Effect of air distributor on the fluidization characteristics in conical gas fluidized beds

The effect of an air distributor on the fluidization characteristics of 1 mm glass beads has been determined in a conical gas fluidized bed (0.1 m-inlet diameter and 0.6 m in height) with an apex angle of 20‡. To determine the effect of distributor geometry, five different perforated distributors were employed (the opening fraction of 0.009–0.037, different hole size, and number). The differential bed pressure drop increases with increasing gas velocity, and it goes from zero to a maximum value with increasing or decreasing gas velocity. From the differential bed pressure drop profiles with the distributors having different opening fractions, demarcation velocities of the minimum and maximum velocities of the partial fluidization, full fluidization, partial defluidization and the full defluidization are determined. Also, bubble frequencies in the conical gas fluidized beds were measured by an optical probe. In the conical bed, the gas velocity at which the maximum bed pressure drop attained increases with increasing the opening fraction of distributors.     

过热蒸汽流化床流化特性的实验研究

在底部直径为120 mm的锥型流化床中,以玻璃珠为流化颗粒,过热蒸汽为流化介质,研究了固体颗粒在过热蒸汽流化床中的流化特性,考察了操作温度和压力对临界流化速度(umf)的影响.结果表明,过热蒸汽流化床的流化行为与热空气相似,临界流化速度(umf)随床层温度的升高而减小,随床内压力的增大而减小;在相同温度条件下,过热蒸汽流化床的临界流化速度比热空气大.     

Simulation and experiment of segregating/mixing of rice husk–sand mixture in a bubbling fluidized bed

The fluidization behavior of rice husk–sand mixture in the gas bubbling fluidized bed is experimentally and theoretically studied. The relevancy of the pressure drop profile of rice husk–sand mixture to the definition of its minimum fluidization velocity is discussed, and the minimum fluidization velocity of rice husk–sand binary mixture is determined. The distributions of mass fraction of rice husk particles along the bed height are measured, and the profiles of the mean particle diameter of mixture are determined. A multi-fluid gas–solid flow model is presented where equations are derived from the kinetic theory of granular flow. Separate transport equations are constructed for each of the particle classes, allowing for the interaction between particle classes, as well as the momentum and energy are exchanged between the respective classes and the carrier gas. The distributions of the mass fraction of rice husk particles and the mean particle diameter of binary mixture are predicted. The numerical results are analyzed, and compared with experimental data.     

Bed height and material density effects on fluidized bed hydrodynamics

Characterizing the hydrodynamics of a fluidized bed is of vital importance to understanding the behavior of this multiphase flow system. Minimum fluidization velocity and gas holdup are two of these key characteristics. Experimental studies addressing the effects of bed height and material density on the minimum fluidization velocity and gas holdup were carried out in this study using a 10.2 cm diameter cylindrical fluidized bed. Three different Geldart type-B particles were tested: glass beads, ground walnut shell, and ground corncob, with material densities of 2600, 1300, and 1000 kg/m³, respectively. The particle size range was selected to be the same for all three materials and corresponded to 500–600 μm. In this study, five different bed height-to-diameter ratios were investigated: H/D=0.5, 1, 1.5, 2, and 3. Minimum fluidization velocity was determined for each H/D ratio using pressure drop measurements. Local time-average gas holdup was determined using non-invasive X-ray computed tomography imaging. Results show that minimum fluidization velocity is not affected by the change in bed height. However, as the material density increased, the minimum fluidization velocity increased. Finally, local time-average gas holdup values revealed that bed hydrodynamics were similar for all bed heights, but differed when the material density was changed.     

几种典型铁矿粉的流化特性

利用内径150 mm的D型有机玻璃流化床模型,对澳矿、巴西矿、北方矿和钒钛矿典型铁矿粉的流化特性进行了实验研究,获得了其流化特性曲线、初始流化速度和最大床层压降,并将初始流化速度的实测值和理论计算值进行了比较分析. 结果表明,矿粉粒度是影响其流化特性的最主要因素,粒径越大,床层所需要的初始流化速度越大,实测值和理论估算值基本相符;粒度小于0.125 mm钒钛矿流动性较差,在流化过程中易出现沟流现象;粒度范围较宽的矿粉,完全流态化时,细矿粉随气流夹带逸出明显;在粒度相同的情况下,几种不同的铁矿粉的开始流化速度接近,而床层压降有较大差异,巴西矿的床层压降明显大于其他三种铁矿粉. 最大床层压降的最小值均出现在粒度为0.25~0.425 mm,为铁矿粉流态化还原过程中较适宜的粒度范围.     

