基于多目标进化算法的PMU的优化配置

研究了配置相量测量单元(PMU)后电力系统可观测性的判断方法,以保证电力系统完全可观测为约束条件,以配置PMU数目最小和保证测量量具有最大量测冗余度为目标,建立了PMU最优配置问题的数学模型。这是一个多目标优化问题,需要寻求一组Pareto最优解,应用多目标进化算法求解该问题可以得到多种满足条件的PMU配置可行方案。最后,以IEEE39节点系统为例验证了该方法的合理性。     

Optimal PMU placement method for complete topological and numerical observability of power system

This paper presents a new method of optimal PMU placement (OPP) for complete power system observability. A two-stage PMU placement method is proposed, where stage-1 finds out the minimum number of PMUs required to make the power system topologically observable and stage-2 is proposed to check if the resulted PMU placement (from stage-1) leads to a full ranked measurement Jacobian. In case the PMUs placed, ensuring topological observability in stage-1, do not lead to the Jacobian of full rank, a sequential elimination algorithm (SEA) is proposed in stage-2 to find the optimal locations of additional PMUs, required to be placed to make the system numerically observable as well. The proposed method is tested on three systems and the results are compared with three other topological observability based PMU placement methods. The simulation results ensure the complete system observability and also demonstrate the need of using stage-2 analysis along with the topological observability based PMU placement methods.     

Minimizing the number of PMUs and their optimal placement in power systems

This paper presents a new method for minimizing the number of PMUs and their optimal placement in power systems. The proposed method provides suitable constraints for power systems with two adjacent injection measurements (IMs). In addition, suitable constraints for considering the connection of two buses to each other and to an injection bus are proposed. The proposed constraints result in a reduction in the number of PMUs even though the system topological observability is complete. Existing conventional measurements are also considered. First, the number of PMUs is minimized in such a way that the system topological observability is complete. Then the optimal placement is done to maximize the measurements redundancy. The resulting phased to be installed in multiple stages. The optimal number of PMUs that ensure system topological observability under failure of a PMU or a line is also simulated. Simulations are performed on IEEE 30, 57 and 118 bus test systems by binary integer programming. The results show that the number of PMUs is equal to or less than the corresponding results of recently published papers, while the system topological observability is complete, and measurement redundancy is increased.     

基于改进的整数规划法结合零注入节点的PMU优化配置方法

为了提高同步相量测量装置的优化速度并利用最少数量的相量量测单元(PMU),结合零注入节点的特性,提出了基于整数规划算法的PMU优化配置算法。根据电力系统全网的可观测性建立其数学模型,并考虑了零注入节点的相关特点,求解系统模型获得PMU的优化位置。对IEEE-14节点、IEEE-18节点、IEEE-30节点以及IEEE-118节点系统分别进行了实验仿真,并利用Matlab以及Lingo工具对所提改进的整数规划法进行了验证,对约束方程进行优化,获得了PMU的数量和位置。将该算法与整数规划算法、模拟退火法以及改进过的遗传算法相比较,该算法可以用更少数量的PMU设备使全网可观,验证了该方法的有效性和优越性。     

Novel Clustering-based Hidden Markov Model (CHMM) optimization approach for optimal PMU placement

A Phasor Measurement Unit (PMU) is an important device for monitoring the wide-area power distribution network. Placement of the PMUs across the network enables reliable monitoring of the network to identify the faults in the bus system. Due to the increase in the installation cost of the PMUs, optimal placement of the PMU is a significant task. But the existing techniques do not provide the optimal solution for the PMU placement. To overcome this issue, this paper proposes a novel Clustering-based Hidden Markov Model (CHMM) optimization approach to achieve optimal placement of PMUs in the power distribution network. Optimal PMU placement is achieved by applying cluster formation in the bus system to extract the data with neighboring buses. Best optimal position for placing the PMU is estimated by using Fuzzy logic-based rale formation to update the binary table of the bus system. The HMM approach is used for updating weight in the cluster formation. Our system is implemented in various bus systems like IEEE 28-bus system, 69-bus system and also in Karnataka 155-bus system. The proposed approach is implemented in the IEEE bus system and Karnataka Power Transmission Corporation Limited (KPTCL) bus system and compared with the existing approaches, based on the total number of PMU placement. The proposed approach achieves better performance in the optimal placement of PMU than the existing optimization algorithms.     

