干扰条件下的“北斗”信号解扩重构DOA估计

在干扰条件下，卫星导航抗干扰波束形成算法往往需要卫星信号波达方向（Direction-of-Arrival，DOA）的先验信息。但当存在低信噪比信号或主动干扰源时，常规的DOA估计算法性能急剧下降甚至失效。针对此问题，提出了一种被干扰信号压制的低信噪比“北斗”信号的DOA估计算法。该算法首先通过对接收信号进行子空间投影抑制干扰信号，然后对抑制干扰后的信号进行解扩重构处理，最后通过多重信号分类算法完成对“北斗”信号的DOA估计。仿真结果表明，在干扰信号干信比80 dB条件下，“北斗”信号DOA估计误差在5°以内，为下一步进行波束形成计算提供了高精度的入射角信息。     

基于信号增强的缓慢泄漏检测方法

目前管道泄漏检测方法可有效检测突发泄漏，对于缓慢泄漏则存在检测灵敏度低、定位不准确等问题。基于此，提出了一种基于信号增强的缓慢泄漏检测方法。通过信号压缩（抽取及移位）克服缓慢泄漏压力信号下降平缓的缺点；根据声波信号具有波形尖锐突出、对突发泄漏敏感的优点，通过建立以压力为输入、虚拟声波为输出的声波信号变送器模型，将压力信号转换为声波信号，克服了泄漏压力信号容易被淹没在管道压力波动及背景噪声中的缺点，实现了缓慢泄漏信号的增强；利用临近插值方法重构虚拟声波信号，基于延时互相关分析实现了缓慢泄漏的准确定位。实验结果表明，该方法具有显著的信号增强效果和定位精度，实现了缓慢泄漏的准确检测。     

水下图像处理技术研究综述

随着自主式水下机器人的发展，水下探测技术成为新的研究热点。然而，吸收效应和散射效应导致水下获取的图像存在雾化和色彩偏差等缺陷。降质的水下图像在一定程度上降低了水下目标识别的准确性。为了改善水下图像质量，国内外学者对水下图像处理方法进行了深入研究。因水下图像处理方法对提升水下目标识别准确性具有良好的促进作用，故其具有重要的研究与分析价值。介绍了水下成像模型，分析了水下图像视觉质量下降的原理；根据水下物理成像模型将水下图像处理方法分为水下图像增强与水下图像复原，并分别对两类方法的研究现状进行分析与归纳；最后，总结与讨论了各类方法的优缺点，并展望了未来的发展方向。     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。     

全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

Strain hardening behaviors and mechanisms of polyurethane under various strain rate loading

The uniaxial tension experiments are performed on thermoplastic polyurethane to investigate its mechanical behaviors and related potential mechanisms, and the loading strain rate is designing to be wide ranging from 0.0001 to 1 s⁻¹. It is found that the polyurethane presents an obvious rate-dependence, and the stress strain curves share distinct strain hardening characteristics under the investigated strain rates. Furthermore, the strain hardening ratios are sharing nearly same trends and appear to be influenced by both strain rate and the induced adiabatic heating. Besides, the ratio is also strain-dependent on previous loading history. Then, a two-dimension unit cell model is built to investigate potential equivalent mechanisms, of which the hard phase as inclusion is equivalent with crystallization zone, crosslinking sites, and so forth. The simulation results facilitate to explain the distinct strain hardening ratios, even for the matrix from the extrapolated curves under super-low strain rate loading. Finally, the analogic mechanisms of equivalent hard inclusions are proposed, which can reasonably explain the strain rate- and strain-dependence characteristics of polyurethane mechanical behaviors.     

Study of metal assisted anisotropic chemical etching of silicon for high aspect ratio in crystalline silicon solar cells

Textured surface is commonly used to enhance the efficiency of silicon solar cells by reducing the overall reflectance and improving the light scattering. In this study, a comparison between isotropic and anisotropic etching methods was investigated. The deep funnel shaped structures with high aspect ratio are proposed for better light trapping with low reflectance in crystalline silicon solar cells. The anisotropic metal assisted chemical etching (MACE) was used to form the funnel shaped structures with various aspect ratios. The funnel shaped structures showed an average reflectance of 14.75% while it was 15.77% for the pillar shaped structures. The average reflectance was further reduced to 9.49% using deep funnel shaped structures with an aspect ratio of 1:1.18. The deep funnel shaped structures with high aspect ratios can be employed for high performance of crystalline silicon solar cells.     

气液螺旋环状流压降特性研究

考虑旋流衰减的影响，对气液螺旋环状流的压降特性进行研究并推导出了螺旋环状流压降预测模型。定义压降旋-直比系数为气液两相螺旋环状流和气液两相直流的压降之比，以此来表征旋流衰减对压降的影响。基于量纲分析的方法对压降旋-直比系数进行分析，推导出其表达式，压降旋-直比系数依赖于Lockhart-Martinelli 参数和气相Froude数变化。最终，得出了气液两相螺旋环状流的压降预测模型。在50 mm内径的水平管内对螺旋环状流的压降特性进行了实验研究，其中气相表观流速变化范围为10~16 m/s，体积含液率（LVF）变化范围为0.6%~4.8%。通过与实验数据进行对比，压降预测模型的相对误差在±15%以内，为工程应用提供了参考。     

马尔可夫跳变线性系统最优控制的研究现状与进展

马尔可夫跳变线性系统（MJLS）是一种具有多个模态的随机系统，系统在各个模态之间的跳变转移由一组马尔可夫链来决定。MJLS模型因其在表示过程中可以产生突变而更能精确的描述实际工程应用中的系统。近年来，MJLS的最优控制问题成为了研究的热点，动态规划、极大值原理以及线性矩阵不等式等成为了解决此类问题的主流方法。本文对MJLS最优控制领域的研究现状进行了综述。分别对一般情况下、带有噪声的情况下、带有时滞的情况下以及某些特定情况下的MLJS最优控制问题的国内外研究现状进行论述。最后进行了总结并提出MJLS最优控制领域未来值得关注的研究方向。     

Rational Designs for Lithium-Sulfur Batteries with Low Electrolyte/Sulfur Ratio

Lithium-sulfur batteries (LSBs) are considered a promising next-generation energy storage device owing to their high theoretical energy density. However, their overall performance is limited by several critical issues such as lithium polysulfide (PS) shuttles, low sulfur utilization, and unstable Li metal anodes. Despite recent huge progress, the electrolyte/sulfur ratio (E/S) used is usually very high (≥20 µL mg⁻¹), which greatly reduces the practical energy density of devices. To push forward LSBs from the lab to the industry, considerable attention is devoted to reducing E/S while ensuring the electrochemical performance. To date, however, few reviews have comprehensively elucidated the possible strategies to achieve that purpose. In this review, recent advances in low E/S cathodes and anodes based on the issues resulting from low E/S and the corresponding solutions are summarized. These will be beneficial for a systematic understanding of the rational design ideas and research trends of low E/S LSBs. In particular, three strategies are proposed for cathodes: preventing PS formation/aggregation to avoid inadequate dissolution, designing multifunctional macroporous networks to address incomplete infiltration, and utilizing an imprison strategy to relieve the adsorption dependence on specific surface area. Finally, the challenges and future prospects for low E/S LSBs are discussed.