A parametric study of a horizontal rotating fluidized bed using slotted and sintered metal cylindrical gas distributors

The pressure drop in a horizontal rotating fluidized bed was measured using slotted and sintered metal cylindrical gas distributors as a function of rotating speed, gas velocity and bed thickness. Experiments were conducted using polydisperse alumina particles and nearly monodisperse glass beads. The pressure drop for the slotted distributor exhibited a much larger pressure overshoot at incipient fluidization than the sintered metal distributor. This behavior was also studied using high-resolution photography. Physically consistent explanations are presented for the observed phenomena. The experimental results are compared to theoretical models available in the literature.     

Drop properties and pressure fluctuations in liquid–liquid–solid fluidized-bed reactors

Characteristics of size, rising velocity and distribution of liquid drops were investigated in an immiscible liquid–liquid–solid fluidized-bed reactor whose diameter was 0.102 and 2.5 m in height. In addition, pressure fluctuations were measured and analyzed by adopting the theory of chaos, to discuss the relation between the properties of liquid drops and the resultant flow behavior of three (liquid–liquid–solid) phase in the reactor. Effects of velocities of dispersed (0–0.04 m s⁻¹) and continuous (0.02–0.14 m s⁻¹) liquid phases and fluidized particle size (1, 2.1, 3 or 6 mm) on the liquid drop properties and pressure fluctuations in the reactor were determined. The resultant flow behavior of liquid drops became more irregular and complicated with increasing the velocity of dispersed or continuous liquid phase, but less complicated with increasing fluidized particle size, in the beds of 1.0 or 2.1 mm glass beads. In the beds of 3.0 or 6.0 mm glass beads, the effects of continuous phase velocity was marginal. The resultant flow behavior of liquid drops was dependent strongly upon the drop size and its distribution. The drop size increased with increasing dispersed phase velocity, but decreased with increasing particle size. The drop size tended to increase with approaching to the center or increasing the height from the distributor. The size and rising velocity of liquid drops and correlation dimension of pressure fluctuations have been well correlated in terms of operating variables.     

A two-dimensional gas fluidized bed for hydrodynamic and elutriation studies

A two-dimensional fluidized bed having the dimensions of 52.1 cm (20.5 in) by 2.00 cm (0.787 in) is designed and tested for its use in hydrodynamic and elutriation studies. The fluidization column is provided with a calming section and freeboard which are 45.7 cm (18.0 in) and 129.5 cm (51.0 in) high respectively. A porous distributor plate is provided whose pressure drop is found to vary linearly with air velocity in the range of current interest. Fluidization experiments with three sand particles (788, 488 and 167 μm), glass beads (427 μm), millet (2064 μm) and green peas (4578 μm) are reported. Bed expansion and bubble growth characteristics are examined in some detail. Variations of bed height and pressure drop with fluidization velocity are analyzed to establish bed voidage as a function of gas velocity, and minimum fluidization velocity. The latter is also measured for three particles in a 0.305 m square fluidized bed. These studies reveal that two-dimensional fluidized beds are great tools for making novel qualitative investigations for mechanistic details of processes taking place in three-dimensional fluidized beds. Currently, investigations are underway for elutriation phenomenon.     

气固脉冲流化床流体力学特性的研究

在φ７０ｍｍ的流化床内，采用聚氯乙烯、玻璃珠和不规则天然刚玉等Ｂ类、Ｄ类颗粒，测定了０￣５．０Ｈｚ脉冲频率下气固流化床的基本流体力学特性，探讨了影响床层流化特性的一些主要因素，并根据实验数据对脉冲流化床的临界流化速度和临界流化压降的无因次准数式进行了关联。     

含内构件的循环流化床的动态压力特性

针对含内构件的循环流化床,以石英砂为物料,使用动态压力传感器测量了含内构件的流化床中气固两相流的动态压力,分析了床内的瞬时压力特性. 结果表明,在进出口总压降中,文丘里压降最大,占主床压降的60%以上. 表观气速和固体颗粒循环流率共同影响循环流化床内的压力特性. 压力瞬时波动功率谱分析表明,压力波动对应一个主频,表观气速越小、颗粒循环流率越大时,压力波动越大,且循环流化床底部压力波动比上部大. 加入内构件能有效引导气流,使流动更均匀.     

Hydrodynamics of Geldart group A particles in gas-solid fluidized beds

Geldart group A particles were fluidized in a 10 cm i.d.×1.8 m high Plexiglas-made bed with ambient air to determine the hydrodynamic properties in a gas-solid fluidized bed. The effects of static bed heights, position of pressure measuring points, differential and absolute pressure fluctuations on the hydrodynamic behavior of a Geldart group A particles in a gas-solid fluidized bed were investigated. The particles used in this study were 80 micrometer FCC powders and 60 micrometer glass beads. The variance of pressure fluctuations was used to find the minimum bubbling velocity. The obtained minimum bubbling velocity was compared with the other methods available in the literature. This method was found to be much easier and had better data reproducibility than the classical visual method or sedimentation method. The variance of pressure fluctuations increased due to the increase of superficial gas velocity and static bed height. The obtained minimum bubbling velocity and pressure fluctuations were found to depend on the measuring position along the axial direction. The effect of measuring position was discussed. Cross-correlation of two pressure signals was used to find the delay time, then the bubble rising velocity.     

