橡胶籽油制备生物柴油的工艺研究

实验研究了乙醇钠催化下橡胶籽油与乙醇进行酯交换反应制备生物柴油的工艺条件。通过正交实验和单因素实验,发现酯交换反应的最佳工艺条件:催化剂用量为油重的1.0%,醇油物质的量比为15∶1,反应温度为78℃,搅拌时间为120 min,在此反应条件下,橡胶籽油转化率为92.14%。     

小桐油制备生物柴油的研究

实验研究了以小桐子油为原料，采用循环气相酯化-酯交换-水蒸气蒸馏法制备生物柴油的工艺过程。着重研究了降低原料酸值以及酯交换过程的优化条件。试验结果表明。气相酯化法可在很短的时间内将原料的酸值降到酯交换对原料的酸值要求；酯交换反应的最佳操作条件为：甲醇用量为油重的20％，催化剂用量为油重的1％左右，反应温度为60—70℃，反应时间为90—120min。     

氨基磺酸非均相催化菜籽油及废油脂制备生物柴油

采用正交试验和单因素试验的方法研究了氨基磺酸催化菜籽油及废油脂与甲醇的酯交换过程,考察了醇油物质的量比、催化剂用量、反应温度和反应时间对反应收率的影响。结果表明:菜籽油酯交换的最佳反应条件为醇油物质的量比6∶1,氨基磺酸用量为原料油质量的1.0%,反应温度60℃,反应时间20 min,此工艺条件下,脂肪酸甲酯的收率达到95.6%;废油脂酯交换的最佳反应条件为醇油物质的量比8∶1,氨基磺酸用量为原料油质量的1.0%、反应温度65℃,反应时间30 min,此工艺条件下,脂肪酸甲酯的收率达到87.5%。利用红外光谱表征了菜籽油和生物柴油的结构,气相色谱分析了生物柴油的组成。     

麻疯果油预处理及酯交换制备生物柴油的试验研究

以热榨麻疯果油为原料,采用液体碱酯交换法制备生物柴油,研究了最佳的脱胶、脱酸及酯交换反应条件.试验结果表明,最佳脱胶工艺条件:温度为80℃、磷酸用量为原料油质量的0.2%、反应时间为30min、加水量为磷脂质量的3倍:最佳脱酸工艺条件:温度为85℃、超碱量为原料油质量的0.2%、搅拌速度为70r/min、反应时间为30min;最佳酯交换反应条件:甲醇:油=6:1(物质的量比)、催化剂(甲醇钠)用量为原料油质量的1.2%、反应温度为65℃、反应时间为20min,甲酯转化率可达94%以上,甲酯产品各项性能指标达到GB/T20828-2007要求.     

硫酸氢钠催化生物柴油合成反应的研究

以固体酸硫酸氢钠(NaHSO4·H20)为催化剂,以菜籽油和甲醇为反应物进行酯交换反应制备脂肪酸甲酯(生物柴油).采用正交实验考察了各因素对生物柴油产率的影响,得出最佳反应条件:反应温度为90℃,反应时间为12h,醇油物质的量比为40:1,催化剂用量为菜籽油质量的6%.极差顺序为温度、反应时间、醇油物质的量比、催化剂用量.     

花椒籽油生物柴油制备工艺研究

以花椒籽油为原料,对KOH催化其与甲醇发生酯交换反应制备生物柴油进行研究.采用物理萃取法降低花椒籽油中游离脂肪酸的含量,三次萃取后酸值达到2 mgKOH/g以下.研究了花椒籽油和甲醇在氢氧化钾催化下的酯交换反应.进行了不同醇油摩尔比、催化剂用量、反应时间、反应温度等反应条件下对产率的影响,得到最佳反应条件为醇油物质的量之比为12∶1,催化剂添加量为油脂质量的1.2％,反应温度为60 ～65℃,反应时间为45 min.     

花椒籽油生物柴油制备工艺研究

以花椒籽油为原料,对KOH催化其与甲醇发生酯交换反应制备生物柴油进行研究。采用物理萃取法降低花椒籽油中游离脂肪酸的含量,三次萃取后酸值达到2 mgKOH/g以下。研究了花椒籽油和甲醇在氢氧化钾催化下的酯交换反应。进行了不同醇油摩尔比、催化剂用量、反应时间、反应温度等反应条件下对产率的影响,得到最佳反应条件为醇油物质的量之比为12∶1,催化剂添加量为油脂质量的1.2%,反应温度为60～65℃,反应时间为45 min。     

SO42-/TiO2-ZrO2固体酸催化乌桕籽油制备生物柴油的研究

乌桕籽油是一种可再生的木本植物油料,可与甲醇发生酯交换反应制得生物柴油.试验表明,固体酸催化剂SO42-/TiO2-ZrO2对乌桕籽油酯交换反应表现出了较高的催化活性,当反应温度为150 ℃、醇油物质的量比为12:1、催化剂用量为乌桕籽油质量的5%、反应时间为6 h时,乌桕籽油的酯化率达到95%以上,催化剂重复和再生使用效果良好.同时,对该催化剂的SEM,TEM,XRD,BET结构表征表明,该催化剂表面呈多孔状,颗粒大小分布在10～100 nm,比表面积为114 m2/g,是一种纳米固体催化剂.     

