Nd、Y对AZ31镁合金热轧退火薄板耐蚀性的影响

为提高AZ31镁合金热轧退火薄板的耐蚀性,本实验在合金中分别添加单一Nd和复合Nd+Y稀土元素,采用盐雾腐蚀和电化学腐蚀实验方法对其耐蚀性展开研究,并利用扫描电镜(SEM)、X射线衍射(XRD)仪对合金和腐蚀产物的微观组织及结构进行观察分析。结果表明:添加稀土元素Nd、Y后,AZ31镁合金表面可形成更为耐蚀的含有稀土氧化物Nd_2O_3的腐蚀产物膜,提高对基体的保护作用;添加Nd、Y元素的AZ31镁合金中新的耐蚀相Al_2Nd和Al_2Y析出,有害相β-Mg_(17)Al_(12)减少,使合金自腐蚀电位正移,腐蚀电流密度减小,腐蚀速率减缓,耐蚀性明显提高;复合添加Nd+Y比单一添加Nd更有利于提高AZ31镁合金的耐蚀性,且添加量为0.5%Nd+0.5%Y时合金的耐蚀性能提高最为显著。     

稀土Gd对AZ31镁合金耐蚀性能的影响

利用失重法研究不同Gd含量的AZ31镁合金在3.5%(质量分数,下同)Na2SO4溶液中的腐蚀行为,并采用OM,SEM和XRD等检测手段分析稀土Gd对AZ31镁合金微观组织、腐蚀速率和腐蚀形貌等的影响。结果表明:稀土Gd的添加能明显改善AZ31镁合金的耐蚀性能,且当Gd的添加量小于4.12%时,合金的耐蚀性能会随着Gd含量的增加而提高,但继续增大Gd含量时合金的耐蚀性能反而会出现一定程度的下降,其原因是合金中添加过多的Gd后,加剧了基体相与析出相之间的微电偶腐蚀,致使合金的耐蚀性能有所下降。故当Gd的添加量为4.12%时,AZ31镁合金的耐蚀性能最佳。     

稀土对AZ91镁合金干/湿循环腐蚀产物及阻抗行为的影响

采用扫描电镜(SEM)、X射线衍射(XRD)、能谱分析(EDS)研究添加(La,Ce)混合稀土前后AZ91镁合金在融雪剂溶液中经历干/湿交替循环腐蚀后腐蚀产物的组成和结构。结果表明:未添加(La,Ce)混合稀土的AZ91镁合金的腐蚀产物主要由Mg(OH)_2,MgO,CaCO_3及Mg_6Al_2CO_3(OH)_(16)·4H_2O组成;而添加混合稀土的AZ91镁合金表面生成了(La,Ce)AlO_3等含稀土元素的腐蚀产物,同时腐蚀产物出现致密层。不同周期干/湿交替循环腐蚀的电化学阻抗谱(EIS)测试结果表明,添加(La,Ce)混合稀土的镁合金在相同腐蚀周期的阻抗谱幅值均高于AZ91镁合金的阻抗谱幅值,稀土的添加有助于降低阻抗谱的弥散效应,表明(La,Ce)混合稀土可以提高AZ91镁合金在干/湿交替腐蚀环境中的耐蚀性和腐蚀产物膜的稳定性。     

AZ91铸态镁合金中Mn含量对其微观组织及耐蚀性能的影响

目前,关于Mn对AZ91铸态镁合金耐蚀性能影响的研究并不充分,尤其是腐蚀机制方面仍不清楚。采用静态失重、电化学及盐雾腐蚀法研究了Mn含量对AZ91铸态镁合金微观组织及耐腐蚀性能的影响。利用金相显微镜(OM)、扫描电镜(SEM)观察AZ91铸态镁合金的微观组织和腐蚀形貌,采用能谱(EDS)仪、X射线衍射仪(XRD)分析了其物相组成。结果表明:AZ91铸态镁合金中的Mn主要以颗粒状的低电化学活性物质Al2Mn形式存在,阻碍了其腐蚀过程的进行;Mn能使AZ91铸态镁合金中的有效腐蚀相β-Mg17Al12减少,分布更弥散,从而使合金的腐蚀电位升高,腐蚀电流降低,腐蚀速率降低,耐腐蚀性能增强;含0.8%Mn的铸态镁合金的耐腐蚀性能最好。     

