A comparative design study of continuous‐time incremental sigma‐delta ADC architectures

This paper presents a comparative design study of continuous‐time (CT) incremental sigma‐delta (IΣΔ) ADCs, which can expand another dimension of the IΣΔ ADC world that is dominated by discrete‐time implementations. Several CT IΣΔ ADC architectures are introduced and analyzed aiming to reduce the modulator's sampling frequency and consequently the power dissipation. Based on the analytical results, three CT IΣΔ ADCs are selected to be examined, implemented, and tested. The three ADC prototypes, fabricated in a standard 0.18‐m CMOS technology, demonstrate competitive figure‐of‐merits in terms of power efficiency compared to the state‐of‐the‐art counterparts. Copyright © 2016 John Wiley & Sons, Ltd.     

A 1.2 V 83 dB DR single‐ended input SC ΔΣ modulator including a large‐swing analog buffer for portable ECG applications

This study proposes a subsystem consisting of an analog buffer and a single‐ended input to a fully differential ΔΣ modulator to obtain low‐power consumption for portable electrocardiogram applications. With the proposed subsystem, the need for an inverting amplifier is avoided, and low‐power consumption is achieved. The ΔΣ modulator with a second order, 1 bit, and cascade of integrators feedforward structure consumes a low power, in which an inverting and a non‐inverting path implement a single‐ended input to fully‐differential signals. A double sampling technique is proposed for a digital‐to‐analog converter feedback circuit to reduce the effect of the reference voltage, reduce the amplifier requirements, and obtain low‐power consumption. Input‐bias and output‐bias transistors working in the weak‐inversion region are implemented to obtain an extremely large swing for the analog buffer. At a supply voltage of 1.2 V, signal bandwidth of 250 Hz, and sampling frequency of 128 kHz, the measurement results show that the modulator with a buffer achieves a 77 dB peak signal‐to‐noise‐distortion ratio, an effective‐number‐of‐bits of 12.5 bits, an 83 dB dynamic range, and a figure‐of‐merit of 156 dB. The total chip size is approximately 0.28 mm² with a standard 0.13 µm Complementary Metal‐Oxide‐Silicon (CMOS) process. Copyright © 2016 John Wiley & Sons, Ltd.     

A low‐power small‐area 10‐bit analog‐to‐digital converter for neural recording applications

In vivo neural recording systems require low power and small area, which are the most important parameters in such systems. This paper reports a new architecture for reducing the power dissipation and area, in analog‐to‐digital converters (ADCs). A time‐based approach is used for the subtraction and amplification in conjunction with a current‐mode algorithm and cyclical stage, which the conversion reuses a single stage for three times, to perform analog‐to‐digital conversion. Based on introduced structure, a 10‐bit 100‐kSample/s time‐based cyclical ADC has been designed and simulated in a standard 90‐nm Complementary Metal Oxide Semiconductor (CMOS) process. Design of the system‐level architecture and the circuits was driven by stringent power constraints for small implantable devices. Simulation results show that the ADC achieves a peak signal‐to‐noise and distortion ratio (SNDR) of 59.6 dB, an effective number of bits (ENOB) of 9.6, a total harmonic distortion (THD) of ?64dB, and a peak integral nonlinearity (INL) of 0.55, related to the least significant bit (LSB). The ADC active area occupies 280µm × 250µm. The total power dissipation is 5µW per conversion stage and 20µW from an 1.2‐V supply for full‐scale conversion. Copyright © 2010 John Wiley & Sons, Ltd.     

A 0.8‐V supply bulk‐driven operational transconductance amplifier and Gm‐C filter in 0.18 µm CMOS process

A low voltage bulk‐driven operational transconductance amplifier (OTA) and its application to implement a tunable Gm‐C filter are presented. The linearity of the proposed OTA is achieved by nonlinear terms cancelation technique, using two paralleled differential topologies with opposite signs in the third‐order harmonic distortion term of the differential output current. The proposed OTA uses 0.8 V supply voltage and consumes 31.2 μW. The proposed OTA shows a total harmonic distortion of better than ?40 dB over the tuning range of the transconductance, by applying 800 mV_ppd sine wave input signal with 1 MHz frequency. The OTA has been used to implement a third‐order low‐pass Gm‐C filter, which can be used for wireless sensor network applications. The filter can operate as the channel select filter and variable gain amplifier, simultaneously. The gain of the filter can be tuned from ?1 to 23 dB, which results in power consumptions of 187.2 to 450.6 μW, respectively. The proposed OTA and filter have been simulated in a 0.18 µm CMOS technology. Simulations of process corners and temperature variations are also included in the paper. Copyright © 2014 John Wiley & Sons, Ltd.     