棉籽酸化油酸催化两步法制备生物柴油的研究

以棉籽酸化油和甲醇为原料,采用酸催化两步法制备生物柴油.第一步为酸催化酯化和一次酯交换反应,第二步为酸催化二次酯交换反应.通过大量试验优化了反应条件:在酯化和一次酯交换阶段,醇油质量比为0.5:1,催化剂用量为棉籽酸化油质量的3%,反应温度为90℃,反应时间为150 min:在二次酯交换阶段,醇油质量比为0.7:1,催化剂用量为棉籽油质量的4%,反应时间为90min.在此条件下,生物柴油的产率达到94%以上,产品质量符合国家标准.     

磺酸型离子液体合成及催化制备生物柴油工艺研究

研究合成功能化酸性离子液体1-丙基磺酸-3-甲基咪唑硫酸氢盐([PrSO_3HMIm]HSO_4),采用核磁共振、红外光谱、热重分析等分析法进行表征验证,并用其催化菜籽油酯交换反应制备生物柴油,考察醇油物质的量之比、反应温度、反应时间和离子液体用量对酯交换反应的影响及离子液体的稳定性。结果表明:在n甲醇∶n菜籽油=10∶1,反应温度120℃,反应时间8 h,离子液体用量为菜籽油质量7%的条件下,生物柴油收率可达95.56%,且稳定性良好,循环使用5次催化性能未明显降低。     

Performance assessment of some ice TES systems

In this paper, a performance assessment of four main types of ice storage techniques for space cooling purposes, namely ice slurry systems, ice-on-coil systems (both internal and external melt), and encapsulated ice systems is conducted. A detailed analysis, coupled with a case study based on the literature data, follows. The ice making techniques are compared on the basis of energy and exergy performance criteria including charging, discharging and storage efficiencies, which make up the ice storage and retrieval process. Losses due to heat leakage and irreversibilities from entropy generation are included. A vapor-compression refrigeration cycle with R134a as the working fluid provides the cooling load, while the analysis is performed in both a full storage and partial storage process, with comparisons between these two. In the case of full storage, the energy efficiencies associated with the charging and discharging processes are well over 98% in all cases, while the exergy efficiencies ranged from 46% to 76% for the charging cycle and 18% to 24% for the discharging cycle. For the partial storage systems, all energy and exergy efficiencies were slightly less than that for full storage, due to the increasing effect wall heat leakage has on the decreased storage volume and load. The results show that energy analyses alone do not provide much useful insight into system behavior, since the vast majority of losses in all processes are a result of entropy generation which results from system irreversibilities.     

Effect of co-cultivation of Chlamydomonas reinhardtii with Azotobacter chroococcum on hydrogen production

Chlamydomonas reinhardtii cc124 and Azotobacter chroococcum bacteria were co-cultured with a series of volume ratios and under a variety of light densities to determine the optimal culture conditions and to investigate the mechanism by which co-cultivation improves H₂ yield. The results demonstrated that the optimal culture conditions for the highest H₂ production of the combined system were a 1:40 vol ratio of bacterial cultures to algal cultures under 200 μE m^?2 s^?1. Under these conditions, the maximal H₂ yield was 255 μmol mg^?1 Chl, which was approximately 15.9-fold of the control. The reasons for the improvement in H₂ yield included decreased O₂ content, enhanced algal growth, and increased H₂ase activity and starch content of the combined system.     

Exergetic evaluation of 5 biowastes-to-biofuels routes via gasification

This paper presents the exergy analysis results for the production of several biofuels, i.e., SNG (synthetic natural gas), methanol, Fischer–Tropsch fuels, hydrogen, as well as heat and electricity, from several biowastes generated in the Dutch province of Friesland, selected as one of the typical European regions. Biowastes have been classified in 5 virtual streams according to their ultimate and proximate analysis. All production chains have been modeled in Aspen Plus in order to analyze their technical performance. The common steps for all the production chains are: pre-treatment, gasification, gas cleaning, water–gas-shift reactions, catalytic reactors, final gas separation and upgrading. Optionally a gas turbine and steam turbines are used to produce heat and electricity from unconverted gas and heat removal, respectively. The results show that, in terms of mass conversion, methanol production seems to be the most efficient process for all the biowastes. SNG synthesis is preferred when exergetic efficiency is the objective parameter, but hydrogen process is more efficient when the performance is analyzed by means of the 1st Law of Thermodynamics. The main exergy losses account for the gasification section, except in the electricity and heat production chain, where the combined cycle is less efficient.     

