汽车覆盖件用 5 B003 A 板拉伸实验及成形性的有限元分析

目的研究汽车车身用5B003A板的成形性能。方法在进行单轴拉伸试验的基础上,利用软件eta/DYNAFORM模拟了板成形极限曲线、破裂点应变路径、圆筒拉深过程,并进行了相应变形参数的优化。结果 5B003A板单向拉伸和有限元模拟均出现"交叉颈缩"现象,并且在与轧制呈45°角方向上的冲压性能优于0°和90°方向;5B003A板成形极限破裂点的应变路径漂移倾向较明显,双拉区中均呈ε2=const的应变状态;在与拱顶高实验相近变形条件下,优化得到最佳凸模圆角半径为20 mm时,与极限拉深系数0.43对应的无凸缘拉深的最大板坯尺寸为233 mm,相应最佳压料力为68 kN。结论 5B003A板在45°方向上有较好的冲压性能,且凸模圆角半径、板坯直径、压料力等工艺参数对其拉深成形性能影响较大。     

材料参数对汽车发动机隔热板冲压成型性能影响

本文利用拉伸试验获得的样本数据,通过冲压性能试验和膨胀性实验,分析汽车用铝合金板材料参数和其成形性之间的对应关系,建立了评估铝合金板胀性成形性和拉深性的指标,为发动机隔热板冲压成形合理选材和预测成形性提供可靠的依据,为其它铝制品零件冲压加工中合理选材和预测成形性提供参考性的依据。     

镁合金板拉深及拉胀复合成形性能实验研究

通过实验,研究了镁合金板的拉深以及拉深+胀形复合性能,对这一新材料的冲压变形规律有了一定认识,得到了一些有实用价值的数据:极限拉深系数、壁厚变化、锥杯值以及一些塑性变形现象.     

铝合金 2A16 板材成形极限研究

目的掌握硬铝合金在温热条件下的成形性能变化规律。方法采用结合半球凸模胀形和椭圆液压胀形的复合试验法进行了FLD试验,用最小二乘法拟合试验数据,建立了成形极限预测模型。结果试样均在凸模顶端或附近发生破裂,在室温下网格保持较小的圆形,在210℃和300℃下网格被不同程度的拉长和变大,温度对铝合金2A16的成形性能影响很大,随温度升高,成形极限曲线上移。结论复合胀形试验法具有较高的可靠性与准确性;铝合金2A16在高温下成形性能更好;预测模型较好地表述了极限应变值与温度的关系,根据模型可快速得出FLD。     

超级钢板料冲压性能的拉伸试验研究

将超级钢应用于国产汽车冲压件的生产中不仅可以提高汽车质量,而且可以降低汽车的成本、减小汽车重量、降低能源消耗和减少环境污染.为了在汽车工业中更好地使用超级钢,概述了板材冲压性能的评价指标,介绍了拉伸试验值对板材冲压性能的影响,并对超级钢进行了拉伸试验.研究了超级钢板的硬化指数、塑性应变比、屈服强度、极限强度、均匀延伸率等机械性能,并分析了超级钢板的冲压成形性能,超级刚具有较好的胀形性能、拉深性能、弯曲性能,抗起皱性能等冲压性能,可以广泛地应用于汽车冲压零件生产中.     

基于Oyane韧性断裂准则的板料成形极限预测

本文基于Oyane韧性断裂准则,结合数值模拟方法,预测板料不同应变状态下的极限应变.准则中的材料参数通过单向拉伸和平面应变拉伸试验确定.在模拟胀形试验获得每一时间步应力、应变值的基础上,应用韧性断裂准则预测板料的成形极限.模拟结果表明用韧性断裂准则和数值模拟相结合的方法能成功获得板料的成形极限图.     

纤维金属层合板冲压成形性能研究现状

本文综述了纤维金属层合板(FMLs)在基本力学性能、单向拉伸、弯曲、拉深成形及半球胀形等方面的研究,旨在全面了解FMLs表面处理方式、组分材料厚度、成形工艺条件、模具结构参数、中间纤维铺层方向及铺层方式等因素对材料冲压成形性能的影响,为研发和制造新型轻量化FMLs车身构件进行合理的材料铺层设计、确定优化工艺方案提供依据.指出了建立相应FMLs材料性能预测模型、本构关系模型、成形极限理论、破裂失效判据的必要性和紧迫性.     

换热器用纯钛TA1薄板冷成形性

一、前言 钛的密度低、强度高,具有优异的耐蚀性能,用钛制作板式换热器有很强的竞争力。我国目前有不少厂家用冷压法制造钛板式换热器。换热器的板面有凸起、波纹,形状复杂,在冷态压制过程中容易产生裂纹。钛的价格昂贵,提高冲压件的成品率,降低成本有较大的经济效益。评估板料的成形性试验方法,广泛采用的是单向拉伸试验和模拟试验两种方法。单向拉伸测得的应变硬化指数“n”与厚向异性指数“γ”值是板料成形性的重要指标。n值反映板料成形时抵抗拉伸失稳、变形均匀化的能力。零件在以拉为主的变形方式中,n大的材料应变分布均匀,表面质量好,不易产生裂纹,成形性好。相反,n小的材料变形分布不均匀,表面粗糙,容易产生裂纹。γ值表示板料抵抗变薄的能力,γ愈大,变形时愈不易变薄,对拉深变形有利。但在弯曲时γ大,则外层材料不易变薄,反而容易开裂,因而γ大弯曲性能差。模拟试验按HB640—87。对于国产TA1薄板的冲压性能至今还没有进行系统的研究。本文测试了换热器用TA1板的拉伸性能σ_b,σ_(0.2),δ,n和γ值,还进行了杯突、拉深、     

铝合金复杂曲面薄壁件液压成形技术

介绍了适合于制造铝合金复杂曲面薄壁件的液压成形技术,包括充液拉深、可控径向加压充液拉深和液体凸模拉深。由于充液拉深能提高成形极限,适合于制造铝合金复杂型面零件。可控径向加压充液拉深通过径向压力向内推料,进一步提高了成形极限,适合于成形大高径比筒形件。液体凸模拉深适合于获得深度较大、形状复杂、尤其底部具有小过渡圆角的复杂形状零件。     

AZ31镁合金板锥杯与扩孔成形性能研究

对AZ31镁合金板在20~300℃条件下进行了拉伸力学性能、锥杯及扩孔试验研究。结果表明:随着变形温度的升高,AZ31镁合金板抗拉强度逐渐下降而延伸率不断提高;随着温度升高,锥杯值CCV逐渐减小,300℃时具有较小的锥杯值CCV,获得了较好的“拉深+胀形”复合成形性能;随着温度升高,AZ31镁合金板的扩孔成形性能显著提高。     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.