AZ31和稀土镁合金微弧氧化膜的对比研究

在相同的工艺参数下制备了AZ31和Mg 10Gd 2Y-0.4Zr稀土镁合金微弧氧化膜层.利用SEM、XRD和EDS对两种陶瓷膜层的组成、微观形貌和元素组成进行了表征;通过电化学测试和盐雾试验评价了两种陶瓷膜层的耐蚀性能;利用显微硬度仪研究了两种陶瓷膜的显微硬度.结果表明:两种陶瓷层的厚度、表面形貌和致密性相似;陶瓷膜由MgO和Mg2SiO4组成,其中MgO为主晶相;与AZ31镁合金陶瓷膜相比,稀土镁合金陶瓷膜中的MgO含量增多,Mg2SiO4含量减少;两种镁合金表面陶瓷化后的耐蚀性和硬度大大提高,AZ31镁合金陶瓷膜耐蚀性优于稀土镁合金陶瓷膜,稀土镁合金陶瓷膜的硬度高于AZ31镁合金陶瓷膜.     

微量稀土Nd对AZ91微观组织及腐蚀性能的影响

采用X-射线衍射(XRD)、扫描电镜(sEM)、能谱分析(EDS)、集气法、动电位极化及浸泡实验等手段和方法研究了添加微量稀土元素钕(Nd)对AZ91镁合金微观组织及耐蚀性的影响,并从热力学角度分析了Nd对提高合金耐蚀性的影响机制.结果表明.少量稀土Nd细化了合金的微观组织,使β-Mg17Al12相变得断续、弥散,生成了Al3Nd相及Mg-Al-Mn-Nd-Fe金属问化合物;稀土Nd使合金在3.5%NaCl溶液中的自腐蚀电位升高,且与Al、O生成了不连续的致密的氧化膜,提高了合金的耐腐蚀性能;添加1.0wt%Nd时合金的耐蚀性最佳,腐蚀速率为0.28 mg·cm-2·d-1,比AZ91合金下降了一个数量级.     

Nd对AZ91镁合金显微组织和耐腐蚀性能的影响

用金相显微镜、扫描电镜和静态质量损失法对AZ91-xNd镁合金(x=1.1%,1.4%,1.9%)的微观组织和腐蚀性能进行表征,研究了Nd对AZ9l镁合金显微组织和耐腐蚀性能的影响.结果表明:稀土Nd的添加明显细化了合金的组织,使半连续网状β(Mgl7Al12)相变为细小的长条状,且分布更加均匀.在合金中还生成了颗粒状...     

合金元素Nd对AZ系镁合金牺牲阳极材料耐腐蚀和电化学性能的影响

目前,关于稀土元素Nd对镁合金阳极耐腐蚀性和电化学性能影响的报道较少。向AZ31和AZ63镁合金中加入稀土元素Nd,测试了AZ31和AZ63镁合金加入Nd元素前后在3.5%NaCl溶液中的静态析氢腐蚀速率、失重腐蚀速率、极化曲线和电流效率,观察了镁合金试样的显微组织与腐蚀形貌;研究了合金元素Nd对AZ31、AZ63镁合金牺牲阳极的耐腐蚀与电化学性能的影响。结果表明:合金元素Nd的加入能使AZ31、AZ63镁合金晶粒细化、组织均匀,自腐蚀速率降低、电流效率提高;加入Nd元素后,AZ31,AZ63镁合金的阳极极化没有明显增加。     