超宽带脉冲信号的一种频域采样和接收方法

对纳秒级的超宽带脉冲信号进行采样需要设计采样速率高达数十GHz,且必须具有较低功耗的超高速模数变换器,提出了一种频域模数变换的方法,使超宽带脉冲信号通过一个频域滤波器组,并采用一组低速模数变换器在频域对脉冲信号并行采样,大大地降低了接收机对前端模数变换器采样速率的要求。并给出了频域同步、频域信道估计和频域解调的设计算法,计算机仿真结果证明了在能够大大降低采样速率的情况下,频域采样超宽带脉冲通信接收机具有和传统时域高速采样接收机相近的误码率性能。     

A 0.6‐V sub‐mW X‐band RFSOI CMOS LNA with novel complementary current‐reused technique

A fully integrated 0.6 V low‐noise amplifier (LNA) for X‐band receiver application based on 0.18 μm RFSOI CMOS technology is presented in this paper. To achieve low noise and high gain with the constraint of low voltage and low power consumption, a novel modified complementary current‐reused LNA using forward body bias technique is proposed. A diode connected MOSFET forward bias technique is employed to minimize the body leakage and improve the noise performance. A notch filter isolator is constructed to improve the linearity of low voltage. The measured results show that the proposed LNA achieves a power gain of 11.2 dB and a noise figure of 3.8 dB, while consuming a DC current of only 1.6 mA at supply voltage of 0.6 V. Copyright © 2017 John Wiley & Sons, Ltd.     

A new two‐step single slope A/D converter for using in CMOS image sensors

This paper presents a high‐speed, high‐resolution column parallel analog‐to‐digital converter (ADC) with global digital error correction. Proposed A/D converter is suitable for using in high‐frame‐rate complementary metal–oxide–semiconductor (CMOS) image sensors. This new method has more advantages than conventional ramp ADC from viewpoint of speed and resolution. A prototype 11‐bit ADC is designed in 0.25‐µm CMOS technology. Moreover, an overall signal‐to‐noise ratio of 63.8 dB can be achieved at 0.5Msample/s. The power dissipation of all 320 column‐parallel ADCs with the peripheral circuits consume 76 mW at 2.5‐V supplies. Copyright © 2012 John Wiley & Sons, Ltd.     

Low‐power design of CMOS baseband analog chain for direct conversion receiver

A low‐power CMOS receiver baseband analog (BBA) circuit based on alternating filter and gain stage is reported. For the given specifications of the BBA block, optimum allocation of the gain, input‐referred third‐order intercept point (IIP3), and noise figure (NF) of each block is performed to minimize current consumption. The fully integrated receiver BBA chain is fabricated in 0.18µm CMOS technology and IIP3 of 30 dBm with a maximum gain of 59 dB and NF of 31 dB are obtained at 3.6 mW power consumption. Copyright © 2008 John Wiley & Sons, Ltd.     

A low‐power,area‐efficient multichannel receiver for micro MRI

A new integrated, low‐noise, low‐power, and area‐efficient multichannel receiver for magnetic resonance imaging (MRI) is described. The proposed receiver presents an alternative technique to overcome the use of multiple receiver front‐ends in parallel MRI. The receiver consists of three main stages: low‐noise pre‐amplifier, quadrature down‐converter, and a band pass filter (BPF). These components are used to receive the nuclear magnetic resonance signals from a 3 × 3 array of micro coils. These signals are combined using frequency domain multiplexing (FDM) method in the pre‐amplifier and BPF stages, then amplified and filtered to remove any out‐of‐band noise before providing it to an analog‐to‐digital converter at the low intermediate frequency stage. The receiver is designed using a 90 nm CMOS technology to operate at the main B₀ magnetic field of 9.4 T, which corresponds to 400 MHz. The receiver has an input referred noise voltage of 1.1 nV/√Hz, a total voltage gain of 87 dB, a power consumption of 69 mA from a 1 V supply voltage, and an area of 305 µm × 530 µm including the reference current and bias voltage circuits. Copyright © 2013 John Wiley & Sons, Ltd.     