Fluidization of Group B particles with a rotating distributor

A novel rotating distributor fluidized bed is presented. The distributor is a rotating perforated plate, with 1% open-area ratio. This work evaluates the performance of this new design, considering pressure drop, Δp, and quality of fluidization. Bed fluidization was easily achieved with the proposed device, improving the solid mixing and the quality of fluidization.In order to examine the effect of the rotational speed of the distributor plate on the hydrodynamic behavior of the bed, minimum fluidization velocity, U_mf, and pressure fluctuations were analyzed. Experiments were conducted in the bubbling free regime in a 0.19 m i.d. fluidized bed, operating with Group B particles according to Geldart's classification. The pressure drop across the bed and the standard deviation of pressure fluctuations, σ_p, were used to find the minimum fluidization velocity, U_mf. A decrease in U_mf is observed when the rotational speed increases and a rise in the measured pressure drop was also found. Frequency analysis of pressure fluctuations shows that fluidization can be controlled by the adjustable rotational speed, at several excess gas velocities.Measurements with several initial static bed heights were taken, in order to analyze the influence of the initial bed mass inventory, over the effect of the distributor rotation on the bed hydrodynamics.     

Distribution of large biomass particles in a sand‐biomass fluidized bed: Experiments and modeling

The axial distribution of large biomass particles in bubbling fluidized beds comprised of sand and biomass is investigated in this study. The global and local pressure drop profiles are analyzed in mixtures fluidized at superficial gas velocities ranging from 0.2 to 1 m/s. In addition, the radioactive particle tracking technique is used to track the trajectory of a tracer mimicking the behavior of biomass particles in systems consisting of 2, 8, and 16% of biomass mass ratio. The effects of superficial gas velocity and the mixture composition on the mixing/segregation of the bed components are explored by analyzing the circulatory motion of the active tracer. Contrary to low fluidization velocity (U = 0.36 m/s), biomass circulation and distribution are enhanced at U = 0.64 m/s with increasing the load of biomass particles. The axial profile of volume fraction of biomass along the bed is modeled on the basis of the experimental findings. © 2014 American Institute of Chemical Engineers AIChE J, 60: 869–880, 2014     

气-固微型流化床压降特性及最小流化速度的实验研究

在内径3~20 mm的4个气?固微型流化床中,分别考察了A类和B类两种类型颗粒的流化特性,同时研究了床几何结构、操作条件、物相性质等各因素对其最小流化速度的影响。结果表明,气?固微型流化床中的床层压降特性与颗粒类型密切相关,不同的流动状态下两种类型颗粒的流动特性存在显著地差异。在固定床阶段,与B类颗粒相比,A类颗粒与壁面间的相互作用更强,导致实验压降值偏离计算值更大;在流化床阶段,较大颗粒粒径和密度的B类颗粒在床层内表现出了更高的气泡聚并和破裂程度,加剧了颗粒间的碰撞,增加了能量损失,从而形成了较高的实验压降。气?固微型流化床的最小流化速度除了与操作条件和物相性质有关外,床内径与静态床层高度对其也会产生显著影响。随着床径减小及静态床高增加,最小流化速度逐渐增加。综合考察各影响的因素,提出了适用于实验考察范围内预测微型流化床最小流化速度的经验关联式。     

Fundamental particle fluidization behavior and handling of nano-particles in a rotating fluidized bed

The fluidization behavior of the three kinds of nano-particles (TiO₂, SiO₂, Al₂O₃) was analyzed in a rotating fluidized bed (RFB). Bed pressure drop, minimum fluidization velocity, bed expansion, entrainment and particle mixing characteristics under various centrifugal accelerations were experimentally investigated. The effects of centrifugal acceleration on agglomerate size and density were analyzed based on a Richardson-Zaki approach coupled with a fractal model.The bed pressure drop behavior showed almost similar to that of A or B-particles of Geldart's classification. Dimensionless particle bed height became smaller when the centrifugal acceleration was larger. Size of agglomerate decreased and its density increased with an increase in centrifugal acceleration. The agglomerate size in the RFB showed smaller than that in other types of fluidized bed system such as vibration and magnetic field as well as in a conventional fluidized bed, and the agglomerate density became larger. Particle entrainment became smaller in the case of the higher centrifugal acceleration. These results confirmed that the RFB can reduce the size of a nano-particle agglomerate and fluidize nano-particles at high gas velocity without any significant entrainment. The RFB is thus expected as more effective gas-solid fluidization system for handling of a large amount of nano-particles than other types of fluidized bed.     