添加稀土Gd对Mg-6Al镁合金组织和耐蚀性的影响

Mg-6Al镁合金具有较好的铸造性能和力学性能,目前鲜见单一稀土元素对其腐蚀性能影响的报道。通过合金制备、微观组织分析和耐蚀性测试等方法研究了稀土Gd添加量对Mg-6Al镁合金微观组织和耐蚀性能的影响。OM、SEM、EDS、XRD分析结果表明,稀土Gd的添加改善并细化了Mg-6Al合金的铸态组织,形成杆状或块状的Al2Gd新相;动电位极化、浸泡试验等测试结果表明Gd的添加显著提高了Mg-6Al合金在3.5%NaCl溶液中的耐腐蚀性能,Mg-6Al-2%Gd镁合金的腐蚀速度最小,为0.83 mm/a,且腐蚀后组织较为致密,腐蚀产物和腐蚀坑均变小,Mg-6Al-x Gd合金的腐蚀产物主要为Mg(OH)2。     

工艺参数对镁合金植酸转化膜的影响

传统铬酸盐化学转化处理能提高镁合金的耐腐蚀性能,但因处理液有剧毒而受到限制.采用环保型金属处理剂植酸对AZ31B镁合金进行化学转化处理,通过正交试验初步确定了工艺参数(植酸浓度、处理液pH值、处理时间、处理温度)对植酸转化膜耐蚀性影响的主次顺序,并优化了工艺参数.采用扫描电子显微镜(SEM)、电子能谱仪(EDS)、光学金相显微镜对植酸转化膜腐蚀前后的形貌、成分和厚度进行了分析;通过电化学测试技术和化学浸泡法测试了其耐蚀性能.结果表明:与传统的铬酸盐和磷酸盐体系相比,经植酸处理后,AZ31B镁合金在3.5%NaCl溶液中的腐蚀电位分别提高了0.06 V和0.09 V,且在相同的电位下,阳极电流密度最小,电化学性能得到显著改善,腐蚀速度降低.     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.     

空压机轴承箱蜗壳温度探头油封改造

由于空压机进气侧轴承箱蜗壳温度探头密封效果不好,使空压机及其后续管道受到油污染。后将温度探头的O形圈密封改为骨架油封,杜绝了轴承箱漏油问题。文章简介空压机的结构和技术参数,详细介绍了骨架油封的制作和优点。     

Characteristics of mechanical properties of materials in studies of conditions of attainment of marginal states

It is shown that conditions of attainment of marginal states in the material of structural components are formulated on the basis of analysis of force and deformation criteria of formation and development of destruction. The parameters of these criteria are data on types of structural materials, standard and special characteristics of their mechanical properties, structural forms of considered elements of the equipment, and their operating stress loading. In this case, the construction of a system of state equations for describing interrelation of current damage, external actions, and responses to them is based on the concept of calculating variations in properties of materials at all stages of the design life cycle.     

Determination of parameters of microstructural inhomogeneity of deformation of metals by the method of modeling

The article suggests a method of evaluating the microstructural inhomogeneity of deformation of metals by modeling. The method includes the measurement of deformations of metal according to meshes of a dividing grid with small base and the calculation of the distribution parameters of microdeformations in model representation. It is shown that the modeling method makes it possible objectively to evaluate the microinhomogeneity of deformation of metals independently of the chosen mesh size of the dividing grid. New structural characteristics are introduced: the base and wave of variation expressing the degree of crumbling or amalgamation of metal grains by inhomogeneity of deformation.Translated from Problemy Prochnosti, No. 7, pp. 40–44, July, 1991.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

水三相点复现的不确定度评定

水三相点是开尔文热力学温度的唯一基准点，也是ITS-90国际温标重要的定义固定点。因此，水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来，中国计量科学研究院研制出一系列高质量的水三相点容器，加强了水三相点的研究，为不确定度的分析提供了更为可靠的实验依据。同时，不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此，根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明，其扩展不确定度为0．16mK(k=2．69，P=0．99)。