A 14b 150 MS/s 140 mW 2.0 mm2 0.13µm CMOS A/D converter for software‐defined radio systems

This work proposes a 14 b 150 MS/s CMOS A/D converters (ADC) for software‐defined radio systems requiring simultaneously high‐resolution, low‐power, and small chip area at high speed. The proposed calibration‐free ADC employs a wide‐band low‐noise input sample‐and‐hold amplifier (SHA) along with a four‐stage pipelined architecture optimizing scaling‐down factors for the sampling capacitance and the input trans‐conductance of amplifiers in each stage to minimize thermal noise effect and power consumption. A signal‐insensitive 3‐D fully symmetric layout achieves a 14 b level resolution by reducing a capacitor mismatch of three MDACs. The prototype ADC in a 0.13µm 1P8M CMOS technology demonstrates a measured differential nonlinearity (DNL) and integral nonlinearity within 0.81LSB and 2.83LSB at 14 b, respectively. The ADC shows a maximum signal‐to‐noise‐and‐distortion ratio of 64 and 61 dB and a maximum spurious‐free dynamic range of 71 and 70 dB at 120 and 150 MS/s, respectively. The ADC with an active die area of 2.0mm² consumes 140 mW at 150 MS/s and 1.2 V. Copyright © 2010 John Wiley & Sons, Ltd.     

A 0.008‐mm2, 35‐μW, 8.87‐ps‐resolution CMOS time‐to‐digital converter using dual‐slope architecture

This paper presents a high resolution time‐to‐digital converter (TDC) for low‐area applications. To achieve both high resolution and low circuit area, we propose a dual‐slope voltage‐domain TDC, which is composed of a time‐to‐voltage converter (TVC) and an analog‐to‐digital converter (ADC). In the TVC, a current source and a capacitor are used to make the circuit as simple as possible. For the same reason, a single‐slope ADC, which is commonly used for compact area ADC applications, is adapted and optimized. Because the main non‐linearity occurs in the current source of the TVC and the ramp generator of the ADC, a double gain‐boosting current source is applied to overcome the low output impedance of the current source in the sub‐100‐nm CMOS process. The prototype TDC is implemented using a 65‐nm CMOS process, and occupies only 0.008 mm². The measurement result shows a dynamic range with an 8‐bit 8.86‐ps resolution and an integrated non‐linearity of ±1.25 LSB. Copyright © 2016 John Wiley & Sons, Ltd.     

A 7.5‐μW 0.08‐mm2 single‐ended SC delta‐sigma ADC for acoustic sensor applications

This study presents an ultra‐low‐power, small‐size, 1‐bit, single‐ended, and switched‐capacitor (SC) delta‐sigma analog‐to‐digital converter (ADC) for wireless acoustic sensor nodes. This wireless sensor node has a delta‐sigma ADC that converts the sensed signal to a digital signal for convenient data processing and emphasizes the features of small size and low‐power consumption. The chip area of the delta‐sigma ADC is dominated by the capacitor; therefore, a novel common‐mode (CM) controlling technique with only transistors is proposed. This ADC achieves an extremely small size of 0.08 mm² in a 130‐nm CMOS process. The conventional operational transconductance amplifiers (OTAs) are replaced by inverters in the weak inversion region to achieve high power efficiency. At 4‐MHz sampling frequency and 0.7‐V power supply voltage, the delta‐sigma ADC achieves a 55.8‐dB signal‐to‐noise‐plus‐distortion ratio (SNDR) and a 298‐fJ/step figure‐of‐merit (FOM) in a signal bandwidth of 25 kHz, while consuming only 7.5 μW of power. Copyright © 2015 John Wiley & Sons, Ltd.     

Implementation of an in‐field CMOS frequency division multiplexer for 9.4 T magnetic resonance applications

This paper introduces the implementation of an application‐specific complementary metal oxide semiconductor frequency division multiplexer as a novel solution to interface magnetic resonance (MR) phased arrays of micro‐detectors to an image‐processing unit, thus reducing the complexity and space issues associated with MR detector arrays. The frequency multiplexer, in a compact 3 × 4 mm silicon die, is designed to operate at 400 MHz, which is the Larmor frequency of ¹H protons in a 9.4‐T MR imaging system. The system implements eight channels, where each channel consists of a low‐noise amplifier, a frequency mixer, and a band‐pass filter. The maximum gain of an individual channel after the band‐pass filter stage is 38 dB. The suppression of the local oscillator ranges from 40 to ?51 dB, and the maximum coupling between channels is ?39 dB. The input dynamic range of an individual channel is 8 mV. Each channel consumes 54 mA from a 3.3‐V source. The chip operates without errors within a high 9.4‐T magnetic field. Copyright © 2014 John Wiley & Sons, Ltd.     