液压系统常见的故障诊断及处理

任何工程机械式液压设备使用时出现故障是不可避免的。但是怎样确定故障的原因及找到好的解决方法，这是使用者最关心的问题。讲述了液压系统常见的故障及其排除方法。     

Economie d'énergie en trigénération

Trigeneration is defined as the production of three useful forms of energy—heat, cold and power—from a primary source of energy such as natural gas or oil. For instance, trigeneration systems typically produce electrical power via a reciprocating engine or gas turbine and recover a large percentage of the heat energy retained in the lubricating oil, exhaust gas and coolant water systems to maximize the utilization of the primary fuel. The heat produced can be totally or partially used to fuel absorption refrigerators. Therefore, trigeneration systems enjoy an inherently high efficiency and have the potential to significantly reduce the energy-related operation costs of facilities. In this paper, we describe a model of characterization of trigeneration systems trough the condition of primary energy saving and the quality index, compared to the separate production of heat, cold and power. The study highlights the importance of the choice of the separate production reference system on the level of primary energy saving and emissions reduction.     

Mineralogical characterization of the intraseam layers of Lofoi lignite deposits in Florina basin (western Makedonia,northwest Greece)

The mineralogical composition of intraseam layers from Lofoi lignite deposits (northwest Greece) is the subject of the present study. The samples were examined by means of X-ray diffraction (XRD), thermo-gravimetric (TG/DTG) and differential thermal analysis (DTA), and Fourier transform infrared (FT-IR) spectrometry. The clay minerals prevail in most samples, with illite-muscovite being the dominant phase, and kaolinite and chlorite being the other major clay components. No smectite was found. Quartz and feldspars, dominate in two cases. The studied materials are characterized as clays to clayey sands, showing significant similarities with the intraseam layers of the adjacent Achlada lignite deposits.     

Innovative methodologies in renewable energy: A review

This paper is concerned with innovative approaches to renewable energy sources computation methodologies, which provide more refined results than the classical alternatives. Such refinements provide additional improvements especially for replacement of fossil energy usages that emit greenhouse gas (GHG) into the atmosphere leading to climate change impact. Current knowledge gap among each renewable energy source calculation is rather missing fundamentals of plausible, rational, and logical explanations for the interpretation of results. In the literature, there are rather complicated and mechanically applicable methodologies, which require input and output measurement data match with missing physical explanations. The view taken in this review paper is to concentrate on quite plausible, logical, rational, and effectively applicable innovative energy calculation methodologies with simplistic fundamentals. For this purpose, a set of renewable energy methodological approaches is revisited with their innovative structures concerning solar, wind, hydro, current, and geothermal energy resources. With the increase in the renewable energy utilizations to combat the undesirable impacts of global warming and climate change, there is a need for better models that will include physical environmental conditions and data properties in the probabilistic, statistical, stochastic, logical, and rational senses leading to refined and more reliable estimations with application examples in the text. Finally, new research directions are also recommended for more refined innovative energy system calculations.     

Constrained Optimization of Heat Transfer from an Extended Surface

Two different zero‐order optimization techniques are used to maximize the rates of heat transfer from a fin assembly of a specified cost and in the shape of several annular fins that are mounted on a central stem. The problem is formulated to account for two‐dimensional steady‐state heat transfer that is limited by several inequality constraints. The dimensionless governing equations are used to identify the relevant decision variables. The number of fins making up the assembly is treated as an input parameter. A digital computer is used to determine the required temperature distributions and to implement the optimization search algorithms. Three different fin materials are assessed—aluminum, copper and carbon steel. Design optimizations of the extended surface assembly were made over a range of operating conditions, encompassing several different convection heat transfer coefficients that are representative of free and forced convection in air, and several different overall temperature differences between the substrate surface and air. A few recommendations based on trends in the predicted results are given. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res, 43(6): 504–521, 2014; Published online 3 October 2013 in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21093     

CY6D78Ti型柴油机的开发研制

本文介绍了CY6D78Ti型柴油机的开发研制过程及现状,CY6D78Ti型柴油机能满足国内中、重型卡车和豪华客车市场对柴油机动力性、经济性、可靠性的需求。由于该机型的高档配置,保证了其排放达到欧Ⅱ标准,同时为进一步提高性能、降低排放,采用电控及高压共轨等技术手段搭建了平台。     

我国车用柴油机的技术现状及发展趋势

本文根据国内外信息和资料，分析了我国目前车用柴油机制造技术方面与国际水平所存在的差距，预测今后若千年内车用柴油机要向节能降耗、应用增压技术、提高可靠性、降低排放、采用电控技术方面发展，以尽快接近和赶上国际先进水平．