Optimal allocation of phasor measurement unit for full observability of the connected power network

This paper presents binary particle swarm optimization (BPSO) technique for the optimal allocation of phasor measurement units (PMUs) for the entire observability of connected power network. Phasor measurement units are considered as one of the most important measuring devices in the prospect of connected power network. PMUs function may be incorporated to the wide-area connected power networks for monitoring and controlling purposes. The optimal PMU placement (OPP) problem provides reference to the assurance of the minimal number of PMUs and their analogous locations for observability of the entire connected power networks. Binary particle swarm optimization (BPSO) algorithm is developed for the solution of OPP problem. The efficacy and robustness of the proposed method has been tested on the IEEE 14-bus, IEEE 30-bus, New England 39-bus, IEEE 57-bus, IEEE 118-bus and Northern Regional Power Grid (NRPG) 246-bus test system. The results obtained by proposed approach are compared with other standard methods and it is observed that this BPSO based placement of phasor measurement units is found to be the best among all other techniques discussed.     

基于改进粒子群算法的PMU装置数量增加过程中的最优配置方法

针对现有电力系统相量测量装置(PMU)在系统中的最优配置问题,进一步考虑了系统发展过程中PMU数量增加的最优配置问题。以电力系统线性量测模型为基础,通过拓扑分析方法,以全系统可观为约束,以系统最大冗余度为目标,并使用改进的粒子群算法进行计算,实现PMU数量增加过程中的最优配置。通过算例证明了算法的有效可靠。     

考虑系统完全可观测性的PMU最优配置方法

基于电力系统线性量测模型，研究了引入相量测量单元（PMU）相关量测集后的增广关联矩阵的电力系统可观测性拓扑分析方法，以保证系统结构完全可观测性和最大量测数据冗余度为约束，以配置PMU数目最小为目标，形成了PMU最优配置问题，并应用禁忌搜索（TS）方法求解该问题，保证了全局寻优。算例表明，该方法准确可靠、有效可行。     

一种改进的相量测量装置最优配置方法

以电力系统状态完全可观测和相量测量装置(PMU)配置数目最小为目标,提出了一种改进的PMU最优配置方法.将启发式方法和模拟退火方法有效结合以确保得到最优解,提高了基于启发式方法的初始PMU配置方案的质量,通过改进配置模型缩小了模拟退火方法的寻优范围,从而提高了求解速度.还提出了一种基于节点邻接矩阵的快速可观测性分析方法.最后采用IEEE 14、IEEE 30、IEEE 118节点系统和新英格兰39节点系统对该方法进行了验证.     

Optimal placement of PMUs with limited number of channels for complete topological observability of power systems under various contingencies

In optimal PMU placement problem, a common assumption is that each PMU installed at a bus can measure the voltage phasor of the installed bus and the current phasors of all lines incident to the bus. However, available PMUs have limited number of channels and cannot measure the current phasors of all their incident lines. The aim of this paper is to recognize the effect of channel capacity of PMUs on their optimal placement for complete power system observability. Initially, the conventional full observability of power networks is formulated. Next, a modified algorithm based on integer linear programming model for the optimal placement of these types of PMUs is presented. The proposed formulation is also extended for assuring complete observability under different contingencies such as single PMU loss and single line outage. Moreover, the problem of combination of PMUs with different number of channels and varying costs in optimal PMU placement is investigated. Since the proposed optimization formulation is regarded to be a multiple-solution one, total measurement redundancy index is evaluated and the solution with the highest redundancy index is selected as the optimal solution. The proposed formulation is applied to several IEEE standard test systems and compared with the existing techniques.     