Selectivity and sensitivity enhancement methods for high‐data‐rate super‐regenerative receiver

This paper describes selectivity and sensitivity performance evaluations and improvement methods for an on–off keying super‐regenerative (SR) receiver. A slope‐controlled quasi‐exponential quench waveform, generated by a low‐complexity PVT‐tolerant quench generator circuit, is proposed to increase data rate and reduce the receiver 3‐dB bandwidth, thereby preventing oscillation caused by out‐of‐band injected signals and improving the receiver selectivity. The SR receiver sensitivity is also enhanced by a noise‐canceling front‐end topology with single‐ended to differential (S2D) signal converter. To exemplify these techniques, we designed an SR receiver with the proposed front‐end and quench waveform generator in a 0.18‐μm CMOS technology. Theoretical analyses and circuit simulations show 30% and 65% reduction in 3‐dB bandwidth of the SR receiver at 25 Mbps data rate by employing the proposed quench signal compared with piecewise‐linear and trapezoidal quench waveforms, respectively. Performance of the proposed front‐end is evaluated by a fast bit‐error‐rate estimation procedure, based on circuit noise simulations and statistical analyses, without the need for time‐consuming transient‐noise simulations. Accuracy of the procedure has been verified by comparing its results with transient‐noise simulations. According to the estimated bit‐error‐rate curves, the noise‐canceling topology with S2D converter enhances the SR receiver sensitivity by 9 dB. Copyright © 2017 John Wiley & Sons, Ltd.     

A 10 b 25 MS/s 4.8 mW 0.13 µm CMOS ADC with switched‐bias power‐reduction techniques

This paper proposes a 10 b 25 MS/s 4.8 mW 0.13 µm CMOS analog‐to‐digital converter (ADC) for high‐performance portable wireless communication systems, such as digital video broadcasting, digital audio broadcasting, and digital multimedia broadcasting (DMB) systems, simultaneously requiring a low‐voltage, low‐power, and small chip area. A two‐stage pipeline architecture optimizes the overall chip area and power dissipation of the proposed ADC at the target resolution and sampling rate, while switched‐bias power‐reduction techniques reduce the power consumption of the power‐hungry analog amplifiers. Low‐noise reference currents and voltages are implemented on chip with optional off‐chip voltage references for low‐power system‐on‐a‐chip applications. An optional down‐sampling clock signal selects a sampling rate of 25 or 10 MS/s depending on applications in order to further reduce the power dissipation. The prototype ADC fabricated in a 0.13 µm 1P8M CMOS technology demonstrates a measured peak differential non‐linearity and integral non‐linearity within 0.42 LSB and 0.91 LSB and shows a maximum signal‐to‐noise‐and‐distortion ratio and spurious‐free dynamic range of 56 and 65 dB at all sampling frequencies up to 25 MHz, respectively. The ADC with an active die area of 0.8 mm² consumes 4.8 and 2.4 mW at 25 and 10 MS/s, respectively, with a 1.2 V supply. Copyright © 2008 John Wiley & Sons, Ltd.     

Low‐frequency noise analysis and minimization in Gilbert‐cell‐based mixers for direct‐conversion (zero‐IF) low‐power front‐ends

Low‐frequency (flicker) noise is one of the most important issues in the design of direct‐conversion zero‐IF front‐ends. Within the front‐end building blocks, the direct‐conversion mixer is critical in terms of flicker noise, since it performs the signal down‐conversion to baseband. This paper analyzes the main sources of low‐frequency noise in Gilbert‐cell‐based direct‐conversion mixers, and several issues for minimizing the flicker noise while keeping a good mixer performance in terms of gain, noise figure and power consumption are introduced in a quantitative manner. In order to verify these issues, a CMOS Gilbert‐cell‐based zero‐IF mixer has been fabricated and measured. A flicker noise as low as 10.4 dB is achieved (NF at 10 kHz) with a power consumption of only 2 mA from a 2.7 V power supply. More than 14.6 dB conversion gain and noise figure lower than 9 dB (DSB) are obtained from DC to 2.5 GHz with an LO power of ?10 dBm, which makes this mixer suitable for a multi‐standard low‐power zero‐IF front‐end. Copyright © 2008 John Wiley & Sons, Ltd.     

A 6th‐order 75 dB‐DR 10.7 MHz 3.3 V CMOS bandpass ΣΔ modulator sampled at 37.05 MHz

This paper describes the design and the implementation of a 6th‐order bandpass ΣΔ modulator to be used for IF digitizing at 10.7 MHz of a broadcasting FM radio signal. The modulator is sampled at 37.05 MHz. This sampling frequency value allows to optimize both modulator and overall receiver channel performance. The modulator has been implemented in a standard double‐poly 0.35 µm CMOS technology using switched capacitor (SC) technique and consumes 116 mW from a single 3.3 V power supply. The modulator features 75 dB dynamic range and 66 dB peak‐SNR within a 200 kHz bandwidth (FM bandwidth). Third‐order intermodulation products are suppressed by –78dBc. Copyright © 2004 John Wiley & Sons, Ltd.     

