热漏对内可逆四热源制冷系统的影响

在恒温热源内可逆四热源吸收式制冷循环的基础上，建立不可逆吸收式制冷循环的模型，考虑环境热源到制冷空间的热漏以及工质与外部热源间的热阻损失，导出牛顿定律下循环的制冷率和制冷系数的基本优化关系、最大制冷系数及相应的制冷率和最大制冷率及相应的制冷系数；并通过数值计算分析了循环参数对循环的制冷率、制冷系数的影响。     

内可逆四热源吸收式制冷循环的热经济性能优化

应用内可逆四热源吸收式制冷循环模型，分析吸收式制冷机受传热不可逆性影响时的热经济性能。在牛顿传热定律下，导出了循环的最佳热经济性目标和制冷系数的基本优化关系和最大热经济性目标及相应的制冷系数与比制冷率；通过数值算例，得出循环参数对循环的热经济性目标、制冷系数和比制冷率的影响关系。     

不可逆吸收式热泵循环的基本优化关系及性能分析

在恒温热源内可逆四热源吸收式热泵循环的基础上，建立了线性(牛顿)传热定律下考虑泵热空间到环境热源的热漏、工质的内部耗散以及工质与外部热源间的热阻损失的不可逆吸收式热泵循环模型。导出了总换热面积一定的条件下循环的泵热率和泵热系数的基本优化关系、最大泵热率和相应的泵热系数、最大泵热系数和相应的泵热率、以及循环中最佳工质工作温度和最佳换热面积分配关系；并通过数值算例分析了循环参数对循环最优性能的影响规律。     

q∝△(T-1)的不可逆吸收式制冷系统的优化

以内可逆吸收式制冷循环模型为基础，建立一个不可逆吸收式制冷循环的模型，该模型的热传导规律为q∝△（T^-1），包括低温热源到制冷空间的热漏及工质内部耗散，工质与外部热源间的有限热传导率的不可逆性，并用于导出制冷系数与制冷率的关系及在优质状态下的传热面积的分配关系。确定了在q∝△（T^-1）规律不可逆吸式制冷系统的主要参数的实际优选范围。     

热阻、热漏和内不可逆性对两级吸收式制冷循环性能的影响

建立考虑工质与外部热源间的传热损失、内不可逆性损失及外部热源热漏损失的不可逆两级吸收式制冷循环模型,给出制冷系数和制冷率的一般关系。在6个换热器总热导率一定时,对循环性能进行优化,导出循环制冷率和制冷系数的基本优化关系,并得到制冷率和制冷系数的极值。通过数值算例,分析热阻、热漏和内不可逆性损失对循环性能的影响规律。     

低焓能吸收式制冷系统的分析与改进

本文对简单吸收式制冷循环及三压吸收式制冷循环进行新的分析，并对三压吸收式制冷循环做了改进，从而较大幅度地提高了循环的热力系数，又不过分增加系统的复杂性，本文学分析了可以用于该循环的工质对问题。     

不可逆半导体固态热离子制冷器性能分析和优化

建立了考虑外部有限速率传热过程和热源间热漏的不可逆半导体固态热离子制冷器模型,基于非平衡热力学和有限时间热力学理论导出了热离子制冷器的制冷率和制冷系数的表达式;对比分析了不可逆热离子制冷器与可逆热离子制冷器的发射电流密度特性、电极温度特性以及制冷系数特性;研究了不可逆系统的制冷率与制冷系数最优性能,得到了制冷率和制冷系数的最优运行区间;通过数值计算,详细讨论了外部传热以及内部导热、热源间热漏损失、热源温度、外加电压、半导体材料势垒等设计参数对热离子装置性能的影响。在总传热面积一定的条件下,进一步优化了高、低温侧换热器的面积分配以获得最佳的制冷率和制冷系数特性。结果表明,由于存在内部和外部的不可逆性,热离子装置的发射电流密度及制冷系数都会明显降低;不可逆半导体固态热离子制冷器的制冷率与制冷系数特性呈扭叶型;合理地选外加电压、势垒等参数,可以使制冷器设计于最大制冷率或最大制冷系数的状态。     

内可逆四热源吸收式制冷机生态学最优性能

基于能量分析的观点,建立了反映四热源吸收式制冷机制冷率与熵产率之间最佳折中的生态学准则,分析了线性(牛顿)传热定律下内可逆四热源吸收式制冷机的生态学最优性能.导出了生态学目标与制冷系数的优化关系和最大生态学目标值及其相对应的制冷系数、制冷率和熵产率,确定了循环主要参数的生态学优化选择范围.数值算例分析了制冷率目标和生态学目标的相互关系,计算表明生态学准则对吸收式制冷机优化设计是一种具有长期效应的可选优化目标.     