基于改进自适应遗传算法的系统可观测PMU最优配置

以电力系统配置同步相量测量单元（PMU）个数最少、系统有最大测量冗余度为目标,全网可观测为约束,提出PMU最优配置模型,同时针对实际电网中存在某些重要节点已经初步安装PMU或者必须安装PMU的情况,提出了特殊约束条件,并给出了相应的求解算法。在此基础上,用改进自适应遗传算法求解此模型,保证全局最优。对某省49节点电网进行的计算表明,改进的自适应遗传算法收敛到全局最优解的概率优于传统的遗传算法和自适应遗传算法,更适用于工程实际。     

电力系统相量测量装置最优配置混合算法的研究

以电力系统状态完全可观测和相量测量装置(PMU)配置数目最小为目标,形成了PMU最优配置问题。将遗传算法和禁忌算法有效结合形成禁忌遗传算法,该算法在改进交叉和变异算子的基础上,继承和发展了遗传算法基于多点搜索、鲁棒性强等诸多优点,每当群体有出现早熟而陷入局部最优解的趋势时,利用禁忌搜索增强算法的爬山能力,避免算法早熟而陷入局部最优解,增强算法的全局收敛能力和收敛速度。与遗传算法和禁忌搜索方法相比,禁忌遗传算法具有更好的全局收敛能力和收敛速度。最后采用IEEE14,IEEE30和IEEE57节点系统对算法的有效性进行了验证。     

A Multi-objective PMU Placement Method in Power System via Binary Gravitational Search Algorithm

This paper presents a Binary Gravitational Search Algorithm (BGSA) methodology for the optimal placement of Phasor Measurement Units (PMUs) to achieve full and maximum observability of the power system. The gravitational search technique has been extended in this investigation to incorporate binary variables for this purpose. The objective of proposed methodology is to minimize the total number of PMUs installed at various buses, which in turn minimize installation cost of the PMUs and improves observability redundancy by including an additional objective. Thus, the PMU placement problem has been expressed as a multi-objective problem. Besides, single PMU outage or single line outage cases in the presence of zero injection buses have been investigated. In this algorithm, the searcher agents are the collection of masses, which interact with each other using Newton's laws of gravity and motion. The proposed BGSA has been applied to the IEEE 14-bus, -30-bus, -118-bus, Northern Regional Power Grid 246-bus Indian system, and Polish 2383-bus system. Case studies reveal that the lower number of PMUs or equal number of PMUs has been produced by the proposed method compared to methods reported in the literature. In cases of equal number of PMUs, the observability produced by proposed method is higher or at least equal.     

基于01整数规划的多目标最优PMU配置算法

针对目前缺乏多目标PMU配置方法,提出了一种基于线性01规划的多目标优化配置算法。并在此基础上导出了三种特殊模型,分别处理系统在正常运行方式下完全可观测的PMU布点问题,在线路N-1故障时系统仍可观测的PMU布点问题及在PMU N-1故障时系统仍可观测的PMU布点问题。该方法的突出特点在于能够同时将以上三种布点需求使用统一的形式同时处理,并且最终的布点方案在保证PMU数目最少或保证配置PMU所需费用最少的基础上获得了最高的测量冗余度。通过IEEE30、IEEE 57、IEEE118节点系统布点验证了该方法的有效性和灵活性。     

电力系统PMU最优配置数字规划算法

随着相量量测装置(PMU)硬件技术的逐渐成熟和高速通信网络的发展,PMU在电力系统中的状态估计、动态监测和稳定控制等方面得到了广泛应用.为达到系统完全可观,在所有的节点上均装设PMU既不可能也没有必要.文中提出一种基于系统拓扑可观性理论的数字规划算法,利用PMU和系统提供的状态信息,最大限度地对网络拓扑约束方程式进行了简化,以配置PMU数目最小为目标,形成了PMU最优配置问题,并采用禁忌搜索算法求解该问题.其突出优点是利用了系统混合测量集数据,即不仅考虑了PMU实测数据,同时计及了可用的潮流数据.在IEEE14节点和IEEE 118节点系统的仿真结果表明,与常规的PMU最优配置算法相比,所提出的数字规划算法可以实现安装较少数量的PMU而整个系统可观的目标.     