Explicit design formulas for current‐mode leap‐frog OTA‐C filters and 300 MHz CMOS seventh‐order linear phase filter

The leap‐frog (LF) configuration is an important structure in analogue filter design. Voltage‐mode LF OTA‐C filters have recently been studied in the literature; however, general explicit formulas do not exist for current‐mode LF OTA‐C filters and there is also need for current‐mode LF‐based OTA‐C structures for realization of arbitrary transmission zeros. Three current‐mode OTA‐C structures are presented, including the basic LF structure and LF filters with an input distributor or an output summer. They can realize all‐pole characteristics and functions with arbitrary transmission zeros. Explicit design formulas are derived directly from these structures for the synthesis of, respectively, all‐pole and arbitrary zero filter characteristics of up to the sixth order. The filter structures are regular and the design formulas are straightforward to use. As an illustrative example, a 300 MHz seventh‐order linear phase low‐pass filter with zeros is presented. The filter is implemented using a fully differential linear operational transconductance amplifier (OTA) based on a source degeneration topology. Simulations in a standard TSMC 0.18µm CMOS process with 2.5 V power supply have shown that the cutoff frequency of the filter ranges from 260 to 320 MHz, group delay ripple is about 4.5% over the whole tuning range, noise of the filter is 420nA/√Hz, dynamic range is 66 dB and power consumption is 200 mW. Copyright © 2008 John Wiley & Sons, Ltd.     

Harmonic fold back reduction at the N‐path filters

In this paper, a method is proposed to reduce harmonic fold back (HFB) problem of N‐path filters, without increasing the input reference clock (f_CLK ) frequency. The HFB at the N‐path filter is analyzed, and simple expressions are extracted to model this problem. Using the results of the analysis, an M‐of‐N‐path filter has been proposed that behaves like an M × N‐path filter in terms of HFB problem; however, the f_CLK frequency of this structure is the same as an N‐path filter. To demonstrate the feasibility of the proposed idea, a 3‐of‐4‐path filter is designed, and its characteristics are compared with 4‐path and 12‐path filters by simulation. Impacts of different non‐idealities like clock‐phase error, mismatch, and parasitic capacitance are investigated. The transistor‐level implementation of this filter is performed in 0.18 µm Complementary Metal Oxide Semiconductor (CMOS) technology. The simulation results show that the filter has the pass‐band gain of 17 dB, tuning range of 0.2–1.2 GHz, −3 dB bandwidth of 25 MHz, quality factor of 8–48, 18 dB out‐of‐band rejection, 16 dB rejection of the third harmonic of switching frequency (f_s ), and the noise figure of 4.35 dB (using ideal G_m cells) and 6.95 dB (for practical G_m cells). The strongest harmonic folding to the filter pass‐band occurs around 11f_s with the attenuation of 23.8 dB. Each G_m cell draws about 12.4 mA from 1.8 V supply, and the out‐of‐band IIP3 and P _{1 dB,CP} are 17 and 4 dBm, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Wide‐band aperture array using a four‐channel manifold‐type planar multiplexer and digital 2‐D IIR filterbank

Emerging wide‐band communications and spectrum‐sensing systems demand support for multiple electronically scanned beams while maintaining a frequency independent, constant far‐field beam width. Realizing existing phased‐array technology on a digital scale is computationally intensive. Moreover, digitizing wide‐band signals at Nyquist rate requires complex high‐speed analog‐to‐digital converters (ADCs), which is challenging for real developments driven by the current ADC technology. A low‐complexity alternative proposed in this paper is the use of radio‐frequency (RF) channelizers for spectrum division followed by sub‐sampling of the RF sub‐bands, which results in extensive reduction of the necessary ADC operative frequency. The RF‐channelized array signals are directionally filtered using 2‐D digital filterbanks. This mixed‐domain RF/digital aperture array allows sub‐sampling, without utilizing multi‐rate 2‐D systolic arrays, which are difficult to realize in practice. Simulated examples showing 14–19 dB of rejection of wide‐band interference and noise for a processed bandwidth of 1.6 GHz are demonstrated. The sampling rate is 400 MHz. The proposed VLSI hardware uses a single‐phase clock signal of 400 MHz. Prototype hardware realizations and measurement using 65‐nm Xilinx field‐programmable gate arrays, as well as Cadence RTL synthesis results including gate counts, area‐time complexity, and dynamic power consumption for a 45‐nm CMOS circuit operating at B _DC = 1.1 V, are presented. Copyright © 2016 John Wiley & Sons, Ltd.