共查询到20条相似文献,搜索用时 78 毫秒
1.
旋风反应器内压力降及分离效率的计算及测定 总被引:8,自引:2,他引:8
利用模型计算了旋风反应器的压力降及分级分离效率,并通过了实验验证。结果表明,模型计算结果与实验数据基本一致,可以作为旋风反应器设计的理论依据。 相似文献
2.
提出了R32制冷剂在饱和线(?130~78℃,0.00013~5.76 MPa)范围内饱和蒸气压、液体密度等关联式的计算模型,在此基础上推导了蒸发潜热的计算模型;建立了描述饱和气体线上(?130~78℃,0.00013~5.76 MPa)及过热区(过热度为100℃)范围内描述P-v-T关系的状态方程;在上述模型的基础上推导得到了饱和气体线及过热区范围内焓、熵、比热容的计算模型。将模型计算结果与REFPROP9.0数据源、已发表的状态方程及公开实验数据对比,各关联式计算模型的平均相对偏差均小于0.16%,最大相对偏差不超过3.7%,与已有状态方程和公开数据对比偏差小于8.7%;基于状态方程和热力学关系式推导得到的焓、熵、比热容的计算模型的平均相对偏差均小于5.2%,最大相对偏差不超过9.1%。 相似文献
3.
单螺杆挤出过程粒子熔融理论 总被引:2,自引:0,他引:2
基于宏观和亚宏观可视化实验观察到的单螺杆挤出过程粒子熔融现象,提出了与宏观熔融模型相结合的粒子熔融渗流模型,利用该模型计算了LDPE在熔融初期的熔融速率,并将计算结果与实验结果进行了比较。 相似文献
4.
5.
气液两相流中,准确预测段塞流的特征参数具有重要的现实意义。Renault模型是基于非黏性Kelvin-Helmholtz(IKH)稳定性准则与黏性Kelvin-Helmholtz(VKH)稳定性准则建立的能够捕捉段塞前后界面运动的双流体模型,但该模型在液相单元格之间采用Riemann精确解,求解速度较慢。为简化计算,本文将行波法引入到Renault模型的液相方程求解过程,并对可能出现的干区用薄液膜代替,使行波法适用于所有计算单元,在保证模型精度的条件下,极大地提高了计算速度,运算时间相比Renault模型平均减少28%。对比本模型计算结果与室内小型环道实验数据,持液率与实测结果相一致,压降、段塞长度计算相对误差分别在25%、30%以内,且主要分布在20%以内。说明本文改进的瞬态段塞流模型具备运算快速、计算精度较高的特点,具有一定的工程应用价值。 相似文献
6.
7.
8.
为了深入研究机载蒸发循环系统的工作特性及为搭建仿真计算模型做准备,基于试验室已有设备和条件,以一台新型微通道换热器作为研究对象,以R134a为工质,通过控制压缩机转速和电子膨胀阀开度一定,分别调节冷源温度和流量,考察冷源温度和流量对压缩机入口过热度、热源出口温度和制冷量的影响,并基于试验数据搭建了针对该蒸发器的仿真计算模型。试验结果表明在试验工况下,冷源防冻液入口温度对系统性能的影响明显,随冷源入口温度升高,压缩机入口过热度逐渐降低、热源出口温度明显升高,但冷源流量对系统性能的影响不显著。基于试验数据,建立了蒸发器仿真计算模型,将该模型应用于蒸发循环系统模型中,对比试验数据和仿真计算数据,可知,该蒸发器仿真计算模型准确可靠,可用于针对该蒸发器的性能仿真计算。 相似文献
9.
单螺杆挤出过程固体输送段的数值模拟 总被引:4,自引:0,他引:4
介绍了挤出成型过程数值模拟的现状及现有通用计算流体力学(CFD)软件在模拟聚合物流动时存在的缺陷,指出自主开发CFD程序的必要性。针对单螺杆挤出过程固体输送段的数值模拟方法,讨论了传统塞流固体输送理论的缺陷,介绍了非塞流固体输送理论的优越性及相关的有限元计算方法。并针对有限元方法的复杂性,介绍了简化的三层模型方法。计算结果表明:非塞流固体输送理论的三层模型法与有限元法计算结果接近,且优于塞流固体输送理论,而三层模型法计算方法简单,便于其在工程计算中的应用。 相似文献
10.
11.
我厂3号回转窑(Φ4m×60m)生产线在1996年年底由SP窑(产量912t/d)改为NSP窑(产量1320t/d),预分解系统为四级旋风预热器带离线式分解炉 相似文献
12.
13.
14.
乙烯酮(双乙烯酮)是十分重要的化工中间体,其下游产品较多。江苏某化工厂开发生产乙烯酮(双乙烯酮)下游产品三十多个,年生产规模三万多吨,是国内以乙烯酮(双乙烯酮)为中间体生产精细化学品的综合骨干企业。针对乙烯酮(双乙烯酮)下游产品废水特点,该厂结合企业实际,开展了产品优化,结构调整,清洁生产,资源循环利用,节水降耗等工作,从源头削减了污染物的生产。同时投资二千多万元新建预处理装置三套,6000m3/d废水生化处理装置一套,使全厂乙烯酮(双乙烯酮)下游产品的废水得到了有效的治理。 相似文献
15.
16.
17.
The objective of the study was to explore the effect of the degree of deacetylation (DD) of the chitosan used on the degradation rate and rate constant during ultrasonic degradation. Chitin was extracted from red shrimp process waste. Four different DD chitosans were prepared from chitin by alkali deacetylation. Those chitosans were degraded by ultrasonic radiation to different molecular weights. Changes of the molecular weight were determined by light scattering, and data of molecular weight changes were used to calculate the degradation rate and rate constant. The results were as follows: The molecular weight of chitosans decreased with an increasing ultrasonication time. The curves of the molecular weight versus the ultrasonication time were broken at 1‐h treatment. The degradation rate and rate constant of sonolysis decreased with an increasing ultrasonication time. This may be because the chances of being attacked by the cavitation energy increased with an increasing molecular weight species and may be because smaller molecular weight species have shorter relaxation times and, thus, can alleviate the sonication stress easier. However, the degradation rate and rate constant of sonolysis increased with an increasing DD of the chitosan used. This may be because the flexibilitier molecules of higher DD chitosans are more susceptible to the shear force of elongation flow generated by the cavitation field or due to the bond energy difference of acetamido and β‐1,4‐glucoside linkage or hydrogen bonds. Breakage of the β‐1,4‐glucoside linkage will result in lower molecular weight and an increasing reaction rate and rate constant. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3526–3531, 2003 相似文献
18.
Conclusions It is significant that the purification on a single passage of viscose through porous ceramic corresponds to the result of a two-stage filtration of it in industrial filter-presses with standard fillings.Kiev Combine. Kiev Technological Institute of Light Industry. Translated from Khimicheskie Volokna, No. 3, pp. 20–22, May–June, 1969. 相似文献
19.
20.
A refined nonlinear value of the main parameter of a material, i.e., the elongation modulus versus the instant temperature value, was suggested for introduction into the computational algorithm of tempering stresses. 相似文献