基于免疫BPSO算法与拓扑可观性的PMU最优配置

以电力系统状态完全可观测和相量测量单元PMU配置数目最小为优化目标,基于PMU的功能特点和电力网络的拓扑结构信息,形成快速且通用的电网拓扑可观测性判别方法,并设计了一种结合免疫系统信息处理机制的二进制粒子群优化算法对目标函数进行求解,该算法综合了粒子群优化算法简单快速和免疫系统种群多样性的优点,明显改善了进化后期算法的收敛性能和全局寻优能力.最后通过对IEEE14和新英格兰39母线系统进行PMU优化配置仿真及量测冗余性分析,验证了本文方法的有效性和优越性.     

兼顾元件权重和发电机同调性的山东电网PMU布点方法

在稳定计算的基础上,对于相量测量单元(phasor measurement unit,PMU)最优配置问题,进行了可观性权重设置和机组同调性分析。首先把逐点法与穷举法结合到一起形成了一种新的静态可观性改进算法,并引入了元件权重的概念来区分对不同设备可观性要求的程度;然后考虑了发电机同调性的影响,以可观性布点为基础,形成了动态可观性的布点;最后根据山东电网2006年夏季大方式的稳定计算结果,结合可观性和发电机同调性,提出了一种分阶段实施的有效PMU布点方法。     

Placement of Synchronized Measurements for Power System Observability

This paper presents a method for the use of synchronized measurements for complete observability of a power system. The placement of phasor measurement units (PMUs), utilizing time-synchronized measurements of voltage and current phasors, is studied in this paper. An integer quadratic programming approach is used to minimize the total number of PMUs required, and to maximize the measurement redundancy at the power system buses. Existing conventional measurements can also be accommodated in the proposed PMU placement method. Complete observability of the system is ensured under normal operating conditions as well as under the outage of a single transmission line or a single PMU. Simulation results on the IEEE 14-bus, 30-bus, 57-bus, and 118-bus test systems as well as on a 298-bus test system are presented in this paper.      

基于记忆的改进克隆算法及其PMU配置多目标优化应用

以PMU安装数、量测系统可观测性和基于混合量测的状态估计精度三者为优化目标的PMU优化配置(OPP)是二层规划问题。该文证明了用单次状态估计精度评价量测系统性能的可行性，提出精度加权估算公式。将二层规划目标简化为分段函数，提出基于记忆的改进克隆算法。除模仿生物免疫系统的克隆选择和受体编辑机制外，该算法引入记忆加速算子以强化邻域搜索，并分段调整循环补充规模、高频变异与重组操作概率，从而显著加快和稳定进化进程，避免搜索陷入局部最优解。基于IEEE 14/57节点系统的算例表明，该算法能快速稳定地求出全局最优解及近似解，比原克隆算法等更适用。     

基于相量量测的等式约束二阶段状态估计模型

利用PMU的量测信息实现系统的动态可观测，考虑PMU数据刷新时间快的特点，在R.F.Nuqui的动态监测模型的基础上建立了适合静态估计的基于等式约束二阶段估计模型。该模型将PMU和SCADA的量测数据共同用于非线性估计，采用零注入节点功率作为等式约束条件来提高估计精度，然后对非线性估计的结果和PMU的支路电流相量进行线性估计。模拟了当系统某节点负荷持续变化时，利用等效导纳法对非线性区域节点状态量进行估计,最后采用IEEE 14和57节点系统算例对提出的模型进行了验证。