studies in micromegas detectors in a 150 GeV/c pion beam

A detailed study of several Micromegas detectors prototyped for the COMPASS and CLAS12 experiments is presented. Using a 150 GeV/c pion beam, the discharge probability was measured for several detector variants including bulk and non-bulk Micromegas. A detector equipped with an additional GEM foil as pre-amplification stage was also tested. A resistive coating of the readout strips was found to reduce the amplitude of the discharge by at least two orders of magnitude which was below the detection limit of the experimental setup. The effects of the micro-mesh type and material were investigated as well as the influence of the drift gap. Response in the presence of a 1.5 T transverse magnetic field was also studied. The measurements presented were performed during a RD51 beam test period.     

Engine knock and combustion characteristics of a spark ignition engine operating with varying hydrogen and carbon monoxide proportions

Varying proportions of hydrogen and carbon monoxide (synthesis gas) have been investigated as a spark ignition (SI) engine fuel in this paper. It is important to understand how various synthesis gas compositions effect important SI combustion fundamentals, such as knock and burn duration, because in synthesis gas production applications, the compositions can vary significantly depending on the feedstock and production method.A single cylinder cooperative fuels research (CFR) engine was used to investigate the knock and combustion characteristics of three blends of synthesis gas (H₂/CO ratio); 1) 100/0, 2) 75/25, and 3) 50/50, by volume. These blends were tested at three compression ratios (6:1, 8:1, and 10:1), and three equivalence ratios (0.6, 0.7, and 0.8).It was revealed that the knock limited compression ratio (KLCR) of a H₂/CO mixture increases with increasing CO fraction, for a given spark timing. For a given equivalence ratio and spark timing, a 50%/50% H₂/CO mixture produced a KLCR of 8:1 compared to a 100% H₂ condition, which produced a KLCR of 6:1. The burn duration and ignition lag is also increased with increasing CO fraction. The results from this work are important for those considering using synthesis gas as a fuel in SI engines. It reveals that although CO is a slow burning fuel, higher CO fractions in synthesis gas can be beneficial, because of its increased resistance to knock, which gives it the potential of producing higher indicated efficiencies through the utilization of an engine with a higher compression ratio.     

Synthesis by Spark Plasma Sintering: A new way to obtain electrode materials for lithium ion batteries

In the search of high-performance materials for lithium ion batteries, Li₂CoPO₄F offers many advantages like high theoretical capacity and high operating potential. The synthesis of Li₂CoPO₄F has been reinvestigated considering a conventional solid state reaction and an unconventional way. Due to the long heat-treatments required by the conventional approach, a beginning of grains coalescence is observed. Limiting particles growth has been allowed by a shorter reaction done by SPS (Spark Plasma Sintering). By this method, the synthesis of Li₂CoPO₄F was greatly shortened (from 10 h to 9 min), which favours the getting of submicrometric particles. The comparison of the electrochemical properties of the Li₂CoPO₄F obtained by the different ways confirms the advantages of SPS synthesis in performance enhancement.     

Surface coating on carbon nanofibers with alumina precursor by different synthesis routes

Alumina-reinforced carbon nanofiber nanocomposites were prepared using different routes; powders mixture, colloidal route and sol-gel process followed by spark plasma sintering (SPS). CNFs/xAl₂O₃ (x = 10-50 vol.%) were prepared through nanopowders mixing in a high-energy attrition milling. The main limitations in the preparation of this kind of nanocomposites are related to the difficulty in obtaining materials with a homogeneous distribution of both phases and the different chemical nature of CNFs and Al₂O₃, which causes poor interaction between them. A surface coating of CNFs by wet chemical routes with an alumina precursor is proposed as a very effective way to improve the interaction between CNFs and Al₂O₃. An improvement of 50% in fracture strength was found for similar nanocomposite compositions when the surface coating was used. The improved mechanical properties of these nanocomposites are caused by stronger interaction between the CNFs and Al₂O₃.