传热规律、热漏和内不可逆性对吸收式热泵循环性能的影响

建立了考虑泵热空间到环境热源的热漏、工质循环的内部不可逆性以及工质与热源之间传热Q∝△(T^a)服从传热规律时的不可逆四热源吸收式热泵循环模型，导出了循环泵热率和泵热系数的一般关系；并导出了线性唯象传热定律时循环泵热率和泵热系数的基本优化关系、性能极值、循环中工质的最佳工作温度和换热器传热面积的最佳分配关系；通过数值耸例分析了传热规律、热漏和内不可逆性对循环性能的影响规律，比较了传热面积最优分配前后循环的最优性能。     

氨水吸收式制冷夹点分析法

氨水吸收式制冷需要消耗很大的公用工程,其性能系数(COP)不是很高,引入夹点分析法分析氨水吸收式制冷系统,该方法能够确定可回收的系统最大内部循环热,优化后的系统性能系数为0.623,比优化前的系统性能系数高11.58%。该方法对氨水吸收式制冷设计具有一定的指导意义。     

Performance assessment of some ice TES systems

In this paper, a performance assessment of four main types of ice storage techniques for space cooling purposes, namely ice slurry systems, ice-on-coil systems (both internal and external melt), and encapsulated ice systems is conducted. A detailed analysis, coupled with a case study based on the literature data, follows. The ice making techniques are compared on the basis of energy and exergy performance criteria including charging, discharging and storage efficiencies, which make up the ice storage and retrieval process. Losses due to heat leakage and irreversibilities from entropy generation are included. A vapor-compression refrigeration cycle with R134a as the working fluid provides the cooling load, while the analysis is performed in both a full storage and partial storage process, with comparisons between these two. In the case of full storage, the energy efficiencies associated with the charging and discharging processes are well over 98% in all cases, while the exergy efficiencies ranged from 46% to 76% for the charging cycle and 18% to 24% for the discharging cycle. For the partial storage systems, all energy and exergy efficiencies were slightly less than that for full storage, due to the increasing effect wall heat leakage has on the decreased storage volume and load. The results show that energy analyses alone do not provide much useful insight into system behavior, since the vast majority of losses in all processes are a result of entropy generation which results from system irreversibilities.     

Effect of co-cultivation of Chlamydomonas reinhardtii with Azotobacter chroococcum on hydrogen production

Chlamydomonas reinhardtii cc124 and Azotobacter chroococcum bacteria were co-cultured with a series of volume ratios and under a variety of light densities to determine the optimal culture conditions and to investigate the mechanism by which co-cultivation improves H₂ yield. The results demonstrated that the optimal culture conditions for the highest H₂ production of the combined system were a 1:40 vol ratio of bacterial cultures to algal cultures under 200 μE m^?2 s^?1. Under these conditions, the maximal H₂ yield was 255 μmol mg^?1 Chl, which was approximately 15.9-fold of the control. The reasons for the improvement in H₂ yield included decreased O₂ content, enhanced algal growth, and increased H₂ase activity and starch content of the combined system.     

Exergetic evaluation of 5 biowastes-to-biofuels routes via gasification

This paper presents the exergy analysis results for the production of several biofuels, i.e., SNG (synthetic natural gas), methanol, Fischer–Tropsch fuels, hydrogen, as well as heat and electricity, from several biowastes generated in the Dutch province of Friesland, selected as one of the typical European regions. Biowastes have been classified in 5 virtual streams according to their ultimate and proximate analysis. All production chains have been modeled in Aspen Plus in order to analyze their technical performance. The common steps for all the production chains are: pre-treatment, gasification, gas cleaning, water–gas-shift reactions, catalytic reactors, final gas separation and upgrading. Optionally a gas turbine and steam turbines are used to produce heat and electricity from unconverted gas and heat removal, respectively. The results show that, in terms of mass conversion, methanol production seems to be the most efficient process for all the biowastes. SNG synthesis is preferred when exergetic efficiency is the objective parameter, but hydrogen process is more efficient when the performance is analyzed by means of the 1st Law of Thermodynamics. The main exergy losses account for the gasification section, except in the electricity and heat production chain, where the combined cycle is less efficient.     