SHANNON ENTROPY ANALYSIS OF DYNAMIC BEHAVIOR OF GELDART GROUP B AND GELDART GROUP D PARTICLES IN A FLUIDIZED BED

Pressure fluctuations resulting from the nonuniform flow behavior of solid particles in a fluidized bed (0.06 m ID × 5.0 m in height) were analyzed using the Shannon entropy analysis method. Particles representing Geldart group B and group D types were employed in the experiments. Results show that with the increase of the superficial gas velocity, transitions between bubbling fluidization, turbulent fluidization, and fast fluidization were effectively detected based on the Shannon entropy of pressure fluctuations in the bed. Meanwhile, a higher static bed height resulted in a larger value of Shannon entropy due to the wall effect of smaller diameter column and the greater resistance to bubble formation affected by the increased weight of the bed. Comparison of the particle types indicated that despite the different details of their behavior, the overall trends were similar.     

Experimental and numerical research for fluidization behaviors in a gas–solid acoustic fluidized bed

The effects of sound assistance on fluidization behaviors were systematically investigated in a gas–solid acoustic fluidized bed. A model modified from Syamlal–O'Brien drag model was established. The original solid momentum equation was developed and an acoustic model was also proposed. The radial particle volume fraction, axial root‐mean‐square of bed pressure drop, granular temperature, and particle velocity in gas–solid acoustic fluidized bed were simulated using computational fluid dynamics (CFD) code Fluent 6.2. The results showed that radial particle volume fraction increased using modified drag model compared with that using the original one. Radial particle volume fraction was revealed as a parabolic concentration profile. Axial particle volume fraction decreased with the increasing bed height. The granular temperature increased with increasing sound pressure level. It showed that simulation values using CFD code Fluent 6.2 were in agreement with the experimental data. © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Fluidization and hydraulic behaviour of natural zeolite particles used for removal of contaminants from wastewater

Fluidization, bed expansion, pressure drop, and hydraulic characteristics of beds of natural zeolite particles have been studied for their potential application in the treatment of aqueous waste. The measurements in the bed of zeolite particles are compared with regular shaped glass beads. The bed of zeolite particles required to be fully fluidized before getting reproducible pressure measurements in the bed. This is attributed to their wider size distribution and resulting segregation. The mean size of the particles ranged from 550 to 900 µm. Minimum fluidization velocity was determined from pressure measurements below the distributor and compared with values from pressure measurements inside the bed. Experiments conducted with slurry out the bed showed that it could be easily drained in expanded mode from the column through a small diameter opening near the bottom.     

生物质快速热解流化床反应器气力进料特性

为探究不同工况下热解流化床反应器的气力进料特性,设计并搭建了流化床反应器气力进料冷态试验装置。生物质原料和床料分别采用落叶松颗粒和石英砂颗粒,通过试验测得了本装置的最小流化速度,研究了流化气速、喷动气速、流量比、初始静床高、石英砂粒径、落叶松粒径对流化床反应器气力进料特性的影响。试验结果表明：流化气速和喷动气速的增加均会提高进料率;流化气使床料流化并为落叶松颗粒提供进料空间,喷动气为落叶松颗粒提供动能,并平衡一部分床层压力;落叶松与石英砂粒径的增加对进料效果不利;流量比在1.9~2.7范围内进料率高且稳定性好。本文构建了生物质、床料与气体的三相流物理及数学模型,开展试验对模型进行验证,结果表明其预测误差为±13%。     

Optimization fluidization characteristics conditions of nickel oxide for hydrogen reduction by fluidized bed reactor

We evaluated the optimal conditions for fluidization of nickel oxide (NiO) and its reduction into high-purity Ni during hydrogen reduction in a laboratory-scale fluidized bed reactor. A comparative study was performed through structural shape analysis using scanning electron microscopy (SEM); variance in pressure drop, minimum fluidization velocity, terminal velocity, reduction rate, and mass loss were assessed at temperatures ranging from 400 to 600 °C and at 20, 40, and 60 min in reaction time. We estimated the sample weight with most active fluidization to be 200 g based on the bed diameter of the fluidized bed reactor and height of the stocked material. The optimal conditions for NiO hydrogen reduction were found to be height of sample H to the internal fluidized bed reactor diameter D was H/D=1, reaction temperature of 550 °C, reaction time of 60 min, superficial gas velocity of 0.011 m/s, and pressure drop of 77 Pa during fluidization. We determined the best operating conditions for the NiO hydrogen reduction process based on these findings.