液压系统常见的故障诊断及处理

任何工程机械式液压设备使用时出现故障是不可避免的。但是怎样确定故障的原因及找到好的解决方法，这是使用者最关心的问题。讲述了液压系统常见的故障及其排除方法。     

Economie d'énergie en trigénération

Trigeneration is defined as the production of three useful forms of energy—heat, cold and power—from a primary source of energy such as natural gas or oil. For instance, trigeneration systems typically produce electrical power via a reciprocating engine or gas turbine and recover a large percentage of the heat energy retained in the lubricating oil, exhaust gas and coolant water systems to maximize the utilization of the primary fuel. The heat produced can be totally or partially used to fuel absorption refrigerators. Therefore, trigeneration systems enjoy an inherently high efficiency and have the potential to significantly reduce the energy-related operation costs of facilities. In this paper, we describe a model of characterization of trigeneration systems trough the condition of primary energy saving and the quality index, compared to the separate production of heat, cold and power. The study highlights the importance of the choice of the separate production reference system on the level of primary energy saving and emissions reduction.     

Mineralogical characterization of the intraseam layers of Lofoi lignite deposits in Florina basin (western Makedonia,northwest Greece)

The mineralogical composition of intraseam layers from Lofoi lignite deposits (northwest Greece) is the subject of the present study. The samples were examined by means of X-ray diffraction (XRD), thermo-gravimetric (TG/DTG) and differential thermal analysis (DTA), and Fourier transform infrared (FT-IR) spectrometry. The clay minerals prevail in most samples, with illite-muscovite being the dominant phase, and kaolinite and chlorite being the other major clay components. No smectite was found. Quartz and feldspars, dominate in two cases. The studied materials are characterized as clays to clayey sands, showing significant similarities with the intraseam layers of the adjacent Achlada lignite deposits.     

Innovative methodologies in renewable energy: A review

This paper is concerned with innovative approaches to renewable energy sources computation methodologies, which provide more refined results than the classical alternatives. Such refinements provide additional improvements especially for replacement of fossil energy usages that emit greenhouse gas (GHG) into the atmosphere leading to climate change impact. Current knowledge gap among each renewable energy source calculation is rather missing fundamentals of plausible, rational, and logical explanations for the interpretation of results. In the literature, there are rather complicated and mechanically applicable methodologies, which require input and output measurement data match with missing physical explanations. The view taken in this review paper is to concentrate on quite plausible, logical, rational, and effectively applicable innovative energy calculation methodologies with simplistic fundamentals. For this purpose, a set of renewable energy methodological approaches is revisited with their innovative structures concerning solar, wind, hydro, current, and geothermal energy resources. With the increase in the renewable energy utilizations to combat the undesirable impacts of global warming and climate change, there is a need for better models that will include physical environmental conditions and data properties in the probabilistic, statistical, stochastic, logical, and rational senses leading to refined and more reliable estimations with application examples in the text. Finally, new research directions are also recommended for more refined innovative energy system calculations.     

Constrained Optimization of Heat Transfer from an Extended Surface

Two different zero‐order optimization techniques are used to maximize the rates of heat transfer from a fin assembly of a specified cost and in the shape of several annular fins that are mounted on a central stem. The problem is formulated to account for two‐dimensional steady‐state heat transfer that is limited by several inequality constraints. The dimensionless governing equations are used to identify the relevant decision variables. The number of fins making up the assembly is treated as an input parameter. A digital computer is used to determine the required temperature distributions and to implement the optimization search algorithms. Three different fin materials are assessed—aluminum, copper and carbon steel. Design optimizations of the extended surface assembly were made over a range of operating conditions, encompassing several different convection heat transfer coefficients that are representative of free and forced convection in air, and several different overall temperature differences between the substrate surface and air. A few recommendations based on trends in the predicted results are given. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res, 43(6): 504–521, 2014; Published online 3 October 2013 in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.21093     

CY6D78Ti型柴油机的开发研制

本文介绍了CY6D78Ti型柴油机的开发研制过程及现状,CY6D78Ti型柴油机能满足国内中、重型卡车和豪华客车市场对柴油机动力性、经济性、可靠性的需求。由于该机型的高档配置,保证了其排放达到欧Ⅱ标准,同时为进一步提高性能、降低排放,采用电控及高压共轨等技术手段搭建了平台。     

我国车用柴油机的技术现状及发展趋势

本文根据国内外信息和资料，分析了我国目前车用柴油机制造技术方面与国际水平所存在的差距，预测今后若千年内车用柴油机要向节能降耗、应用增压技术、提高可靠性、降低排放、采用电控技术方面发展，以尽快接近和赶上国际先进水平．